Ampac ACP-02 Manuel utilisateur

MAN2692-2

ACP-02 Addressable Manual Call Point Item Number: 4255-0200

Installation guide

Description

The Ampac ACP-02 double action re-settable Manual

Call Point (MCP) eliminates the possibility of accidental

operation and the cost and labour of replacement of

frangible elements.

Features

•Testing of operation without removal of front cover

•Resettable operation

•LED indication

•Two (2) 20mm conduit entries, one (1) top one (1)

bottom)

Installation

Observe anti-static precautions at all times

Surface Mounting

1. Locate the mounting box over a flat surface and

secure with at least two (2) screws tightened

evenly to prevent distortion

2. Remove the securing screw from the front of MCP

while at the same time pulling the top of the facia

away from the backing plate

3. Terminate cables (See Figure 1)

4. Set the address of the MCP (See Figure 2)

5. Remove the two (2) thread protection plugs from

the mounting box and fix the backing plate to it

using the two (2) fixing screws supplied

6. Replace the facia by inserting the two (2) bottom

locating pegs of the facia up into the bottom of the

locating holes of the backing plate, close at the top,

tighten the retaining screw then insert the key (as

shown) to reset the operation element

Testing of MCP Operation

1. Isolate the FACP from calling the fire brigade

2. Press on the clear ABS operation element in the

location indicated, PUSH HERE to drop the

element down

3. Operate the switch, the MCP LED should illuminate

and an alarm at the FACP should be indicated

4. To reset the operation element firmly push the key

up into the slot in the bottom of the facia

Note 1:

Set the device type in FireFinder

ConfigManager to S90 MCP

Note 2:

To ensure line monitoring integrity always use

one (1) set of terminals for “IN” and one (1) set for

“OUT”.

INSERT KEY

TO RESET

FACIA

FACIA RETAINING

SCREW

CLEAR ABS

OPERATION

ELEMENT KEY

BACKING

PLATE

MOUNTING BOX

REMOVE PLASTIC THREAD

INSERTS TO SCREW

FRONT ASSEMBLY

TO THE MOUNTING BOX

FRONT ASSEMBLY

AMPAC

PCB

KNOCKOUT

FACIA WITH THE

OPERATION ELEMENT

IN THE RELEASED POSITION

OPERATION ELEMENT

PRESSURE SPRINGS

1 2 3 4 5 6 7 8

LOOP

+ -

PCB LAYOUT & WIRING

LOOP

+ -

OUT

ADDRESS SWITCH

1 2 3 4 5 6 7 8

Figure 1: General Wiring Diagram

MAN2692-2

ACP-02 Addressable Manual Call Point Item Number: 4255-0200

Installation guide

1 2 3 4 5 6 7 8

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

116

115

117

118

119

120

121

122

123

124

125

126

127

1 2 3 4 5 6 7 8

Figure 2: Address Switch Settings

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Ampac Alarme incendie

Ampac

Ampac FireFinder PLUS Mode d’emploi

Ampac

Ampac XP95 Manuel utilisateur

Ampac

Ampac FireFinder PLUS Mode d’emploi

Ampac

Ampac ZoneSense Plus Mode d’emploi

Ampac

Ampac ACP05 Manuel utilisateur

Ampac

Ampac XP95 Manuel utilisateur

Ampac

Ampac ZoneSense PLUS Agent Release Mode d’emploi

Ampac

Ampac ZoneSense Plus Mode d’emploi

Ampac

Ampac MAN 3038 Manuel utilisateur

Ampac

Ampac 4310-0082 Manuel utilisateur

Ampac

Ampac NZ 100 Manuel utilisateur

Ampac

Ampac Warning Sign 4210-011 Manuel utilisateur

Ampac

Ampac FireFinder II Series Manuel utilisateur

Ampac

Ampac SmartTerminal Mode d’emploi

Ampac

Ampac 4210-0050 Manuel utilisateur

Ampac

Ampac ZoneSense Manuel utilisateur

Ampac

Ampac Apartment Module Manuel utilisateur

Ampac

Ampac ACP-02 Manuel utilisateur

Ampac

Ampac 4310-0086 Manuel utilisateur

Ampac

Ampac FireFinder NZS 4512 Manuel utilisateur

Ampac

Ampac ZoneSenseDH4 Mode d’emploi

Manuels Alarme incendie populaires d'autres marques

Zeta Alarm Systems

Zeta Alarm Systems INFINITY ID2 Manuel utilisateur

System Sensor

System Sensor 22051TLE-RF-26 Manuel utilisateur

Pittway

Pittway Notifier AM2020 Manuel utilisateur

Kidde

Kidde VM-1 Manuel du produit

LST

LST SIM016-3 Manuel utilisateur

Fireboy- Xintex

Fireboy- Xintex FBD-MZ Instructions originales

bolid

bolid S2000-IP-03 Manuel utilisateur

GST

GST DI-9204 Manuel utilisateur

E2S

E2S BExTBG05D Manuel utilisateur

Notifier

Notifier UZC-256 Manuel utilisateur

Fire-Lite Alarms

Fire-Lite Alarms MS-2 Manuel utilisateur

Siemens

Siemens FDOOT221 Manuel utilisateur

hyfire

hyfire HY5000 Series Manuel utilisateur

FlameStop

FlameStop PFSIFP8 Manuel utilisateur

Radionics

Radionics Radionics 9124 Manuel utilisateur

UniPOS

UniPOS FD 7120 Manuel utilisateur

FIREWOLF

FIREWOLF FW-C01224 Manuel utilisateur

Siemens

Siemens MH-5 Series Manuel de service