Ambit T60H656 Manuel utilisateur

U S E R ’ S M A N U A L

T60H656

Mini-PCI Type IIIB WLAN CARD

Ambit Microsystems Corporation

5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.

TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: Ambit@shts.seed.net.tw

Contents

SECTION ONE: INTRODUCTION.............................................................................................1

1.1 FEATURES...............................................................................................................................1

1.1.1 WIRELESS LAN FUNCTION.....................................................................................................1

1.2:FCC NOTICE...................................................................................................................................2

1.2.1 FCC COMPLIANCE .........................................................................................................................

1.2.2 FCC CLASS B STATEMENT .........................................................................................................2

SECTION TWO: WIRELESS LAN INSTALLATION...............................................................4

2-1 SYSTEM REQUIREMENTS ................................................................................................................4

2-2 INSTALLATION AND UNINSTALL PROCESS.......................................................................................4

SECTION THREE: WIRELESS UTILITY AND CONFIGURATION.....................................6

3-1 WINDOWS 98/ME/2000 WIRELESS UTILITY ...................................................................................6

SECTION FOUR: WINDOWS XP WIRELESS UTILITY AND CONFIGURATION.............6

4-1 WINDOWS XP WIRELESS UTILITY ..................................................................................................6

APPENDIX A GLOSSARY..................................................................................................................6

The information contained in this manual has been verified at the time of this manual printing. The

manufacturer reserves the right to make any changes and improvements in the product described in this

manual at any time and without notice.

All registered trademarks are the property of their respective owners.

Section One: Introduction

Ambit Wireless Mini-PCI Module complied with IEEE 802.11b 11Mbps Standard, it

can be used to provide a variety of low-cost wireless network interface card to connect

your wireless LAN via fitting into the MiniPCI Type III slot. The Wireless MiniPCI

Module that complies with this specification and combines networking with high-

speed Internet access will let people connect to the Internet anywhere, anytime.

With seamless roaming, fully interoperability and advanced security with WEP

standard, Wireless MiniPCI Module can allow user to switch to different vendors’

Access Points through the wireless networks and to prevent from eavesdropping.

1.1 Features

1.1.1 Wireless LAN Function

Form Factor & Bus Interface MiniPCI Type IIIB, compliant to MiniPCI

Specification Rev 1.0

Wireless LAN Compliance IEEE 802.11b

Radio Technology Direct Sequence Spread Spectrum

Operating Frequency 2.4 ~ 2.497GHz ISM band

Modulation Schemes DQPSK, DBPSK and CCK

Channel Numbers IEEE 802.11b compliant

1 ~ 11 channels for United States

1 ~ 13 channels for Europe

1 ~ 13 or 14 channels for Japan

WLAN Data Rate 11, 5.5, 2, and 1Mbps

Spreading 11-chip Barker Sequence

Media Access Protocol CSMA/CA with ACK

Transmitter Output Power Typ. 13+/-1 dBm

Receiver Sensitivity Typ. –82 dBm for 11Mbps @ 8% PER

Typ. –85 dBm for 1Mbps @ 8% PER

Antenna Type Integrated diversity switch with Hirose

compliant connectors(U-FL) for connecting

dual diversity antennas

Operating Voltage 3.3VDC

Radio On / Off

Dynamic Rate Shifting Automatic fallback

Network Architecture Ad-hoc, Infrastructure

Operating Systems Windows 98/Me/2000/XP

Mechanical Requirements Mini-PCI Type IIIB dimension.

1.2:FCC Notice

1.2.1 FCC Class B Statement

This equipment has been tasted and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy, and if not installed and used in accordance with the instructions, may cause

harmful interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and

on , the user is encouraged to try to correct the interferencr by one or more of the following measures:

!Reorient or relocate the receiving antenna

!increase the separation between the equipment and the receiver

!Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected

!Consult the dealer or an experienced radio/TV technician for help

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

This device is intended only for OEM integrators under the following conditions:

1) The transmitter module may not be co-located with any other transmitter or antenna.

As long as the 2 conditions above are met, further transmitter testing will not be required. However,

the OEM integrator is still responsible for testing their end-product for any additional compliance

requirements required with this module installed (for example, digital device emissions, PC peripheral

requirements, etc.).

The OEM integrator is required to label their end product using this module by the warning statement

such as “This product integrate an RF module with FCC ID: MCLT60H65600”.

The OEM integrator is not allowed to use the antenna which is not included in this authorization. Also

the warning statement of the use of the antenna which is not approved in this authorization should be

also included in the users manual of the end product.

IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop

configurations or co-location with another transmitter), then the FCC authorization is no longer

considered valid and the FCC ID can not be used on the final product. In these circumstances, the

OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and

Obtaining a separate FCC authorization.

Section Two: Wireless Lan Installation

2-1 System Requirements

In order to install Wireless LAN driver and Utility and use the Wireless LAN card in your notebook computer.

Your notebook system must meet the following requirements:

!Ambit Mini-PCI Wireless LAN Card already inserted

!Windows 98SE,2K,ME,XP OS Support

2-2 Installation and Uninstall Process

Install Wireless LAN (Windows 98/2K/ME/XP)

1. While power on and open Windows OS at first time, the OS will detect Wireless LAN

Card exist and pop up the following dialogue. If you don’t want to perform install process

now, then press ‘Cancel’ bottom. If you want to install now, please wait a moment then

you can see the next InstallShield Wizard dialogue pop up.

If you press ‘Cancel’ Bottom at the above dialogue, but you want to start install process later.

Execute the program ‘Setup.exe’ in the CD. Windows displays the dialog as below. Press

‘Next’ button to continue.

2. It displays a License Agreement dialog. Press ‘Next’ to continue.

3. Select the destination folder that you want to place the files.

4. Wait for the install program to do the installation.

5. Congratulations! Wireless LAN has been installed successfully.

Please click ‘Finish’ to go to the next step.

6. Please remove any disks from any drives before your click ‘Finish’.

Then click ‘Finish’to complete setup.

Uninstall Wireless LAN (Windows 98/2K/ME/XP)

1. One can remove the Wireless LAN via the ‘Add/Remove Programs’ in the

‘Control Panel’. Select ‘Wireless LAN’ and click ‘Add/Remove’ button, the

dialog as below displays.

2. Select ‘Remove’ and then click the ‘Next’ button to perform the un-installation.

Click ‘OK’ button if you really want to remove the Wireless LAN.

3. Wait for the un-installation to do its work.

4. Click ‘Finish’ to complete the un-Installation.

Table des matières

Autres manuels Ambit Carte réseau

Ambit

Ambit T60H813 Manuel utilisateur

Ambit

Ambit PCMCIA Manuel utilisateur

Ambit

Ambit T60H677 Manuel utilisateur

Ambit

Ambit T60L198.00 Manuel utilisateur

Manuels Carte réseau populaires d'autres marques

FirstComm

FirstComm OBiWiFi5G Manuel utilisateur

Sun Microsystems

Sun Microsystems Interface Adapter Manuel utilisateur

TRENDnet

TRENDnet TU2-ETG Manuel utilisateur

YASKAWA

YASKAWA SI-EN3 Manuel utilisateur

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manuel utilisateur

Belkin

Belkin F5D7050 Manuel utilisateur

3Com

3Com EtherLink 3C509B Manuel utilisateur

TRENDnet

TRENDnet TEG-PCITX Manuel utilisateur

Cisco

Cisco MC16E Manuel utilisateur

Delta Electronics

Delta Electronics Braking Modules VFDB Series Manuel utilisateur

TwinMOS

TwinMOS Booming Manuel utilisateur

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Manuel utilisateur

Buffalo

Buffalo AirStation WLI-PCM-L11GP Manuel utilisateur

National Instruments

National Instruments NI 9234 Manuel utilisateur

Hama

Hama 49276 Manuel utilisateur

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Manuel d'utilisation

Compaq

Compaq Wireless LAN 100 Manuel utilisateur

Bose

Bose PowerMatch Dante Manuel utilisateur