AMFLOW A3 Manuel utilisateur
A & H Enterprises, Inc.
11812 NE 116th Street
TEL:
+425.883.4040
Kirkland, WA 98034 USA
FAX:
+425.823.1962
www.amflow.com
EMAIL:
QUICK START: H1 WIRING
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. D, 07/16
Page 1 of 16
Amflow®
AMFLOW®
A3 VALVE ACTUATOR
A3 Quick Start: H1
CONTENTS
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. D, 07/16
Page 2 of 16
AMFLOW®
Contents
1. What is Included
2. Installation: Actuator
3. Installation: Valve
4. Wiring: H1
5. Caution Information
6. Safety Information
7. Support
8. Representatives
A3 Quick Start: H1
WHAT IS INCLUDED
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. D, 07/16
Page 3 of 16
AMFLOW®
What is included with your Amflow®product?
☐ACTUATOR: A3-ACM
Actuator
Adjustment Handle
Adjustment Handle Mounting Screw & Lockwasher
Installation Manual & Service Manual
A3 Quick Start: H1
INSTALLATION
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. D, 07/16
Page 4 of 16
AMFLOW®
Installation: Actuator
Step 1
Cut-out panel for mounting
A3 Quick Start: H1
INSTALLATION
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. D, 07/16
Page 5 of 16
AMFLOW®
Step 2
Attach actuator base plate assembly to front of panel.
Step 3
Mount actuator to base plate assembly using M8 SHCS.
A3 Quick Start: H1
INSTALLATION
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. D, 07/16
Page 6 of 16
AMFLOW®
Step 4
Prior to installing valve, confirm handle is in manual
position.
AUTOMATION MODE
(Handle at Side)
MANUAL MODE
(Handle at Front)
A3 Quick Start: H1
INSTALLATION
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. D, 07/16
Page 7 of 16
AMFLOW®
Valve Shaft
Adaptor
(4) Cam Lock Screws
Installation: Valve
Step 5
Install Valve Shaft Adaptor into AM30 flow control valve.
A3 Quick Start: H1
INSTALLATION
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. D, 07/16
Page 8 of 16
AMFLOW®
Step 6
Thread flow control valve to actuator through back of panel
Step 7
Align anchor studs on AM30 flow control valve with mating holes
in A3 Valve Actuator
Step 8
Slowly rotate adjustment handle to align drive pins in valve
actuator with Valve Shaft Adaptor to seat valve to actuator.
Step 9
Lock in place with Cam Lock Screws.
A3 Quick Start: H1
WIRING
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. D, 07/16
Page 9 of 16
AMFLOW®
ACTUATOR WIRING: H1
Step 1
Provide 24VDC supply capable of providing up to 3 amps
current.
Step 2
Requires a minimum of 5 connections for H-1 operation.
Step 3
Requires a minimum of 9 connections for set-up , Industrial
Ethernet and H-1 communication.
Terminal block wiring reference for field connections
WARNING
Incorrect wiring may damage the unit!
A3 Quick Start: H1
COMMUNICATIONS
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. D, 07/16
Page 10 of 16
AMFLOW®
H1 COMMUNICATION SET-UP
CAUTION
Parameters are pre-set at the manufacturer.
Step 1
Connect Industrial Ethernet cable between actuator and DHCP
server or DHCP router
Step 2
Launch flash enable internet web browser.
Step 3
Type in web address found on actuator.
Step 4
Follow set-up procedures.
NOTE
DHCP “Dynamic Hosting Configuration Protocol” is a method that automatically
assigns IP addresses to devices connected to a network without manually
configuring everything connected to a computer or server. Due to the wide variety of
computers, networks, servers, routers and operating systems, a “DHCP” device is
highly recommended for a quick and easy set-up. The “DHCP” device is either a
server or router depending upon the end users network configurations.
If an end user is manually configuring their network, they should contact their IT
department.
Table des matières
Autres manuels AMFLOW Contrôleurs
