AMERITECH AM100 Manuel utilisateur

AM100

SECURITY SYSTEM

INSTALLATION

INSTRUCTIONS

N7526-3V1 Rev B 4/99 Ref: 20AMTE

–2–

RECOMMENDATIONS FOR PROPER PROTECTION

The Following Recommendations For The Location Of Fire And Burglary Detection

Devices Help Provide Proper Coverage For The Protected Premises.

Recommendations For Smoke And Heat Detectors

With regard to the number and placement of smoke/heat detectors, we subscribe to the

recommendations contained in the National Fire Protection Association's (NFPA) Standard #72

noted below.

Early warning fire detection is best achieved by the installation of fire detection equipment in all

rooms and areas of the household as follows: For minimum protection a smoke detector should be

installed outside of each separate sleeping area, and on each additional floor of a multi-floor

family living unit, including basements. The installation of smoke detectors in kitchens, attics

(finished or unfinished), or in garages is not normally recommended.

For additional protection the NFPA recommends that you install heat or smoke detectors in the

living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage

rooms, basements and attached garages.

In addition, we recommend the following:

• Install a smoke detector inside every bedroom where a smoker sleeps.

• Install a smoke detector inside every bedroom where someone sleeps with the door partly or

completely closed. Smoke could be blocked by the closed door. Also, an alarm in the hallway

outside may not wake up the sleeper if the door is closed.

• Install a smoke detector inside bedrooms where electrical appliances (such as portable

heaters, air conditioners or humidifiers) are used.

• Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet (12

meters) long.

• Install smoke detectors in any room where an alarm control is located, or in any room where

alarm control connections to an AC source or phone lines are made. If detectors are not so

located, a fire within the room could prevent the control from reporting a fire or an intrusion.

THIS CONTROL COMPLIES WITH NFPA REQUIREMENTS FOR TEMPORAL PULSE

SOUNDING OF FIRE NOTIFICATION APPLIANCES.

DINING KITCHEN BEDROOM

BEDROOM

LIVING ROOM

✪

✪✪

✪

▲

BEDROOM

DINING

LIVING ROOM

TV ROOM KITCHEN

■■■

✪

✪▲

✪

BEDROOM BEDROOM

■

■▲

Smoke Detectors for Minimum

Smoke Detectors for Additiona

Heat-Activated Detectors

Recommendations For Proper Intrusion Protection

For proper intrusion coverage, sensors should be located at every possible point of entry to a home or

commercial premises. This would include any skylights that may be present, and the upper windows

in a multi-level building.

In addition, we recommend that radio backup be used in a security system so that alarm signals can

still be sent to the alarm monitoring station in the event that the telephone lines are out of order

(alarm signals are normally sent over the phone lines, if connected to an alarm monitoring station).

–3–

TABLE OF CONTENTS

Section 1. GENERAL DESCRIPTION .................................................................................................. . 7

Section 2. INSTALLING THE CONTROL.............................................................................................10

Mounting the Cabinet ........................................................................................................10

Installing the Lock (if used) ..............................................................................................10

Mounting the Control's Circuit Board Alone in the Cabinet............................................11

Mounting Control and RF Receiver Circuit Boards Together in the Cabinet.................11

Standard Phone Line Connections....................................................................................12

Wiring the AC Transformer...............................................................................................12

Installing the Back-Up Battery.........................................................................................13

Earth Ground Connections ................................................................................................13

Section 3. INSTALLING REMOTE KEYPADS.....................................................................................14

Keypads That May Be Used...............................................................................................14

Wiring The Keypads.......................................................................................................... .14

Mounting The Keypads..................................................................................................... .15

Using A Supplementary Power Supply To Power Additional Keypads .......................... 15

Preliminary Check-Out Procedure....................................................................................16

Section 4. BASIC HARD-WIRED ZONES 1–8.....................................................................................17

Installing the Hard-Wired Zones.......................................................................................17

Common Characteristics For Zones 1–8 ....................................................................... .17

Wiring Burglary and Panic Devices to Zones 1–8.........................................................17

Wiring 2-Wire Smoke Detectors to Zone 1.....................................................................17

“Verify” Operation of 2-Wire Smoke Detectors in Zone 1 .............................................17

Turning Off Fire Alarm Sounding..................................................................................18

Wiring 4-Wire Smoke/Combustion Detectors on Zones 2–7..........................................18

Wiring 2-Wire Latching Type Glass Break Detectors on Zone 8..................................19

