Amico Reflection Series Manuel utilisateur

Installation lnstructions

Reflection Series Artwall

2Amico Corporation

User Responsibility

The installation instructions provided are for the Amico standard products. Slight modifications to the installations may

be required. The product shipped to the job site may not be exactly as shown on the installation drawings. See additional

sheets for project specifics where required.

IMPORTANT: PLEASE READ CAREFULLY PRIOR TO START

• Review and understand all instructions before commencing work.

• Artwall installation should conform to the local building codes.

All on-site preparations must be done prior to the delivery of the Artwall. Please contact Amico to confirm and review all

information listed below. Failing to do so may result in discrepancies/misalignments during installation.

Please Note These Keywords and Symbols:

WARNING: Steps where extra care should be taken to prevent injuries and damage.

NOTE: Steps that point out helpful information.

IMPORTANT: Be sure to observe this instruction.

www.amico.com 3

Preparation Before Installation

1. Review a copy of the final approved shop drawing(s) and/or submittal package. These documents will provide you

with technical information specific to your installation, such as:

• Equipment types and quantities

• Room numbers and locations

• Shop drawings of each unit type

• Wiring diagrams and rough-in locations

2. Prepare the tools and hardware needed to complete the installation. Some common tools that may be required are:

• Cordless drill/driver with common drill or drive bits

• Hand tools (screwdrivers, 5/16" wrenches, clamps, pliers, etc.)

• Laser- or Bubble-level

• Ladder(s)

3. Locate the Artwall unit from the shipping boxes. The contents of each shipping box are listed on the shipping

document(s).

IMPORTANT: Before installation of the Artwall, ensure wall is framed and roughed in as per applicable building

standards to accept Artwall back box. Allow 1/8”space on each side to allow for adjustment. Back box sizes are as

follows:

• 3-gas box – 30 ⁄" w x 21 ⁄" h

• 5-gas box – 42 ⁄" w x 21 ⁄" h

O VA

AO O V

3-Gas Box

14"

[356 mm]

35"

[889 mm]

25"

[635 mm]

22 ½"

[572 mm]

31 ½"

[800 mm]

11 ½"

[292 mm]

Diagonal Movement

Request for Electrical

Devices are to be

located at only these

2 positions as shown

O VA

AO O V

5-Gas Box

12"

[305 mm]

46"

[1168 mm]

24"

[610 mm]

22 ½"

[572 mm]

44"

[1118 mm]

Diagonal Movement

10 ⁄"

[275 mm]

Request for Electrical

Devices are to be

located at only these

2 positions as shown

4Amico Corporation

1. Place the Artwall Back Box on the wall structure (See Figures 1 & 2).

IMPORTANT: Allow gap between back box flange to stud faces for drywall to be attached later (See Figure 3).

2. Attach Artwall back box to wall structure using hardware compliant to the local building codes.

NOTE: Make sure to use appropriate screw to attach the back box onto the wall structure as screws are exposed

to the end users.

Installation

Gap for Drywall

Figure 1

Figure 3

Figure 2

Wall Structure

Artwall Back

Artwall Back Box Installation on Building Studs

Artwall Setup In Place

Top View

Building Studs Facing Each Other

www.amico.com 5

Artwall secured to

the wall. Hardware

provided by others.

Art and frame attached

to the backing plate.

Hardware provided by

others.

Backing Plate

Figure 5

Figure 4

Building Studs

Remove the backing

plate to get access

for installation of

the back box

This screw can be

installed in Step 5 of

installation process

Picture Frame

Picture

Installation

3. Finish building stud framing by providing a horizontal stud on top of the Artwall.

4. Make all medical gas connections and (if applicable) electrical wiring from artwall to rough-ins. Medical gas pipes and

electrical wiring are terminated as per shop drawings.

5. Remove the frame and movement assembly from the back box.

6. Insert art into frame (if applicable) then attach frame to backing plate and movement assembly using hardware

provided by others (Figure 5).

NOTE: Ensure frame is centered on backing plate. Place assembly in a safe location.

NOTE: The weight of the picture frame shall not exceed 15 lbs.

6Amico Corporation

NOTE: At this point, it is recommended for the wall to be finished before proceeding. This will minimize

interference of unit with trades, and keep remaining parts clean.

7. Attach the frame and movement assembly that has been removed in Step 5 to back box using the original hardware

at locations shown. Move frame as necessary to reach all of the hardware..

8. Tighten whiz flange screws using a 5/16" wrench.

IMPORTANT: The frame has been removed in Figure 6 to show the parts behind it. Do not remove your frame

from the movement assembly!

Installation

Figure 6

Screw Locations (5)

www.amico.com 7

Notes

www.amico.com

Amico Corporation | 85 Fulton Way, Richmond Hill, ON L4B 2N4, Canada

600 Prime Place, Hauppauge, NY 11788, USA

Toll Free Tel: 1.877.462.6426 | Tel: 905.764.0800 | Fax: 905.764.0862

Email: info@amico.com | www.amico.com

ACAIMARTWALL 05.08.2020

C US LISTED

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Amico Équipement médical

Amico

Amico ATA-8-32 Manuel utilisateur

Amico

Amico AHM Mode d’emploi

Amico

Amico HMA-WT-LEDMNT Caractéristiques techniques

Amico

Amico ICE 25 Manuel de service

Amico

Amico Majestic Series Manuel utilisateur

Amico

Amico Roll Stand INE-0909-12-12-F4-M Manuel utilisateur

Amico

Amico ADULT 11 Manuel utilisateur

Amico

Amico ARM Instructions d'utilisation

Amico

Amico LightMaster Multifunction Switch Manuel

Amico

Amico Falcon Manuel utilisateur

Amico

Amico Falcon IT Instructions d'utilisation d'origine

Amico

Amico Apollo MS-SC Manuel

Amico

Amico Exergen 134201 Manuel du produit

Amico

Amico Mira LED Exam Light Manuel

Amico

Amico Gamma LED Series Manuel

Amico

Amico GoLift Manuel utilisateur

Amico

Amico S-M-100 Manuel

Amico

Amico CS-SLVP-ADA-00 Manuel du produit

Amico

Amico Diagnostic Station Manuel utilisateur

Amico

Amico S-AM1-300X Manuel

Amico

Amico AC-200C Manuel d'installation et d'exploitation

Amico

Amico ALERT- 2 Manuel

Amico

Amico Mira LED Exam Light Manuel

Amico

Amico S-H-300 Manuel

Manuels Équipement médical populaires d'autres marques

TekTone

TekTone Tek-CARE160 Manuel utilisateur

NeuroMetrix

NeuroMetrix Quell 2.0 Manuel utilisateur

AMT

AMT XLR8 Manuel utilisateur

Medipost-Nutristoma

Medipost-Nutristoma MD300K2 Manuel utilisateur

EDAN

EDAN SONOTRAX Pro Manuel utilisateur

Restorative Therapies

Restorative Therapies RT300 Manuel utilisateur

Gendex

Gendex Expert DC Manuel utilisateur

Dexcowin

Dexcowin ADX4000W Manuel utilisateur

Libelium

Libelium MySignals Manuel utilisateur

Acelity

Acelity V.A.C.ULTA 4 Manuel utilisateur

Caputron

Caputron ActivaDose II tDCS Manuel utilisateur

FujiFilm

FujiFilm Sonart Manuel du propriétaire

Plinth 2000

Plinth 2000 93CDT Manuel utilisateur

GE SENOGRAPHE 800T Manuel utilisateur

GE Definium 5000 Manuel utilisateur

Kanmed

Kanmed GE-1380 Manuel utilisateur

Huntleigh

Huntleigh FD1 Manuel utilisateur

Stryker

Stryker SPR Plus Manuel utilisateur