Amegia Network Camera Manuel utilisateur

2 Megapixels

High-End Box

Network Camera

User’s Manual

Version 1.7

Table o Contents

1 OVERVIEW ........................................................................................................................................................................ - 4 -

2PRODUCT DESCRIPTION................................................................................................................................................... - 4 -

2.1 Hardware Description..........................................................................................................................................- 5 -

3SETTING UP THE NETWORK CAMERA..............................................................................................................................- 6 -

3.1 R

EAD

EFORE

.........................................................................................................................................................-

3.2 H

ARDWARE

STALLATIO

TEPS

.....................................................................................................................................-

3.3 U

SI G THE

ETWORK

AMERA FOR THE FIRST TIME

.............................................................................................................-

3.4 U

SI G THE

ERMI AL

LOCK

...........................................................................................................................................-

3.5 P

OWER

OVER

-E

THER ET SUPPORTED

ETWORK

AMERAS

.................................................................................................-

3.6 U

SI G THE

ICRO

ARD

.........................................................................................................................................-

4ACCESSING THE NETWORK CAMERA.............................................................................................................................- 12 -

4.1 F

I DI G THE CAMERA

..................................................................................................................................................-

4.2 B

EFORE

SSIG I G A

DDRESS

................................................................................................................................-

4.3 A

SSIG I G THE

ADDRESS TO THE ETWORK CAMERA

......................................................................................................-

4.4 A

CCESS THE CAMERA FROM THE BROWSER

.......................................................................................................................-

4.5 T

IVE

IEW

AGE

...................................................................................................................................................-

4.6

HO E

AMERA

IEWER

.............................................................................................................................................-

5CONFIGURING THE CAMERA.......................................................................................................................................... - 20 -

5.1 V

IDEO

ETTI GS

.........................................................................................................................................................-

5.2 C

AMERA

ETTI GS

......................................................................................................................................................-

5.3 S

TORAGE

ETTI GS

.....................................................................................................................................................-

5.4 E

VE T

ETTI GS

.........................................................................................................................................................-

5.5

ETWORK

ETTI GS

....................................................................................................................................................-

5.6 S

YSTEM

ETTI GS

.......................................................................................................................................................-

5.7 A

PPLICATIO

..............................................................................................................................................................-

6TROUBLESHOOTING.......................................................................................................................................................- 54 -

6.1 F

ACTORY

EFAULT

......................................................................................................................................................-

6.2 V

IEWI G THE CAMERA FROM A REMOTE LOCATIO

............................................................................................................-

7FREQUENTLY ASKED QUESTIONS...................................................................................................................................- 58 -

8TECHNICAL SPECIFICATIONS .......................................................................................................................................... - 60 -

9GLOSSARY OF TERMS ..................................................................................................................................................... - 62 -

10 FCC STATEMENT ............................................................................................................................................................. - 69 -

Disclaimer

The textual contents and images in this documentation are written based on the currently distributed

versions of our hardware, firmware and software. However, updates or changes can occur due to

unexpected circumstances, hence, the text or images appear in your document version might not be seen

as identical to the actual software or hardware you are using. To avoid misunderstanding or

misinterpretation, please refer to our official website at www.amegia.com or the FAQ document supplied

upon request/product delivery.

If you have any inquiry about our products or customization services, please contact us.

Tel: 886-2-8228-6161

Email: [email protected]

Address: 6F, No.199, Lide St., Jhonghe District., New Taipei City 23556, Taiwan, R.O.C

Website: http://www.amegia.com

1Overview

This camera is a high-end 2 Megapixel Box etwork Camera, which is designed for professional security applications.

This network camera is equipped with ICR (IR-Cut filter Removable) and provides outstanding day and night

performance. It comes with a 2 Megapixel CMOS Sensor, with a maximum resolution of 1600 x 1200, delivering sharp

image quality. Besides Pelco D/P protocol for PTZ (Pan/Tilt/Zoom), the Digital PTZ function allows user to navigate any

area of the monitored image with maintained sharp resolution. With unique features, this network camera provides an

ideal solution for surveillance and monitoring.

2Product Description

Key eatures

1. H.264 High Pro ile / MJPEG Dual Compression:

Offers the user the option to select H.264 or MJPEG compression.

2. Compact Size or Easy Installation and Maneuvering:

Small and light weighted, for areas that are limited in space.

3. ONVIF ® Compliant or Easy Integration & Fast Deployment:

Web services built-in with international standard protocols, integration cycles have been reduced and

deployment has become easier. ( Contact your distributor for documentation).

4. Multiple video pro iles simultaneously or streaming:

Streams up to 8 independent streams with multiple profiles.

Different configurations can be set according to the bandwidth that is available from the network.

5. In rared-Cut Filter Removable or Day & Night Environment

The etwork Camera comes with an infrared-cut filter removable (ICR) already built-in, for which turns the

video into black & white once the illumination that enters into the camera is not enough.

6. Audio In & Audio Out Connectors or Camera Audio enhancements

Offers an Audio In connector and an Audio Out connector to connect to an external microphone and

speaker, in order to transmit two way audio together with the video streaming.

7. Micro SD Card Slot or Local Storage

For saving snapshots that can be later checked by the user, upon events occurred during motion detection.

8. Analog Video BNC Out or Video Redundancy on Analog devices

The etwork Camera has a video output with analog signal that allows connecting to analog monitors.

9. Alarm In & Alarm Out or connecting Alarm Devices

The etwork Camera comes with a Terminal Block for connecting alarms to execute actions upon it.

10. RS485 Connector or PTZ Support

Placing the etwork Camera into a Pan Tilt device, control the Pan& Tilt device smoothly.

11. Power-over-Ethernet IEEE 802.3 a or simpli ied connection ( Optional)

Make installations simple with connecting only one cable without additional powering sources.

2.1 Hardware Description

Video Out B C Connector (75 Ohm) for connecting analog monitor

Power Jack connect AC/DC power adapter for DC12V power input

Ethernet RJ45 port for network connection

Micro SD insert SD card for local storage

DC Iris connect to control the iris of lens that supports DC iris

Level adjust the iris level

Reset use a pin to insert into it to ignite the reset function

*The Bracket Pad comes as an accessory of the box camera. Place the stand mounting pad on the top/bottom

panel of the camera for different mounting options. Secure the pad with the two supplied retention screws and

tighten them up with the supplied L-wrench or another screwdriver in proper size.

Terminal Block De inition

COM Common 485B RS485(-)

D_OUT Relay ormal Open / Close GND Ground

D_IN Digital Input A_IN Audio In

485A RS485(+) A_OUT Audio Out

Reset

3Setting up the Network Camera

3.1 Read Be ore Use

The use of surveillance devices may be prohibited by law in your country. The etwork Camera is not only a

high-performance web-ready camera but can also be part of a flexible surveillance system. It is the user’s

responsibility to ensure that the operation of such devices is legal before installing this unit for its intended use.

It is important to first verify that all contents received are complete. Take note of the warnings in the Quick

Installation Guide before the etwork Camera is installed; then carefully read and follow the instructions in the

Installation chapter to avoid damage due to faulty assembly and installation. This also ensures the product is used

properly as intended. It is designed for various applications including video sharing, general security/surveillance,

etc.

3.2 Hardware Installation Steps

After unpacking the package and identifying its parts, assemble the network camera to run the device for the first

time.

It is recommended set up the camera before installing it to the intended location.

The following instructions will consist of basic steps that will help you through the hardware preparation.

Other required devices before powering up the etwork Camera:

1. Personal Computer or Laptop; and

2. etwork Hub or Switch and 2 (two) pieces of Ethernet Cable; or

3. 1(one) piece of Crossover Ethernet Cable

Using a CS Type Mount Lens

Use a CS Type Mount Lens for the etwork Camera. It is recommended using megapixel lenses, supporting a pixel

size of 2.8μm x 2.8μm, 1/3” inch size.

There are two mini screw holes around CS mounting ring. Use the two provided CS lens mounting screws to mount

a CS lens.

Installing the Network Camera

A. Attach the bracket that comes in the package to the Bracket ut Hole

B. Connect the Ethernet Plug to the etwork Connector RJ-45 from the device.

C. Plug the Power Jack to the Power Connector ( ot necessary for Power-over-Ethernet etwork

Camera Models).

After the Power Connector is plugged in, the etwork Camera will boot up. Wait a few seconds for the etwork

Camera to startup

How to adjust the lens ocus

In order to adjust the focus of the etwork Camera, turn the focus ring in clockwise direction to get the

appropriate image.

Note: it is required get connected to the etwork Camera prior to adjust the focus.

3.3 Using the Network Camera or the irst time

The etwork Camera is a network device and its use should be straightforward for those who have basic

networking knowledge. Making the initial steps for setting up the network camera will be based on a simple

network connection.