Check-Out Procedure for Hard-Wired Zones ....................................................................20

Section 5. WIRED ZONE EXPANSION (4219, 4229)...........................................................................21

Installing Zone Expansion Units.......................................................................................21

Connections and Set-Up................................................................................................. .21

Check-Out Procedure for Wired Expansion Zones............................................................22

Section 6. WIRELESS ZONE EXPANSION (5800 SYSTEM)..............................................................23

General Information.......................................................................................................... .23

Receiver Supervision...................................................................................................... .23

House Identification........................................................................................................23

Installing the 5881/5882 RF Receiver...............................................................................23

RF System Installation Advisories.................................................................................23

Installation and Set-Up of the 5881/5882 Receiver.......................................................24

Installing the 5800TM Module ..........................................................................................25

Mounting the 5800TM Module.......................................................................................25

5800TM Wiring Connections ......................................................................................... .25

5800 Series Transmitters.................................................................................................. .25

General............................................................................................................................ .25

Transmitter Supervision.................................................................................................25

Transmitter Input Types ................................................................................................26

Transmitter Battery Life ................................................................................................26

Using the Transmitter Sniffer Mode.................................................................................26

5800 Series Transmitters Table.........................................................................................27

Section 7. RELAY OUTPUTS & POWERLINE CARRIER DEVICES ..................................................29

Relay/Powerline Carrier Device Basics.............................................................................29

Nos. 4204 And 4229 Output Relay Modules .....................................................................29

4204/4229 Setup.......................................................................................................... .29

Powerline Carrier Devices................................................................................................. .30

Wiring Connections..................................................................................................... .31

–4–

Section 8. 4285 & 4286VIP PHONE MODULES ................................................................................ .32

Installing the Phone Module..............................................................................................32

General Information........................................................................................................32

Mounting The Phone Module ........................................................................................ .32

Phone Module Wiring..................................................................................................... .33

Caller ID Units............................................................................................................... .33

Checking the Operation of the 4285 or 4286 Phone Module............................................35

Section 9. EXTERNAL SOUNDERS.................................................................................................... .36

Compatible Sounders..........................................................................................................36

Sounder Connections..........................................................................................................37

Testing the Sounder.......................................................................................................... .37

Section 10. LONG RANGE RADIO ........................................................................................................38

General Information.......................................................................................................... .38

Connection ..........................................................................................................................38

Section 11. REMOTE KEYSWITCH ...................................................................................................... .39

Installing the Keyswitch .................................................................................................. .39

Remote Keyswitch Connections......................................................................................39

Programming for the Remote Keyswitch ..........................................................................41

Keyswitch Operation...................................................................................................... .42

Section 12. AUDIO ALARM VERIFICATION (AAV) UNIT.....................................................................43

General Information.......................................................................................................... .43

Wiring Connections ........................................................................................................... .43

Section 13. FINAL POWER UP..............................................................................................................45

Earth Ground Connections ................................................................................................45

Connecting the Back-Up Battery.......................................................................................45

Calculating the Battery Size Needed.............................................................................45

Making the Battery Connections....................................................................................46

Auxiliary Device Current Draw Worksheet......................................................................46

Section 14. MECHANICS OF PROGRAMMING....................................................................................47

General Programming Information...................................................................................47

Entering Program Mode.....................................................................................................47

Programming a Data Field.................................................................................................47

Reviewing a Data Field/Erasing an Entry in a Data Field .............................................. 48

Interactive Mode Programming (✱56, ✱80, ✱82, and ✱83).............................................. 48

Loading Factory Defaults.................................................................................................. .48

Programming System Setup Fields...................................................................................48

Exiting the Programming Mode ........................................................................................48

Section 15. ZONE RESPONSE TYPE DEFINITIONS............................................................................49

Section 16. DATA FIELD DESCRIPTIONS............................................................................................51

Section 17. ZONE PROGRAMMING (✱56 Menu Mode) .......................................................................61

Section 18. OUTPUT DEVICES (✱80 Menu Mode)...............................................................................65

Section 19. ZONE LISTS (✱81 Menu Mode) .........................................................................................69

Section 20. ALPHA DESCRIPTOR PROGRAMMING (✱82 Menu Mode) ............................................70

Zone Descriptors.................................................................................................................70

Programming Zone Descriptors (program Menu Mode ✱82)...........................................70

Adding Custom Words........................................................................................................73

Alpha Vocabulary List (For Entering Zone Descriptors) .................................................74

Character (ASCII) Chart....................................................................................................74

Section 21. USING SEQUENTIAL MODE (✱83 Menu Mode) ..............................................................75

Section 22. REMOTE PROGRAMMING AND CONTROL (DOWNLOADING)......................................78

General Information.......................................................................................................... .78

Equipment Required ..........................................................................................................78

Initial Download .................................................................................................................78

–5–

Remote Programming Information....................................................................................79

Remote Programming Advisory Notes ..............................................................................79

Section 23. SYSTEM COMMUNICATION ............................................................................................ .80

Report Code Formats..........................................................................................................80

Table of Contact ID Codes................................................................................................. .82

Section 24. SYSTEM OPERATION........................................................................................................83

Security Codes................................................................................................................... .83

Keypad Functions.............................................................................................................. .84

Trouble Conditions .............................................................................................................86

Section 25. TESTING THE SYSTEM..................................................................................................... .87

Test Procedure................................................................................................................... .87

To the Installer...................................................................................................................88

Section 26. TROUBLESHOOTING GUIDE ............................................................................................89

Contacting Technical Support In The Event Of Problems...............................................91

REGULATORY AGENCY STATEMENTS..........................................................................92

Section 27. SPECIFICATIONS & ACCESSORIES ................................................................................93

Specifications ......................................................................................................................93

Accessories (Compatible Devices)......................................................................................95

APPENDIX A. 5800 RF System Wireless Transmitters, Input Loop Identification Diagrams............ 96

Index.......................................................................................................................................................... .97

Limitations Of This Alarm System ...................................................................................................... . 102

Summary Of Connections.................................................................................................................... . 103

Limited Warranty .......................................................................................................................Back Cover

Programming Form ............................................................................................................................Insert

LIST OF FIGURES

Figure 1. Installing the Cabinet Lock ...............................................................10

Figure 2. Mounting The PC Board ....................................................................11

Figure 3. Mounting the PC Board & RF Receiver Together in the Cabinet ...11

Figure 4. Telephone Line Connections..............................................................12

Figure 5. Connection of 4300 Transformer to the Control Board.................... 13

Figure 6. Keypad Connections to the Control Board........................................15

Figure 7. Using a Supplementary Power Supply .............................................16

Figure 8. 2-Wire Smoke Detector Connected to Zone 1....................................18

Figure 9. 4-Wire Smoke Detector Connections (Zones 2–7)............................. 18

Figure 10. Glass Break Detector Connections to Zone 8....................................19

Figure 11. Wiring Connection, 4219 & 4229 (4229 shown) ................................21

Figure 12. 5881/5882 RF Receiver (cover removed) ...........................................24

Figure 13. 4229 Connections To Control.............................................................30

Figure 14. 4204 Connections To Control.............................................................30

Figure 15. 4300 Transformer Wiring Connections.............................................31

Figure 16. 4285/4286 Phone Module Wiring Connections .................................34

Figure 17. Typical Sounder Wiring .....................................................................37

Figure 18. Long Range Radio Connections........................................................38

Figure 19A. Keyswitch Wiring (4300 Interface Transformer not used) ..............40

Figure 19B. Keyswitch Wiring (4300 Interface Transformer also used)............. 40

Figure 20. Connection of AAV Unit When Not Using a 4285 Phone Module..44

Figure 21. Connection of AAV Unit When Also Using a 4285 Phone Module.44

Figure 22. AM100 Summary of Connections ..................................................103

–6–

CONVENTIONS USED IN THIS MANUAL

MAIN SECTION TITLES ARE SHOWN IN REVERSE TYPE

Before you begin using this manual, it is important that you understand the

meaning of the following symbols (icons).

ULThese notes include specific information which must be followed if you are

installing this system for a UL Listed application.

These notes include information that you should be aware of before continuing

with the installation, and which, if not observed, could result in operational

difficulties.

This symbol indicates a critical note that could seriously affect the operation of

the system, or could cause damage to the system. Please read each warning

carefully. This symbol also denotes warnings about physical harm to the

installer.

✱20 INSTALLER CODE

In the text of this manual, basic programming data fields are indicated by a

“star” [✱] followed by the data field number (and its title in many cases).

Enter Zn Num.

(00 = Quit) 01

In the text of this manual, interactive programming prompts

are shown in a double-line box (e.g., Menu Mode ✱56 for Zone

Programming).

PRODUCT MODEL NUMBERS: Unless noted otherwise, references to specific

model numbers represent Ademco products.

Whenever it becomes necessary to disconnect power in order to add a module

or keypad, always disconnect the battery and then the AC transformer in that

order. After installation has been completed, connect the AC transformer first

followed by connection of the battery.

–7–

Section 1. GENERAL DESCRIPTION

The AM100 is a security system control that supports up to 38 zones, using basic hard-wired,

wired expansion, and/or wireless zones, plus 3 keypad activated zones.

Basic Hardwired Zones

Provides 8 basic hardwired zones having the following characteristics:

• EOLR supervision supporting N.O. or N.C. sensors

• Programmable response time (10, 350, or 700 milliseconds)

• Up to sixteen 2-wire smoke detectors on zone 1

• 4-wire smoke or heat detectors on zones 2 through 7 (as many as can be

powered from AUX power on the control)

• Up to fifty 2-wire latching type glassbreak detectors on zone 8 with

auto reset

Optional Expansion Zones (up to 30 total, wired and wireless)

Wired Expansion:

Supports up to 8 additional wired zones using a 4219 expansion module or

4229 expansion/relay module. These zones have the following

characteristics:

• EOLR supervision supporting N.O. or N.C. sensors

• 300–500 msec normal response with an option for fast (10–15 msec)

response on loop A (first expansion zone)

Wireless Expansion:

Supports up to 30 wireless zones (less if using wired expansion zones).

• Requires the use of a 5881(5882 in Canada) type RF Receiver, as

indicated below

Receiver Model No. of Zones

5881L/5882L Up to 8

5881M/5882M Up to 16

5881H/5882H Up to 30

• Requires the use of 5800 series wireless transmitters

Remote Keypads Up to 8 of any of the following keypads may be used in the installation:

Fixed-Word Keypad: AM6128

Alpha Keypad: AM6139 (2-line alphanumeric display)

For programming from a keypad, a AM6139 2-line Alpha keypad must be

connected, but need not remain in the system after programming has been

completed.

–8–

Security Codes • One installer code for entire system (user 1)

• One Master code for entire system (user 2)

• 12 secondary user codes (users 3–14)

• One baby-sitter code (user 15)

• One duress code (user 16)

Baby-sitter Code: A special code that can only be used to disarm the system if

that particular code (or the installer code) was used to arm it.

Duress Code: An emergency code which, when entered by

any

user to disarm

or arm the system, will send a silent duress message to the central station.

Keypad Panic Keys

•Up to 3 programmable panic key functions are provided.

•Designated as Zones 95, 96, 99

•Activated by wired & wireless keypads

• Distinguished by subscriber ID number

Zone Monitor Feature

• The control will sense a high resistance in the loops on hard-wired

zones 2–8 if it is present, and will display a trouble message (rather

than an alarm) for the affected zone when the system is in the disarmed

mode. This feature also prevents the system from being armed while

this high resistance condition exists.

Exit Error False Alarm Prevention Feature

• Enables the system to determine the difference between an actual

alarm and an alarm caused by leaving an Entry/Exit or Interior zone

open after the exit delay expires. If not disarmed in time, an alarm will

sound and an “Exit Error” report sent to the central station.

• An Exit Alarm condition will also occur if an Entry/Exit or Interior zone

re-opens within 2 minutes after the end of an exit delay.

Optional Output Relays and Powerline Carrier Devices (X-10 type)

• Up to 4 relays using one 4204 Relay Module

• Up to 2 relays using one 4229 Zone/Relay Module

• Up to 8 Powerline Carrier devices (you must subtract the number of

relay outputs actually used by the 4204 or 4229 modules, if used)

• Actions programmable to respond to zone activity or manual keypad

entries

Powerline Carrier devices require the use of optional 4300 transformer module

instead of the supplied 1321 AC transformer.

Optional Phone Module

• Supports the Ademco 4285/4286 Phone Module

• Provides access to the system via on premises or off-premises phones

for arming, disarming, etc., plus control of relay outputs and Powerline

Carrier devices.

Paging Feature • If programmed, the paging feature permits up to 16-digits to be sent to

a pager for user-determined messaging, followed by a system

generated 7-digit condition code which indicates the type of condition

that has occurred and the user number or zone number of occurrence.

Audio Alarm Verification Option

• Provides a programmable Audio Alarm Verification (AAV) option which

can be used in conjunction with an output relay to permit voice dialog

between an operator at the central station and a person at the premises.

• Requires the use of optional AAV unit, such as Eagle model 1241.

ULThe AAV option may not be used in UL installations.

–9–

Optional Long Range Radio

• Allows all messages that have been programmed to go to the primary

telephone number to be reported additionally to a 7720PLUS or 7820

radio. Check availability of these models.

Built-in Telephone Line Monitoring Option

•The telephone line voltage can be monitored to supervise the phone line

connection. The panel must be connected to a proper earth

ground or you will get a false line cut indication if this feature

is enabled.

• The loss of the line can optionally cause a local display, or a display and

trouble sound.

Event Logging •Event Logging feature keeps a record of selected events in a history log

(up to 48 events). All control and readout from the log is done via

Ademco V-Link software only.

Alarm Output •Provides a 12VDC, 2 AMP output that can drive the compatible

sounders listed in the EXTERNAL SOUNDERS section (assumes a fully

charged battery is connected).

• Steady output for Burglary/Panic, or temporal pulse output (3 pulses –

pause – 3 pulses – pause – 3 pulses. . .) for Fire.

• Uses current limiting circuitry for protection.

Auxiliary Power Output

• Provides 12VDC, 600 mA maximum. Uses current limiting circuitry for

protection.

• This output interrupts for smoke detector reset if 4-wire smoke

detectors are used.

Programming • Programmed options are stored in electrically erasable, non-volatile

EEPROM memory (information can be reprogrammed at any time and

will not be lost in the event of a power loss).

• The system can be uploaded, downloaded, or controlled via an IBM

compatible computer, V-Link software and a HAYES modem specified

by Ademco.

Keypad programming consists of:

• Data field programming

• Interactive (menu) mode programming

Communication Formats Supported

• Ademco Low Speed (Standard or Expanded)

• Sescoa/Radionics (Standard or Expanded)

• Ademco Express

• Ademco Contact ID

Zone Descriptors You can assign Alpha descriptors to all zones (useful only when using

Alpha keypads and/or the 4285/4286 Phone Module).

AC Power SupplyUses 1321, 110VAC plug-in transformer with 16.5VAC 25VA output,

unless Powerline Carrier devices (ex. X-10 type) are used, in which case a

4300 transformer module must be used.

Back-Up Battery • Rechargeable (Gel type) 12VDC, 4AH minimum.

–10–

Section 2. INSTALLING THE CONTROL

This section provides instructions for mounting the control cabinet and

installing the cabinet lock (if used). Also included in this section are

instructions for the following:

• Installing the main PC board

• Mounting the 5881 (5882 in Canada) RF Receiver board in the cabinet (if

used)

• Standard phone line connections

• Installing the back-up battery in the cabinet

• Connecting the AC transformer

• Making earth ground connections

Mounting the Cabinet

Mount the control cabinet to a sturdy wall using fasteners or anchors (not

supplied), in a clean, dry area which is not readily accessible to the general

public. Four mounting holes are provided at the back of the cabinet.

If an RF Receiver is being used and you intend to mount its PC board within

the cabinet, note the following:

• Do not mount the cabinet on or near metal objects. This will decrease

RF range and/or block RF transmissions from wireless transmitters.

• Do not locate the cabinet in an area of high RF interference (revealed by

frequent or prolonged lighting of the LED in the receiver after it is

operational (random flicker is OK).

Installing the Lock (if used)

Use an Ademco No. N6277 Cam Lock and No. N6277–1 Push-On Clip

(Retainer Clip).

Note: The cabinet can be closed and secured without a lock by using 2

screws in the cover's edge.

CABINET DOOR BOTTOM

RETAINER

CLIP

RETAINER CLIP

(NOTE POSITION)

RETAINER

SLOTS

LOCKED

UNLOCKED

Figure 1. Installing The Cabinet Lock

1. Remove the cabinet door. It

is easily removable for

servicing and is easily re-

installed.

2. Remove the lock knockout

from the control cabinet door.

Insert the key into the lock.

Position the lock in the hole

making certain that the latch

will make contact with the

latch bracket when the door is

closed.

3. Hold the lock steady, and

insert the retainer clip into

the retainer slots. Position

the clip as illustrated in order

to permit easy removal.

Before installing the cabinet's contents, remove the metal cabinet

knockouts required for wiring entry. Do not attempt to remove the

knockouts after the circuit board has been installed.

Autres manuels pour AM100

Table des matières

Autres manuels AMERITECH Système de sécurité

AMERITECH

AMERITECH AM100 Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur