American Dynamics RAS915 Manuel utilisateur

SPEEDDOME ULTRA VII CAMERA DOME CONFIGURATION UTILITY 8200-0184-09, REV. A

OPERATOR’S MANUAL SUPPLEMENT 1 of 13

SpeedDome®Ultra VII

Camera Dome

Configuration Utility

Operator’s Manual Supplement

RAS915/RAS916/RAS917 Series

Contents

About this Supplement.......................................... 1

New SpeedDome Ultra VII Features..................... 1

Quick Set Menu..................................................... 2

Auto Iris/Auto Focus Resume Setting................... 3

Scan Limits............................................................ 4

AD Up-the-Coax Protocol...................................... 5

SensorNet and RS-422 Matrix Switchers and

Controllers........................................................ 6

Panasonic UTC Protocol Preset Programming..... 9

Specifications-SDU VII........................................ 10

Specifications-22X Camera................................. 11

Specifications-23X Day/Night Camera................ 12

Declarations ........................................................ 13

About this Supplement

This supplement provides detailed information

about SpeedDome Ultra VII camera dome features

that are not currently covered in your operator’s

manual. This supplements information found in the

following manuals:

• 22x Camera Dome Configuration Utility

Operator’s Manual, 8200-0184-02

• Day/Night Camera Dome Configuration Utility

Operator’s Manual, 8200-0184-04

NOTE: Keep this supplement with your operator’s

manual for reference purposes.

If you need assistance...

Contact your Sales Representative.

New SpeedDome Ultra VII

Features

SpeedDome Ultra VII provides the following

features with firmware version 0710-0147-0106

and newer.

• Quick Set Menu for accessing commonly used

dome settings

• Auto Iris/Auto Focus resume settings

• Scan Limits for establishing start and stop points

for monitoring a specific area

• AD Up-the-Coax protocol for compatible

American Dynamics controllers

In addition, updated information is provided for the

following:

• SensorNet and RS-422 matrix switchers and

controllers

• Preset programming instructions for the

Panasonic WJ-SX550 multiplexer and

WV-CU550A controller

SPEEDDOME ULTRA VII CAMERA DOME CONFIGURATION UTILITY 8200-0184-09, REV. A

OPERATOR’S MANUAL SUPPLEMENT 2 of 13

Quick Set Menu

The Quick Set Menu provides easy access to

commonly used SpeedDome Ultra VII features

when used with compatible controllers. This allows

you to change or activate features without starting

the dome configuration menu. The options on the

Quick Set Menu differ depending on the dome

type. See Figure 1 and Figure 2 for examples of

the different menus.

Figure 1: 22x Camera Dome Quick Set Menu

0 TOGGLE QUICK SET MENU

1 DOME CONFIG MENU

2 AUTO IRIS/AUTO FOCUS

3 FLIP

4 PEEL PATTERN

15 SMOOTH SCAN

16 STEPPED SCAN

17 RANDOM SCAN

20 DOME INFORMATION

Figure 2: Day/Night Camera Dome Quick Set

Menu (2 screens)

0 TOGGLE QUICK SET MENU

1 DOME CONFIG MENU

2 AUTO IRIS/AUTO FOCUS

3 FLIP

4 PEEL PATTERN

10 NIGHT MODE

11 DAY MODE

12 AUTO DAY/NIGHT MODE

13 WDR ON

14 WDR OFF

FOCUS FAR = next page

15 SMOOTH SCAN

16 STEPPED SCAN

17 RANDOM SCAN

20 DOME INFORMATION

FOCUS NEAR = previous page

To access a feature on the menu, enter the

number and press the Quick Set button (varies by

controller). Table 1 provides a description of the

available options.

Table 1: Quick Set Menu Options

Command Description

0+Quick Set Toggle Quick Set Menu: Toggles

between displaying and hiding

the quick set menu.

1+Quick Set Dome Config Menu: Displays the

SpeedDome Ultra configuration

menu.

2+Quick Set Auto Iris/Auto Focus: Resumes

Auto Focus/Auto Iris mode.

3+Quick Set Flip: Rotates the SpeedDome

180° from its current pointing

direction. This is the same as

pressing the Flip button on

compatible controllers.

4+Quick Set Peel Pattern: Runs the default

Apple Peel Pattern. This is the

same as pressing the Peel button

on compatible controllers.

10+Quick Set* Night Mode: Sets the dome IR

mode setting to ON. The dome

switches to full-time black-and-

white (B/W) mode.

11+Quick Set* Day Mode: Sets the dome IR

mode setting to OFF. The dome

switches to full-time color mode.

12+Quick Set* Auto Day/Night Mode: Resumes

the most recently selected

automatic IR mode setting.

• Auto High: B/W mode activates

~30 lux.

• Auto Mid: B/W mode activates

~3 lux.

• Auto Low: B/W mode activates

~ 0.5 lux

13+Quick Set* WDR On: Enables Wide Dynamic

Range (WDR). Use this setting

when both bright and low light

areas need to be viewed

simultaneously.

*Menu items 10-14 are available on Day/Night

domes only.

SPEEDDOME ULTRA VII CAMERA DOME CONFIGURATION UTILITY 8200-0184-09, REV. A

OPERATOR’S MANUAL SUPPLEMENT 3 of 13

Command Description

14+Quick Set* WDR Off: Disables Wide

Dynamic Range (WDR). Use this

setting when the light level is

constant or changes in lighting

conditions are gradual.

15+Quick Set Smooth Scan: Initiates a smooth

scan between the left and right

scan limits, starting at the left

scan limit. If no scan limits have

been set, initiates a smooth 360°

clockwise rotation around the

dome axis using the current tilt,

zoom and focus settings.

16+Quick Set Stepped Scan: Initiates a scan

between the left and right scan

limits pausing briefly every 10° (at

1x zoom), starting at the left scan

limit. When the right scan limit is

reached, the scan is reversed. If

no scan limits have been set,

initiates a clockwise rotation

around the dome axis pausing

briefly every 10° (at 1x zoom) for

3 seconds using the current tilt,

zoom and focus settings.

17+Quick Set Random Scan: Initiates a scan

between the left and right scan

limits pausing randomly between

the limits. If no scan limits have

been set, initiates a clockwise or

counter-clockwise rotation around

the dome axis using the current

tilt, zoom and focus settings. The

dome pauses randomly as it

rotates around the axis.

20+Quick Set Dome Information: Displays the

Dome Information screen

available through the dome

configuration menu.

Refer to your controller manual to determine if the

Quick Set Menu feature is supported. For more

information about these settings, see your

SpeedDome Ultra VII Configuration Utility

Operator’s Manual. See also:

Topic Page

Auto Iris/Auto Focus Resume Setting 3

Scan Limits 4

AD Up-the-Coax Protocol 5

SensorNet and RS-422 Matrix

Switchers and Controllers 6

Auto Iris/Auto Focus

Resume Setting

Normally, the camera’s iris and focus settings

return to automatic mode when the dome moves a

minimum of one frame from its current pointing

position. In some situations, you may want to

maintain specific iris and/or focus adjustments

based upon your surveillance needs.

Use the I/F Return to Auto setting on the

Pan/Tilt/Zoom/Sync Opts menu to configure the

auto iris and auto focus resume settings.

Figure 3: Pan/Tilt/Zoom/Sync Options menu

PROPORTIONAL FLIP OFF/ON

1ST ZOOM STOP X 33/22

MAX TOTAL ZOOM X 44...242

LINE LOCK ON/OFF

FREEZE FRAME OFF/ON

I/F RETURN TO AUTO OFF/ON/

IRIS/FOCUS

Four settings are available: On, Off, Iris and Focus.

Setting Description

On Both return to auto iris and return to

auto focus settings are enabled.

Moving the dome resumes auto mode

for both iris and focus changes.

Off Both return to auto iris and return to

auto focus settings are disabled.

Moving the dome does not resume

auto mode for iris and focus changes.

Iris Only return to auto iris is enabled.

Return to auto focus is disabled.

Moving the dome resumes auto iris

mode without changing focus settings.

Focus Only return to auto focus is

enabled. Return to auto iris is

disabled. Moving the dome resumes

auto focus mode without changing iris

settings.

Continue with Changing the Auto Iris/Auto Focus

Resume Setting on page 4 to configure the setting.

SPEEDDOME ULTRA VII CAMERA DOME CONFIGURATION UTILITY 8200-0184-09, REV. A

OPERATOR’S MANUAL SUPPLEMENT 4 of 13

Changing the Auto Iris/Auto

Focus Resume Setting

Refer to the SpeedDome Ultra VII Operator’s

Manual for information about displaying menus and

changing settings.

1. Select Pan/Tilt/Zoom/Sync Opts from the

Dome Configuration Menu.

2. Move the highlight bar to I/F Return to Auto.

Change the setting.

• Select On to enable both resume auto iris

and resume auto focus.

• Select Off to disable both resume auto iris

and resume auto focus.

• Select Iris to enable resume auto iris only.

• Select Focus to enable resume auto focus

only.

The default setting is On.

3. Select Exit to return to the Dome Configuration

Menu.

Scan Limits

Scan Limits are two points around the dome’s pan

axis, which define a surveillance area. When

active, the scan repeats until interrupted by a

camera command, preset, pattern, or alarm.

Figure 4 provides an example of scan limits for a

dome installed over the edge of a building

monitoring a parking lot. In this example, the

building blocks part of the dome’s viewable area.

Figure 4: Scan Limits example

The dashed circle represents the dome’s field of

view. The solid line curve represents the scan

area. By setting the left and right scan limits where

the building’s wall becomes visible, you ensure that

only useful video of the parking lot is being

observed when the scan is active. Once these

scan limits are programmed you can choose to run

a smooth scan, stepped scan, or random scan.

Table 2: Scan Types

Smooth Scan An automated scan that slowly

pans between the left and right

scan limits, starting at the left

scan limit. When the right scan

limit is reached, the scan

reverses.

Stepped Scan An automated scan that pans

slowly pausing briefly every 10°

between the left and right scan

limits. Once the right scan limit

is reached, the scan reverses.

Random Scan An automated scan that pans

randomly between the left and

right scan limits, starting at any

point between the scan limits.

If your controller supports the Quick Set menu

function, you can program left and right scan limits

to automate your surveillance activities. The Scan

Limits menu option is found on the Alarms/Areas/

Home/Presets/PZ menu.

Figure 5: Alarms/Areas/Home/Presets/Privacy

Zones menu

ALARMS/AREAS/HOME/PRESETS/PZ

SET ALARM ACTIONS

SET ALARM STATES

SET HOME POSITION

SET NORTH POSITION

AREA BOUNDARIES

PRIVACY ZONES

PRESETS

SCAN LIMITS

EXIT

Continue with Programming Scan Limits on page 5

to configure the setting.

Left Scan

Limit

Right Scan

Limit

Dome

Building

SPEEDDOME ULTRA VII CAMERA DOME CONFIGURATION UTILITY 8200-0184-09, REV. A

OPERATOR’S MANUAL SUPPLEMENT 5 of 13

Programming Scan Limits

Refer to the SpeedDome Ultra VII Operator’s

Manual for information about displaying menus and

changing settings.

1. Select Alarms/Areas/Home/Presets/PZ from

the Dome Configuration Menu.

2. Select Scan Limits.

The Scan Limits screen appears:

SCAN LIMITS

PAN to LEFT limit

ZOOM to mark BOUNDARY

Cancel RIGHT limit to Delete

CANCEL

Note: Press Focus during steps 3 or 4 to cancel

scan limit programming.

3. Adjust the pan position of the dome to set the

left scan limit. Press Zoom to select.

4. Pan the dome to the right to set the right scan

limit. Press Zoom to select.

5. When the Alarms/Areas/Home/Presets/PZ

screen appears, select Exit to return to the

Dome Configuration Menu.

AD Up-the-Coax Protocol

The AD Up-the-Coax (AD-UTC) protocol is a new

protocol developed by American Dynamics. It

provides video and two-way dome control signals

on a single cable for compatible American

Dynamics switchers and keyboards.

Note: At the time of publication, the following

American Dynamics keyboards are compatible with

AD-UTC protocol: ADCC0200 and ADCC0300.

The commands provided in this document assume

that one of these keyboards is being used. Contact

your Sales Representative for current information.

AD-UTC Command Summary

Table 3 lists the commands to operate the

configuration utility in AD-UTC environment. The

keyboard must be in programming mode to

perform these functions.

Table 3: Configuration Menu Commands

Command Function

(Function, and

then Shift+Menu)

Start the configuration utility.

Joystick

(Pan/Tilt) Move the highlight bar on the

active menu.

(Focus Far)

(Focus Near)

Select the highlighted item on

the active menu.

(Zoom In) or

Twist joystick

clockwise

Increase the value of the

selected setting.

Display the next choice for the

setting.

(Zoom Out)

or Twist joystick

counterclockwise

Decrease the value of the

selected setting.

Display the previous choice for

the setting.

(Function, and

then Shift+Clear)

Save changes and exit the

utility from any screen.

When setting names or entering password

information, the screen displays the available

characters in the selected language. Table 4

provides the name programming and password

entry commands:

Table 4: Name Programming/Password Entry

Commands

Command Function

Joystick

Left/Right Move the highlight left or right

in the character field.

Joystick Up/Down Move the highlight up or down

in the character field.

(Focus Far)

(Focus Near)

Select the highlighted

character in the character

field.

SPEEDDOME ULTRA VII CAMERA DOME CONFIGURATION UTILITY 8200-0184-09, REV. A

OPERATOR’S MANUAL SUPPLEMENT 6 of 13

Command Function

(Zoom In) or

Twist joystick

clockwise

Move the cursor to the right of

the current character in the

name or password.

(Zoom Out)

or Twist joystick

counterclockwise

Move the cursor to the left of

the current character in the

name.

Additional Dome Commands

Table 5 provides the special commands available

when using the dome in an AD-UTC network.

These commands are available when you enter the

keyboard combination provided.

Table 5: Additional Dome Commands

Command Function

(Function),

Preset # (1-96), and

then (Preset)

Program selected Preset

Preset # (1-96), and

then (Preset)

Recall selected Preset

(Function),

pattern # (1-3), and

then +

(Shift+Preset)

Start selected Pattern

programming

Pattern # (1-3), and

then

(Function)

Save Pattern programming

Pattern # (1-3), and

then +

(Shift and Preset)

Run selected Pattern

continuously

(Function+Focus Far)

(Function+Focus

Near)

Resume Auto Focus mode

(Function+Iris Open)

(Function+Iris Close)

Resume Auto Iris mode

(Flip) Rotate dome 180° from current

position (“flip”)

Performance Notes

Keep the following considerations in mind when

using the SpeedDome Ultra VII camera dome in

the AD-UTC environment.

Address Setting

The SpeedDome Ultra VII camera dome must be

set to address 891 to operate in the AD-UTC

environment. When the dome initializes or resets,

the address and protocol information (UTC_T)

appear on-screen.

Accessing the Quick Set Menu

The Quick Set Menu provides easy access to

specific SpeedDome Ultra VII functions from the

keyboard. To access the Quick Set menu, select

the dome, and press (Quick Set button).

See Quick Set Menu on page 2 for information

about the Quick Set functions.

SensorNet and RS-422

Matrix Switchers and

Controllers

The following provides information about

SensorNet and RS-422 controllers compatible with

SpeedDome Ultra VII. Specific operating

considerations are also included.

VM8

Supported Protocol SensorNet

Maximum Presets 0

Maximum Patterns (1) 1

Quick Set Menu Not supported

Address Range 1-8

Notes:

(1) Apple Peel only. Programmable patterns are

not available.

SPEEDDOME ULTRA VII CAMERA DOME CONFIGURATION UTILITY 8200-0184-09, REV. A

OPERATOR’S MANUAL SUPPLEMENT 7 of 13

VM16/ADTT16 (White Touch

Tracker)

Supported Protocol SensorNet

RS-422 (1)

Maximum Presets 96 – SensorNet

4 – RS-422

Maximum Patterns (2) 3

Quick Set Menu Not supported

Address Range 1-16

Notes:

(1) Requires RCSN422 code converter.

(2) Patterns are limited by time and the number of

available dome commands. Total time for each

pattern cannot exceed 6 minutes 50 seconds.

Total dome commands used in all patterns

cannot exceed 99.

VM16E/ADTT16E (Black Touch

Tracker)

Supported Protocol SensorNet

RS-422 (1)

Maximum Presets 96 – SensorNet

4 – RS-422

Maximum Patterns (2) 3

Quick Set Menu Yes (3)

Address Range 1-16 or

1-64 (3)

Notes:

(1) Requires RCSN422 code converter.

(2) Patterns are limited by time and the number of

available dome commands. Total time for each

pattern cannot exceed 6 minutes 50 seconds.

Total dome commands used in all patterns

cannot exceed 99.

(3) Requires firmware version 0701-2833-0103

(EEPROM) / 0701-2834-0201 (Flash PROM)

or newer.

VM32/AD32

Supported Protocol SensorNet

RS-422 (1)

Maximum Presets 96 – SensorNet

4 – RS-422

Maximum Patterns (2) 3

Quick Set Menu Not supported

Address Range 1-32

Notes:

(1) Requires RCSN422 code converter.

(2) Patterns are limited by time and the number of

available dome commands. Total time for each

pattern cannot exceed 6 minutes 50 seconds.

Total dome commands used in all patterns

cannot exceed 99.

VM96 (1)

Supported Protocol SensorNet

RS-422

Maximum Presets Unlimited (2)

Maximum Patterns (3) 3

Quick Set Menu Not supported

Address Range 1-32

Notes:

(1) Requires software version 5.2 or newer.

(2) Preset information is stored at the host, not the

dome.

(3) Patterns are limited by time and the number of

available dome commands. Total time for each

pattern cannot exceed 6 minutes 50 seconds.

Total dome commands used in all patterns

cannot exceed 99.

SPEEDDOME ULTRA VII CAMERA DOME CONFIGURATION UTILITY 8200-0184-09, REV. A

OPERATOR’S MANUAL SUPPLEMENT 8 of 13

AD2150/AD2350

Supported Protocol RS-422 (1)

Maximum Presets 16 (2) or 60 (3)

Maximum Patterns (4) 3

Quick Set Menu Not supported

Address Range 1-32

Notes:

(1) Requires the AD2083-02 series code converter.

(2) Preset information is stored at the converter, not the

dome.

(3) Requires AD2083-02 with firmware version 0701-

11YB-156A or newer. Preset information is stored in

the dome, not the converter.

(4) Patterns are limited by time and the number of

available dome commands. Total time for each

pattern cannot exceed 6 minutes 50 seconds. Total

dome commands used in all patterns cannot exceed

99.

AD1650

Supported Protocol RS-422 (1)

Maximum Presets 16 (2) or 60 (3)

Maximum Patterns (4) 3

Quick Set Menu Not supported

Address Range 1-128 (5)

Notes:

(1) Requires the AD2083-02 series code converter.

(2) Preset information is stored at the converter, not the

dome.

(3) Requires AD2083-02 with firmware version 0701-

11YB-156A or newer. Preset information is stored in

the dome, not the converter.

(4) Patterns are limited by time and the number of

available dome commands. Total time for each

pattern cannot exceed 6 minutes 50 seconds. Total

dome commands used in all patterns cannot exceed

99.

(5) Requires additional equipment to achieve these

numbers. A dome address within each group of 64

or 99 cameras is reserved as a global broadcast

address.

AD168

Supported Protocol SensorNet (1)

RS-422 (1) or (2)

Maximum Presets 16 (1)(2), 64 (1)(3), or

60 (4)

Maximum Patterns (5) 3

Quick Set Menu Not supported

Address Range SensorNet: 1-180

RS-422: 1-99 (1)(6) or

1-180 (2)(6)

Notes:

(1) Requires the appropriate code control module.

(2) Requires the AD2083-02 series code converter.

(3) Presets information is stored at the converter or

control module, not the dome.

(4) Requires AD2083-02 with firmware version 0701-

11YB-156A or newer. Preset information is stored in

the dome, not the converter.

(5) Patterns are limited by time and the number of

available dome commands. Total time for each

pattern cannot exceed 6 minutes 50 seconds. Total

dome commands used in all patterns cannot exceed

99.

(6) Requires additional equipment to achieve these

numbers. A dome address within each group of 64

or 99 cameras is reserved as a global broadcast

address.

AD2050

Supported Protocol RS-422 (1)

Maximum Presets 16 (2) or 60 (3)

Maximum Patterns (4) 3

Quick Set Menu Not supported

Address Range 1-1024 (5)

Notes:

(1) Requires the AD2083-02 series code converter.

(2) Preset information is stored at the converter, not the

dome.

(3) Requires AD2083-02 with firmware version 0701-

11YB-156A or newer. Preset information is stored in

the dome, not the converter.

(4) Patterns are limited by time and the number of

available dome commands. Total time for each

pattern cannot exceed 6 minutes 50 seconds. Total

dome commands used in all patterns cannot exceed

99.

(5) Requires additional equipment to achieve these

numbers. A dome address within each group of 64

or 99 cameras is reserved as a global broadcast

address.

SPEEDDOME ULTRA VII CAMERA DOME CONFIGURATION UTILITY 8200-0184-09, REV. A

OPERATOR’S MANUAL SUPPLEMENT 9 of 13

MegaPower LT

Supported Protocol SensorNet

Maximum Presets 96

Maximum Patterns (1) 3

Quick Set Menu Yes (2)

Address Range 1-32

Notes:

(1) Patterns are limited by time and the number of

available dome commands. Total time for each

pattern cannot exceed 6 minutes 50 seconds. Total

dome commands used in all patterns cannot exceed

99.

(2) Requires a compatible keyboard.

MegaPower 48

Supported Protocol SensorNet

RS-422

Maximum Presets 96(1)

Maximum Patterns (2) 3

Quick Set Menu Yes (3)

Address Range 1-48

Notes:

(1) Preset information is stored at the host, not the

dome.

(2) Patterns are limited by time and the number of

available dome commands. Total time for each

pattern cannot exceed 6 minutes 50 seconds. Total

dome commands used in all patterns cannot exceed

99.

(3) Requires firmware 1.07 or newer and a compatible

keyboard.

MegaPower 1024

Supported Protocol RS-422 (1)

Maximum Presets 16 (2) or 60 (3)

Maximum Patterns (4) 3

Quick Set Menu Not supported

Address Range 1-1024 (5)

Notes:

(1) Requires the AD2083-02 series code converter.

(2) Preset information is stored at the converter, not the

dome.

(3) Requires AD2083-02 with firmware version 0701-

11YB-156A or newer. Preset information is stored in

the dome, not the converter.

(4) Patterns are limited by time and the number of

available dome commands. Total time for each

pattern cannot exceed 6 minutes 50 seconds. Total

dome commands used in all patterns cannot exceed

99.

(5) Requires additional equipment to achieve these

numbers. A dome address within each group of 64

or 99 cameras is reserved as a global broadcast

address.

Panasonic UTC Protocol

Preset Programming

The Dome Configuration Menu must be used to

program Presets. Up to 64 Presets may be

programmed using the Panasonic UTC protocol.

These instruction apply to the following equipment:

• Panasonic WJ-SX550 Multiplexer

• Panasonic WV-CU550A Controller

1. Select the monitor and camera number

assigned to the Speed Dome Ultra VII camera

dome.

2. Use the arrow keys on the controller to scroll to

the Camera Setup Menu (D4).

3. Press F1 (On) key to display the Dome

Configuration Menu.

4. Use the joystick to move the highlight to

Alarms/Areas/Home/Presets/PZ. Press Set

to select.

ALARMS/AREAS/HOME/PRESETS/PZ

SET ALARM ACTIONS

SET ALARM STATES

SET HOME POSITION

SET NORTH POSITION

AREA BOUNDARIES

PRIVACY ZONES

PRESETS

SCAN LIMITS

EXIT

SPEEDDOME ULTRA VII CAMERA DOME CONFIGURATION UTILITY 8200-0184-09, REV. A

OPERATOR’S MANUAL SUPPLEMENT 10 of 13

5. Use the joystick to move the highlight to

Presets. Press Set to select. The Select

Preset to Program screen displays.

SELECT PRESET TO PROGRAM

PRESET

NUMBER PRESET NAME

1-96 PRESET 1-96

FOCUS FAR to program preset

EXIT

6. Use the joystick to select the Preset you want

to program. If the Preset has been

programmed the dome automatically moves to

that position.

 Move the joystick right to increase the

preset number.

 Move the joystick left to decrease the

preset number.

When the correct Preset number appears,

press Set to begin programming.

7. The Presets screen displays. Use the joystick

to adjust the dome to the correct pan/tilt

position.

PRESETS

PRESET X

Position camera with PAN

TILT, ZOOM and IRIS

FOCUS FAR to save and exit

EXIT

IMPORTANT! If using the WV-CU550A

Controller with the WJ-SX550 Multiplexer, you

must press F3 (A. Res) to adjust the zoom,

focus, or iris settings. This places the controller

in normal navigating mode. Make the

necessary adjustments. When finished, press

F1 (On) to resume menu mode.

8. Press Set to save the Preset information.

9. To program more Presets, repeat steps 5

through 8. To exit the Dome Configuration

Menu and save changes, press F4 (Exit).

To verify the Preset programming, enter a Preset

number (1-64) and press Preset.

Specifications-Indoor Dome

Operational

Pan/Tilt:

Manual Pan Speed......................... 0.2°-100° per second

(scaled to zoom position)

Manual Tilt Speed........................ 0.25°-100° per second

(scaled to zoom position)

Preset Pan/Tilt Speed............220° per second maximum

Pan Travel..................................360° continuous rotation

Tilt Travel ..................................................................>90°

Pan/Tilt Accuracy.....................................................±0.5°

22X Camera Zoom Functions:

Optical Zoom..............................................................22X

Digital Zoom...............................................................11X

Zoom Pause......................................... 22X selectable or

33X default

Total Zoom...............................................................242X

Maximum Zoom Stop.......44X, 66X, 88X (default), 110X,

132X, 154X, 176X, 198X, 220X, 242X

Zoom/Focus Accuracy ...........................................±0.5%

23x Day/Night Camera Zoom Functions:

Optical Zoom..............................................................23X

Digital Zoom...............................................................10X

Zoom Pause......................................... 23X selectable or

35X default

Total Zoom...............................................................230X

Maximum Zoom Stop.......46X, 69X, 92X (default), 115X,

138X, 161X, 184X, 207X, 230X

Zoom/Focus Accuracy ...........................................±0.5%

Auto Synchronization:

Line Locked.........................Remote V-phase adjustment

Internal..........................................Built-in sync generator

Address Range .......................................................1-255

Number of Presets:

VM16 / ADTT16 ...........................96 with SensorNet 485

VM32 / AD32................................96 with SensorNet 485

AD2150.............................................64 with Manchester

16 with RS422 (using AD2083-02A)

VM96......................Virtual with RS422 or SensorNet 485

VM168 / AD168................................64 with Manchester,

RS-422 or SensorNet

16 with RS422 (using AD2083-02A)

AD2050.............................................64 with Manchester

16 with RS422 (using AD2083-02A)

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels American Dynamics Logiciel

American Dynamics

American Dynamics SpeedDome Ultra VII Instructions d'installation et d'utilisation

American Dynamics

American Dynamics Excalibur 168 Manuel utilisateur

American Dynamics

American Dynamics Version 4.3 Software Update 3 Comment utiliser

American Dynamics

American Dynamics Browser Client Manuel utilisateur

American Dynamics

American Dynamics Video Management Systems Manuel utilisateur

American Dynamics

American Dynamics Excalibur AD5500 Manuel utilisateur

American Dynamics

American Dynamics Intellex Policy Manager Manuel de l'opérateur

American Dynamics

American Dynamics SpeedDome Ultra VII EIS Manuel utilisateur

American Dynamics

American Dynamics Intellex Digital Recorder Manuel utilisateur

American Dynamics

American Dynamics SpeedDome Ultra VII Manuel utilisateur

American Dynamics

American Dynamics SpeedDome Ultra II Manuel utilisateur

American Dynamics

American Dynamics SpeedDome Ultra III Manuel utilisateur

American Dynamics

American Dynamics MegaPower 3200 Manuel utilisateur

American Dynamics

American Dynamics Excalibur AD5500 Manuel

American Dynamics

American Dynamics Intellex Digital Recorder Manuel de l'opérateur

American Dynamics

American Dynamics MegaPower 3200 Release 2.0 Comment utiliser

American Dynamics

American Dynamics MegaPower 48 Plus Manuel utilisateur

American Dynamics

American Dynamics Intellex Intellex LT Guide de démarrage rapide

American Dynamics

American Dynamics EDVR Calculator Manuel utilisateur

American Dynamics

American Dynamics Excalibur 168 Manuel utilisateur

American Dynamics

American Dynamics Intellex Policy Manager Manuel utilisateur

American Dynamics

American Dynamics Excalibur 168 Manuel

American Dynamics

American Dynamics CPU Activity Log Client Mode d'emploi

American Dynamics

American Dynamics RAS915LS Manuel utilisateur

Manuels Logiciel populaires d'autres marques

COMPRO

COMPRO COMPROFM Manuel utilisateur

Muratec

Muratec OFFICEBRIDGE ONLINE Manuel utilisateur

Oracle

Oracle Contact Center Anywhere 8.1 Manuel utilisateur

Adobe

Adobe 65007312 - Photoshop Lightroom Manuel

Avaya

Avaya NULL One-X for RIM Blackberry Manuel utilisateur

HP ProLiant BL420c Manuel utilisateur

PS Audio

PS Audio PowerPlay Manuel du propriétaire

Brady

Brady LOCKOUT PRO 3.0 Manuel de service

Avaya

Avaya Interaction Center Manuel utilisateur

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Manuel

Novell

Novell GROUPWISE 8 - INTERNET AGENT Manuel utilisateur

Oracle

Oracle Application 9i Manuel utilisateur

Acer

Acer RDM Manuel utilisateur

Canon

Canon Vixia HF21 Manuel utilisateur

Canon

Canon ZR950 Manuel utilisateur

Samsung

Samsung Auto Backup Manuel utilisateur

Polycom

Polycom Vortex EF2201 Instructions d'installation et d'utilisation

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Manuel utilisateur