Option 1

Connect the network camera to a HUB / Switch which is connected to a PC

Option 2

Connect the network camera directly to a PC with a crossover cable.

After the network camera has its activity lights on, use the PC for setting up the IP Address of the etwork camera.

Refer to the section of “Accessing the Network Camera” at the next page for detailed instructions.

Hints: Possible Network Con igurations in your network in rastructure

1. Con iguration 1

Internet Access: ADSL or Cable Modem

IP address: One real IP or one dynamic IP

Connection Type: Only the etwork Camera connects to the internet

For fixed real IP, set up the IP into the etwork camera. For dynamic IP, start PPPoE.

2. Con iguration 2

Internet Access: ADSL or Cable Modem

IP address: More than one real IP or one dynamic IP

Connection Type: The etwork Camera and PC connect to the internet

Device needed: Switch Hub

For fixed real IP, set up the IP into the etwork camera and PC. For dynamic IP, start

PPPoE.

3. Con iguration 3

Internet Access: ADSL or Cable Modem

IP address: one real IP or one dynamic IP

Connection Type: The etwork Camera and PC connect to the internet

Device needed: IP sharing such as Hub / Switch and a Router

Use virtual IP, set up port forwarding in IP sharing.

(Suggestion: Refer to your etwork Administrator if necessary for more information)

3.4 Using the Terminal Block

The network camera comes with a Terminal Block

that can offer multiple functions to the user:

Pin 1 ~ 3, 6: Intended for triggering and receiving

alarms for the Event Configuration feature.

Pin 4~ 5: for connecting Pan Tilt and Zoom devices.

The network camera can be placed with Pan / Tilt

device to control the pan left/right, or tilt up/down. It

may also be possible to use motorized zoom cameras,

in order to zoom in/out at convenience.

Pin 7 ~ 8: For connecting audio devices, that allows

the transmission of audio through the video

streaming.

3.4.1 Connecting Alarm devices

Connect Pin 1 and Pin 2 for an external relay device such as an alarm that expects to be activated.

Connect Pin 3 and Pin 6 for an external Triggering device for sending a signal into the etwork Camera.

Refer to Chapter 5) Configuring the camera, Event Settings for more references on how to use the even

trigger and alarm to perform tasks such as taking snapshots and uploading images.

3.4.2 Connecting Audio Devices

The etwork Camera has an Audio Input (Line in) and Audio Output (for connecting speakers) with

Mono quality. The connection of audio may also share the Ground Point of Pin 6.

Refer to Chapter 5) Configuring the Camera, Camera Settings for more references on enabling the

audio device.

COM Relay Common

D_OUT

Relay ormal Open / Close

D_I Digital Input

485B RS485(-)

485A RS485(+)

G D Ground

A_I Audio In

A_OUT

Audio Out

Terminal Bloc

k Definition

Pin 1

Pin 2

Pin 3

Pin 6

3.4.3 Connecting Pan/Tilt/Zoom Devices

The etwork Camera allows the connection of a Pan/Tilt/Zoom device into the camera.

The RS485 (+) and RS485(-) may be used for connecting such devices.

The supported protocol is Pelco D and Pelco P.

Refer to Chapter 5) Configuring the Camera, Camera Settings for more references on setting and

controlling the device by the Web user interface.

3.5 Power-over-Ethernet supported Network Cameras

The etwork Camera comes as an optional model which supports Power-over-Ethernet (PoE).

Using Power-over-Ethernet as power supplying mode, takes advantage of having a simple connection, with

only one Ethernet Cable to act like Data and Power transmission. And it is not necessary to use any Power

Adapter since the powering will be done directly through the Ethernet Connector.

Below a comparison between a Regular Ethernet connection and a connection using etwork Camera with

built-in Power-over-Ethernet.

Power Adapter

ADSL Modem

Network Camera with

Power-over-Ethernet

Broadband Router

POE

Switch

Ethernet cab e Ethernet cab e Ethernet cab e

POE Switch & POE Network Camera

Power Adapter

ADSL Modem

Network Camera

Broadband Router

Hub / Switch

Ethernet cab e Ethernet cab e Ethernet cab e

Non-POE Connection

Note: For safety precautions, when using a PoE Video Encoder, ensure that the standard Power

Connector has been Deleted before plugging the Ethernet cable (which is attached on the other end to a

PoE Hub / Switch).

Table des matières

Autres manuels Amegia Caméra de sécurité

Amegia

Amegia AM1200 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur