Ambient TOUCH LIGHT Mode d'emploi

50D0093 Rev 3 May 2005 Page 1 of 11 Ambient Technologies

ADivision Of

TLT

TOUCH LIGHT™ Thermostatic On/Off Remote Control

INSTALLATION AND OPERATING INSTRUCTIONS

This wireless thermostatic on/off/ remote control – system provides a safe, reliable, and user-friendly remote control

for millivolt valve gas appliances. The system can be thermostatically or manually turned on and off with the

transmitter. Always check the appliance home owner’s manual for additional information, or warnings regarding

accessory installation before connecting this remote control system.

Carefully inspect the contents for shipping damage. If any parts are missing or damaged, immediately contact the

dealer from whom you purchased the kit. Do not attempt to install any part of the kit unless all parts are in good

condition. Please keep this booklet for future reference.

CONTENTS OF KIT

Description Qty

Touch Light Transmitter 1

Battery Alkaline AA (for Transmitter and receiver) 6

Receiver (Assembly) consists of : 1

Receiver Box

Slide Button-Black (On/RS/Off)

L-Bracket (Floor Mount)

Wall Cover Plate-Black 1

Wall Cover Plate-White 1

Slide Button-White (On/RS/Off) 1

Screws (for Wall Cover Plate) 2

Plug-In Wiring Assembly – 18” Inches 1

Velcro (Loop and Hook) 1

Wall Anchor Screws 2

Wall Anchor 2

Installation Instructions

Screws (for fireplace system control covers)

Wall Bracket

FEATURES/SPECIFICATIONS

•Contemporary Ergonomic Table Top or Wall Mount Transmitter with Large LCD Display

•Easy Access Thermostatic Control

•Battery Powered Transmitter and Receiver

•Easy Access Battery Door

•Pre-Programmed for Quick Installation

•Low battery Indication

•Child Proof Lock-out

•16 Security Codes

•2 hour Shut Down (Optional)

•Thermal Safety Shutdown (Transmitter Only)

•Quick Disconnect Wiring Assembly

•Reset Button

WARNING

50D0093 Rev 3 May 2005 Page 2 of 11 Ambient Technologies

ADivision Of

Important Safety Information

•Read this manual thoroughly prior to installing, programming or operating any remote control.

•This remote control system is designed for use with a millivolt gas valve system. Do not use this remote

control system on applications with voltages above 24 Volts DC and 1 amp current.

•This remote control system requires two (2) “AA” alkaline batteries for the transmitter and four (4) “AA”

alkaline batteries for the receiver.

•Wiring must conform to appliance requirement and building codes/ordinances as required by local and

national code authorities having jurisdiction.

•Do not short (or jumper) across the gas valve terminals to test the remote control installation. This could

damage the unit and void the warranty.

•This remote control system should only be used as described in this manual. Any other use is not

recommended and will void the warranty.

NOTE

Due to the sensitive temperature monitoring components in the transmitter, it is necessary to

allow the transmitter to stabilize to room temperature before accurate room temperatures are

displayed. If the transmitter is activated from a severe cold condition, allow 15 minutes for

accurate temperature readings to appear on the LCD.

WARNING

Turn appliance OFF and allow to cool before installing or servicing. DO NOT connect

110-120 VAC wiring to the milli-volt gas control valve. The remote operator must be installed

exactly as outlined in these instructions. Read all instructions completely before attempting

installation. Follow instructions carefully during installation. Any modification of

components will void the warranty and may cause a fire hazard.

WARNING

Turn appliance OFF (at the appliance or remote receiver) if you are away from your house for

a long period of time. Never leave anything on top of the surface on the touch light

transmitter.

INSTALLATIONS

50D0093 Rev 3 May 2005 Page 3 of 11 Ambient Technologies

ADivision Of

L-Bracket

Slide Switch

Batter

Door

Remote Receiver:

The remote receiver may be wall mounted or installed in the appliance per the

appliance homeowner’s manual. Refer to the Homeowner’s Manual for special

installation instructions. If wall mounted, the remote receiver must be installed in a

junction box with cover plate provided. Failure to follow the installation instructions

found in the appropriate Homeowner’s Manual will void the warranty and may cause

a fire hazard.

Installing Batteries:

The remote receiver uses four (4) “AA”- size batteries. To install batteries,

1. Remove the slide switch by gently pulling straight out.

2. Use your thumb and index finger to gently pull down the L-bracket.

3. Open the battery door by pressing the two tabs located on the door.

4. Install the batteries as indicated in the receiver cover.

5. Close the battery door until the door tab snaps in place.

6. To install the receiver into a wall junction box, install the receiver with the

screws provided .

7. If you decided to install the receiver into the appliance, reinstall the L-

bracket.

8. Gently, install the slide switch back to the receiver stem.

9. The batteries should be replaced at least once every 6 months or when the battery indicator flashes.

Connecting the Receiver to your appliance:

This system comes with an 18 inch wire assembly. Insert the white terminal to the back of the receiver. The

terminal wire block can only be installed one way. Do not force the terminal plug onto the receiver.

Connect the wiring terminal two (2) _” female spade terminals to the appliance. Refer to the appropriate

Homeowner’s Manual for proper wiring connections to the appliance. Your appliance may have other options to

connect wiring from receiver. For applications longer than 18 inches, use 18 gauge wire, 105ºC rated, with no

splices. Connect to the two (2) 1/4“ female spade wiring terminals. Wire can be no longer than 20 feet.

WARNING

Make sure that the wires do not contact the appliances any place other than at the terminals.

Exposure to temperatures higher than 105C (250ºF) may cause the receiver to malfunction or

fire hazard.

Touch Light Transmitter:

50D0093 Rev 3 May 2005 Page 4 of 11 Ambient Technologies

ADivision Of

Installing Batteries:

The Touch Light transmitter uses two (2) “AA”- size batteries. To install

batteries,

1. Press down the battery door tab and lift up and remove the

battery door.

2. Install the battery.

3. Close the battery door by snapping in place.

4. Repeat the above step for the other battery.

5. When both batteries are installed, the transmitter will

initialize for 10 seconds and then is ready for use.

6. The batteries should be replaced at least once every 6

months or when the battery icon indicator flashes.

Setting Privacy (DIP) Switch on Receiver and Transmitter:

The remote receiver and transmitter privacy (DIP) switches are preset at the factory. In the event of activation or

interference from other nearby transmissions, reset the code using the following procedure:

1. Slide the code switches on the transmitter or receiver to your choice of ON or OFF position. Switches #1

to #4 are preset to “ON” for both the transmitter and receiver.

2. The switches on the transmitter and receiver must match in order for the system to work.

3. To check, touch the transmitter groove surfaces for at least 1 second and, the transmitter will emit a beep,

and the receiver indicator light will blink. If not repeat step 2.

4. The system is now ready to operate.

WARNING

Do not use two (2) or more remote control systems in the same area with the same dip switch

settings, as they will communicate with each other. This may cause the appliances to

malfunction.

Optional Auto Shutdown:

50D0093 Rev 3 May 2005 Page 5 of 11 Ambient Technologies

ADivision Of

1. The Touch Light transmitter comes preset from the factory with a 2 hour shutdown from its last ON

operation. This is done to prevent the appliance from continuing to run if unattended.

2. You may disable this feature if you wish. To disable, change the Touch Light transmitter privacy (DIP)

switch #1 ONLY to the OFF position (by sliding the switch towards the battery door.) Make sure the

receiver privacy (DIP) switches are set the same. Follow the instructions on how to set the privacy (DIP)

switch setting.

3. By disabling this feature, your appliance may continue to run unattended.

Reset Button:

1. The reset button can be used to reset the transmitter if transmitter is not working properly. The reset

button is located behind the battery door cover. Using a paper clip, press the reset button and the transmitter

will reset and initialize for 10 seconds before it can be used.

Where to place Touch Light Transmitter?

1. The Touch Light transmitter is recommended to be placed on a

non metal table top or wall mount. Make sure there is no direct

contact of metal parts to the body of the transmitter.

2. If wall mount, choose a mouting location about 5 feet above the

floor in an area with good air circulation and away from the

following:

a. Air ducts

b. Radiant heat from the sun and appliances

c. Concealed pipes and chimneys

3. Align the wall bracket to the desired location. Mark two (2) holes

using the wall bracket as template.

4. Drill two (2) holes and insert the plastic anchors until they are flush

with the wall.

5. Fasten securely the wall bracket to the wall with the two (2) screws.

6. Refer to the figure on how to install the transmitter to the wall bracket.

OPERATIONS:

50D0093 Rev 3 May 2005 Page 6 of 11 Ambient Technologies

ADivision Of

Transmitter:

General:

The TLT has two operating modes. It can used as manual or thermostatic On/Off remote control system.

The transmitter will operate the remote receiver from 1foot to a maximum of 20 feet. The operational range is

reduced when batteries are low or when the receiver is inside a metal enclosure.

Initial start up:

1. After initial power up or reset button is pressed, the transmitter is reset.

2. During transmitter reset, all segments of the LCD will be turned on. After ten (10) seconds, the LCD will

be initialized and operational. You will hear a beep during this time.

3. After reset, only the room temperature will be displayed on the LCD display.

Manual Mode- On or Off Operation:

1. Since Touch Light transmitter is touch sensitive equipment, we recommend to use only your index finger to

touch. Do not use any metal object to contact or touch the surface. The transmitter will recognize a valid

touch if either side of the surface area are covered more than 10% for a period of at least 1 second

2. To activate a signal, you need to touch either side of the groove surfaces for at least 1 second and then

release your finger. If the touch is valid, it will beep once and a signal will be sent to the receiver. During

this time you will see the transmission icon on the LCD display for a brief time. No other command can

be given until the transmission is completed.

50D0093 Rev 3 May 2005 Page 7 of 11 Ambient Technologies

ADivision Of

Thermostatic Mode Operation:

1. Push down on the flip door button to access the thermostatic control.

2. Press the AUTO button to enter the thermostatic mode (Beep Once). “TSTAT” and SET temp icon will

appear on the lower LCD screen

3. In thermostatic mode, press the UP πbutton or θDOWN button to set the desired set temperature.

4. Once the setting is completed, the transmitter will automatically turn on the fireplace when the room

temperature is below the set temperature and turn off the appliance when the room temperature is above

the set temperature within 1 degree.

5. There will be a slight delay in the response of the unit (on/off) to a temperature. Room temperature is

monitored every 3 minutes.

6. All the manual on/off touch will be disabled the the transmitter is in thermostatic mode.

7. Press the Auto button to exit the thermostatic mode (beep once). The “TSTAT” and SET temp icon will

disappear on the lower LCD display. The transmitter will be in the manual on/off mode

Child-proof protection:

50D0093 Rev 3 May 2005 Page 8 of 11 Ambient Technologies

ADivision Of

1. Touch both sides of the groove surface with your two index fingers simultaneously for at least 3 seconds to

enter child-proof mode. Once you hear two (2) beeps and the child proof icon appears on the LCD display,

the child proof mode is activated. You will not able to turn the appliance on or off in this mode.

2. Always place both fingers on the middle of the groove surfaces to ensure a proper touch.

3. Child-proof protection is not available in Thermostatic mode.

4. To deactivate child proof, repeat step 1. You will hear two (2) beeps and the child proof icon will

disappear.

Safety Touch Auto Shut Off:

1. If a metal object, (i.e. car key) or your hand is resting continuously for more than ten (10) seconds on either

side or both side of the groove surfaces , the transmitter will emit three (3) beeps and send an off signal to

turn off the appliance. Once the object is removed from the groove surfaces, the transmitter will remain

in the off state until your next valid touch. Never leave anything on top of the surface of the touch light

transmitter to prevent undesirable operation.

2. This feature will be disabled in Thermostatic mode.

50D0093 Rev 3 May 2005 Page 9 of 11 Ambient Technologies

ADivision Of

Low-battery detection:

1. Battery voltage is checked once

a minute. When the battery

voltage drops to a certain level,

the low-battery warning will

come on, and the transmitter

will emit three (3) beeps and

send signals to turn off the

appliance. The transmitter will

not function anymore until new

batteries are installed. If the

battery is too low, the three (3)

beeps may not be heard.

2. When the batteries are low, the

LCD shows a blinking low

battery indicator.

3. Change the battery every six

months before the battery is too

weak for normal operation. TURN THE UNIT OFF BEFORE REPLACING BATTERIES.

Touch Light Transmitter Thermal Shutdown:

1. If transmitter measures a room temperature

exceeding 99 degrees Fahrenheit, the LCD will

display “HI”, emit three (3) beeps and send an

off signal to turn off the appliance.

2. Transmitter will not function until the room

temperature has dropped below 99 degree

Fahrenheit.

3. If transmitter measures a room temperature less

than 40 degrees Fahrenheit, the LCD will

display “LO”, and no signals will be sent to

turn on the appliance.

Receiver:

Slide Switch:

1. ON position: the system will remain on until the slide switch is placed in the OFF or RS position.

2. RS position: the system will only operate if the remote receiver receives a signal from the transmitter.

3. OFF position, the system is off. The slide switch should be placed in the OFF position if you will be

away for an extended period of time. If the remote receiver is mounted out of children’s reach, the OFF

position also functions as a safety device by both turning the system off and rendering the receiver

inoperable.

TESTING YOUR NEW REMOTE CONTROL SYSTEM

1. Light your gas appliance following the appliance lighting instructions that came with the appliance.

Confirm that the pilot light is on; it must be in operation for the remote control to operate the main gas

valve. Appliance control knob must be in the ON position. Appliance ON/OFF switch must be in OFF

position.

2. Slide the 3 position button on the remote receiver to the ON position. The main gas flame should ignite.

50D0093 Rev 3 May 2005 Page 10 of 11 Ambient Technologies

ADivision Of

3. Slide the button to OFF. The flame should extinguish (the pilot light will remain on).

4. Slide the button to RS (the center position), then touch the transmitter to turn the system to ON. The main

gas flame should ignite.

5. Touch the transmitter to turn the system to OFF. The flame should extinguish (the pilot light will remain

on).

TROUBLESHOOTING

Symptom Causes Action

1. LED light on

receiver blinking or

battery icon on LCD

on transmitter.

2. LCD display is

blank

3. LCD display shows

“funny” display

1. Low Battery 1. Replace batteries. Change

batteries every 6 months.

2. Check battery installation and

replace batteries.

3. Press Reset button at the back of

the transmitter.

4. Appliance does not

come on after a valid

touch (beep)

1. Wiring / Electrical Connections 1. Slide the switch to ON, if

appliance comes ON, wiring is not

the cause.

2. If appliance does not come on,

check wiring connections.

2. Privacy (DIP) switch setting on transmitter

does not match receiver

1. Make sure the transmitter and

receiver have the same DIP switch

settings.

3. Transmitter measures temperature exceeding

99 degrees Fahrenheit and shows “HI” on LCD

1. Move transmitter to a cooler

place and wait until temperature

drops below 99 degree.

4. Distance between the transmitter and receiver

is more than 20 feet

1. Make sure the operating distance

is less than 20 feet

5. Receiver cannot

receive signal.

1. Receiver is installed in an enclosure 1. Make sure the receiver is not

located inside an enclosure.

WARNING: Changes or modifications to this unit not expressly

approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with instructions,

may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

Table des matières

Autres manuels Ambient Télécommande

Ambient

Ambient NanoLockit Guide de dépannage

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation