Ambient Technologies RCSITEA Manuel utilisateur

50D0111 RCSITEA Installation & Operating Manual

Rel 1.0 April 2009 Page 1 of 10 Ambient Technologies

A Division Of Monessen Hearth Systems

RCSITEA

Thermostatic On/Off, Flame Height Adjustment and Blower

Remote Control– 120VAC

INSTALLATION AND OPERATING INSTRUCTIONS

CAUTION: The RCSITEA is only certified to be used on vented heater rated equipment.

This remote control system provides a safe, reliable and user-friendly remote control for millivolt valve gas

appliances, blower speed and flame height adjustment. The system can be manually or thermostatically turned on

and off with the transmitter. Always check the appliance home owner’s manual for additional information, or

warnings regarding accessory installation before connecting this remote control system.

Carefully inspect the contents for shipping damage. If any parts are missing or damaged, immediately contact the

dealer from whom you purchased the kit or Ambient Technologies Technical Support at 1 800 398 6195. Do not

attempt to install any part of the kit unless all parts are in good condition. Please keep this booklet for future

reference.

Please check the gas type of the unit to match the current

CONTENTS OF KIT

Description Qty

Transmitter 1

Battery Alkaline AAA (for Transmitter) 3

Receiver (Assembly) consists of : 1

Receiver Box

AC Adaptor for Receiver

SIT Stepper Motor 1

Slide Button-Black (On/RS/Off) 1

Wall Cover Plate-Black 1

Wire Nuts 2

Plug-In Wiring Assembly for SIT mV Valve– 22” Inches 1

Plug-In Wiring Assembly for SIT Hi/Lo Regulator – 10” Inches 1

Velcro (Loop and Hook) 1

Installation Instructions 1

#8 Screw for sheet metal, Black 2

FEATURES/SPECIFICATIONS

•Easy Access Thermostatic Control

•Battery Powered Transmitter

•Low battery Indication for Transmitter

•Compact 120 VAC Adapter with 30” Wire

•Three Speed Control for Blower with Blower Type Selection

•Three Flame Height Settings

•Programmable Timer to Turn Blower on and Off

•Child Proof Lock-out

•16 Security Codes

•6 hour Shut Down (Optional) on Receiver

50D0111 RCSITEA Installation & Operating Manual

Rel 1.0 April 2009 Page 2 of 10 Ambient Technologies

A Division Of Monessen Hearth Systems

•Quick Disconnect Wiring Assembly

•Reset Button for transmitter

WARNING

Important Safety Information

•Read this manual thoroughly prior to installing, programming or operating any remote control.

•This remote control system is designed for use with a millivolt gas valve system with blower. Do not use

this remote control system on applications with voltages above 24 Volts AC/DC and 1 amp current.

•This remote control system requires three (3) “AAA” alkaline batteries to power the transmitter. The

receiver is powered by external AC Adapter.

•Wiring must conform to appliance requirement and building codes/ordinances as required by local and

national code authorities having jurisdiction.

•Do not short (or jumper) across the gas valve terminals to test the remote control installation. This could

damage the unit and void the warranty.

•This remote control system should only be used as described in this manual. Any other use is not

recommended and will void the warranty.

NOTE

Due to the sensitive temperature monitoring components in the transmitter, it is necessary to

allow the transmitter to stabilize to room temperature before accurate room temperatures are

displayed. If the transmitter is activated from a severe cold condition, allow 15 minutes for

accurate temperature readings to appear on the LCD display.

WARNING

Turn appliance OFF and allow to cool before installing or servicing. DO NOT connect

110-120 VAC wiring to the milli-volt gas control valve. The remote operator must be installed

exactly as outlined in these instructions. Read all instructions completely before attempting

installation. Follow instructions carefully during installation. Any modification of

components will void the warranty and may cause a fire hazard.

WARNING

Turn appliance OFF (at the appliance or remote receiver) if you are away from your house for

an extended period of time. Never leave anything on top of the surface of the transmitter.

INSTALLATIONS

Remote Receiver:

The remote receiver may be installed in the appliance per the appliance homeowner’s manual. Refer to the

Homeowner’s Manual for special installation instructions. Failure to follow the installation instructions found

in the appropriate Homeowner’s Manual will void the warranty and may cause a fire hazard.

50D0111 RCSITEA Installation & Operating Manual

Rel 1.0 April 2009 Page 3 of 10 Ambient Technologies

A Division Of Monessen Hearth Systems

This system comes with an 22 inch two-wire assembly labled “FOR MILLVOLT VALVE ONLY, TP/TH” and an

10 inch four-wire assembly labeled “SIT VALVE ONLY”. Insert the white terminals into the back of the receiver.

The terminal wire blocks can only be installed one way and do not force the terminal plugs into the receiver.

Connect the wiring terminal two (2) ¼” female spade terminals to the appliance valve and four-pin connector to SIT

valve. Refer to the appropriate Homeowner’s Manual for proper wiring connections to the appliance. Your

appliance may have other options to connect wiring from receiver. For applications longer than 22 inches, use 18

gauge wire, 105ºC rated, with no splices. Connect to the two (2) 1/4“ female spade wiring terminals and wire can be

no longer than 20 feet.

WARNING

Speed control module and thermal sensor must be removed before installing receiver and

applying the AC power. Failure to do so may cause the part damage and void the warranty.

Without removing the control module and thermal sensor, they and RCSTEB both will try to

operate the blower at the same and may cause unexpected blower operation or damage.

Before connecting the blower with the receiver, always DISCONNECT SPEED CONTROL MODULE AND

THERMAL SENSOR from your fireplace if they exist as displayed in following diagram:

WARNING

The blower has to be grounded to the body of the fireplace.

50D0111 RCSITEA Installation & Operating Manual

Rel 1.0 April 2009 Page 4 of 10 Ambient Technologies

A Division Of Monessen Hearth Systems

WARNING

STOP: Make sure 120VAC fan and SIT valve are correct. If not wired correctly, this could

cause damage to receiver.

Make sure that the wires do not contact the appliances any place other than at the terminals.

Exposure to temperatures higher than 105C (250ºF) may cause the receiver to malfunction

and cause possible fire hazard.

SIT mV Valve

Hi/Lo Regulator

50D0111 RCSITEA Installation & Operating Manual

Rel 1.0 April 2009 Page 5 of 10 Ambient Technologies

A Division Of Monessen Hearth Systems

Back of the Transmitter

Battery

Door

Tab

Remote Transmitter:

Installing Batteries:

The remote transmitter uses three (3) “AAA” batteries.

To install batteries,

1. Press down the battery door tab and pull out to remove the battery

door.

2. Install the batteries as indicated on transmitter.

3. Close the battery door by snapping in place.

4. When three batteries are installed, the transmitter will initialize for 10

seconds and then is ready for use.

5. The batteries should be replaced at least once every 6 months or

when the low battery icon indicator is displayed.

Setting Privacy (DIP) Switch on Receiver and Transmitter:

The remote receiver and transmitter privacy (DIP) switches are preset at the factory. In the event of activation or

interference from other nearby transmissions, reset the code using the following procedures:

1. There are four switches on the transmitter and seven switches on the receiver (see figure below). Switches

#1, #2, #3 and #4 on both transmitter and receiver are privacy switches and #5, #6, #7 on the receiver are

blower switches.

2. Slide the privacy code switches (#1, #2, #3 and #4) on the transmitter and receiver to your choice of ON

or OFF position. All switches are preset to “ON” for both the transmitter and receiver.

3. The privacy code switches(#1, #2, #3 and #4) on the transmitter and on the receiver must match in order

for the system to work.

4. To check, press either the On or Off button on the transmitter and the receiver indicator light will blink. If

not repeat step 2.

5. The system is now ready to operate.

NOTE See the optional 6 hour shutdown section and the blower type selection section.

Receiver

Privacy Dip Switch (Need to match)

Transmitter

50D0111 RCSITEA Installation & Operating Manual

Rel 1.0 April 2009 Page 6 of 10 Ambient Technologies

A Division Of Monessen Hearth Systems

WARNING

Do not use two (2) or more remote control systems in the same area with the same dip switch

settings, as they will communicate with each other. This may cause the appliances to

malfunction.

Reset Button:

1. The reset button can be used to reset the transmitter if transmitter is not working properly. The reset

button (recessed) is located behind the battery door cover in the lower left corner of battery comparment.

Using a paper clip, press the reset button and the transmitter will reset and initialize for 10 seconds before it

can be used.

OPERATIONS

Transmitter:

General:

The RCSITEA Remote Control has two (2) operating modes: Manual and

Thermostatic. The control system can be set to temperature ranges between 45°F

and 90°F. The blower speed and flame height can be adjusted in either the manual

and thermostatic mode.

The transmitter will operate the remote receiver from 1foot to a maximum of 30

feet. The distance is reduced when batteries are low or when the receiver is inside a

metal enclosure.

Initial Start-up:

1. After initial power up or when RESET button is pressed, the transmitter is reset.

The reset button is located behind the battery door of transmitter.

2. During system reset, all features of the LCD DISPLAY will be visible. After

one second, the LCD will be initialized. A typical reset display is shown above.

Note that the temperature scale is degree F.

3. When only the "F" is displayed without the number, press On button to select

between °C and °F display. It will exit setting mode automatically after 10

seconds if no key is pressed. The transmitter will send an Off signal after reset.

4. After reset, the transmitter is operating in manual mode. The room temperature

is shown as above.

50D0111 RCSITEA Installation & Operating Manual

Rel 1.0 April 2009 Page 7 of 10 Ambient Technologies

A Division Of Monessen Hearth Systems

Manual Mode:

1. Press the ON button once to turn on the appliance with max flame height.

2. Press the OFF button to decrease flame height. The first two pressing will

decrease flame height to lower level. The third pressing will turn fireplace off.

3. If holding on OFF button for more than 3 second, fireplace will be shut off.

Thermostatic Mode:

1. Press the AUTO/FLAME button to enter the thermostatic mode.

2. In thermostatic mode, press the ON / Δbutton or OFF / ∇button to set the

desired set temperature.

3. Once the setting is completed, the transmitter will automatically turn on the

fireplace when the room temperature is below the set temperature and turn off

the appliance when the room temperature is above the set temperature within 1

degree.

4. There will be a slight delay in the response of the unit (on/off) to a temperature.

Room temperature is monitored every 3 minutes.

5. Press the AUTO/FLAME button to exit the thermostatic mode. The transmitter will be in the manual off

mode and the fireplace will be shut off.

3-Speed Bower Control:

Note: Blower operates with flame on only

1. Press FAN button once to enter blower speed setup mode at low speed

initially and one of the three blade icon will display darken on LCD display.

2. Continue to press FAN button to set up the blower speed you desire.

3. If there is no input within 3 seconds, the new setting will be transmitted to

receiver. If fireplace is on, the blower speed will take effect right away; if

fireplace is off, the receiver will remember this setting and blower is still off.

4. If you continue to press FAN button to the position that all blade is gone, the

FAN icon will disappear and turn the blower off.

Blower On Delay Time and Off Delay Time Setting:

Note: Blower operates with flame on only

1. Hold FAN button for 5 second and two numbers will show up in LCD screen.

The upper one is On Delay Time and the bottom is Off Delay Time.

2. Use the ON / Δbutton to set the desired On Delay Time from 0 to 15 min.

3. Use the OFF / ∇button to set the desired Off Delay Time from 0 to 15 min.

4. If there is no input within 3 seconds, the new setting will be transmitted to

receiver.

5. The default settings for both transmitter and receiver are 5 minutes for On

Delay Time and 8 minutes for Off Delay Time, as shown in this picture.

NOTE The most efficient setting for your fireplace blower is when blower comes

on and off, it is blowing warm air only not hot air. Giving the fireplace as

much time to discharge as much warm air as possible before turning off.

50D0111 RCSITEA Installation & Operating Manual

Rel 1.0 April 2009 Page 8 of 10 Ambient Technologies

A Division Of Monessen Hearth Systems

Flame Height Setting for Thermostatic Mode:

1. Hold AUTO/FLAME button for 5 second and one number and flame icon will

show up in LCD screen, as show in the right figure.

2. Use the ON / Δor OFF / ∇button to set the desired flame height to 1 (Min), 2

(Medium) and 3 (Max)

3. If there is no input within 3 seconds, the new setting will be transmitted to

receiver. This setting only affects auto mode operation.

4. The default setting for transmitter is 2 (Medium), as shown in left picture.

Low Battery Detection:

1. Battery voltage is checked once a minute. When the battery voltage drops to a

certain level, the low-battery icon will display on LCD, and the transmitter will

turn off the appliance. The transmitter will not function anymore until fresh

batteries are installed.

2. When the batteries are low, the LCD displays a low battery indicator. The low

battery indicator will be displayed in any mode.

3. The transmitter will not operate with low batteries. Change the batteries before the batteries are too weak

for normal operation. TURN THE UNIT OFF BEFORE REPLACING BATTERIES.

Child-Proof Protection:

1. Press and hold the ON and OFF buttons simultaneously for 3 seconds to enter

childproof mode as shown in this picture.

2. The transmitter will not send a signal again until childproof mode is deactivated by

pressing the ON and OFF buttons simultaneously for 3 seconds to exit childproof

mode and the Childproof indicator disappears from LCD.

Transmitter Thermal Shutdown:

1. If transmitter measures a room temperature exceeding 99 degrees Fahrenheit, the

LCD will display "HI" and the transmitter will turn off the appliance.

2. Transmitter will not function until the room temperature has dropped below 99

degree Fahrenheit. If transmitter measures a room temperature less than 40

degrees Fahrenheit, the LCD will display “LO” and NO SIGNAL will be sent to

turn on the appliance.

Receiver:

Slide Switch:

1. ON position: the main burner will ignite and blower will come on when Blower on Delay Time is reached

and fan speed has been enabled, the flame height is max; otherwise just burner will ignite until the slide

switch is placed in the OFF or RS position to turn burner off.

50D0111 RCSITEA Installation & Operating Manual

Rel 1.0 April 2009 Page 9 of 10 Ambient Technologies

A Division Of Monessen Hearth Systems

2. RS position: the system will operate if the remote receiver receives a signal from the transmitter.

3. OFF position, the system is off. If fan speed has been enabled blower will continure to operate until Off

Delay Time expires. The slide switch should be placed in the OFF position if you will be away for an

extended period of time. If the remote receiver is mounted out of children’s reach, the OFF position also

functions as a safety device by both turning the system off and rendering the receiver inoperable.

Blower Type Selection:

1. The remote control can work with different type/size of blowers. The three levels of blower speeds

(High/Medium/Low) can be fine tuned using the blower switches. See figure below for location of the

switches.

2. In the event that the blower runs too slow or too fast on Low or Medium, change the blower switch setting

to achieve desired speed levels.

3. Turn on the blower at Low speed with the transmitter and start from STEP 1 (ON/ON/OFF), then follow

the following steps in the chart below to set up the blower switches. The blower speed will decrease when

going through the steps. Stop when the desired speed level of Low is achieved.

4. To asure that the proper Low is selected, run through Low, Medium, High to check all speeds to

achieve the desired best speed levels.

NOTE

It is very important that the Low speed is not too low that to overheat blower motor.

Selection Steps DIP5 DIP6 DIP7

STEP 1 ON ON OFF

STEP 2 (DEFAULT) ON ON ON

STEP 3 OFF ON ON

STEP 4 OFF OFF ON

STEP 5 OFF OFF OFF

WARNING

To avoid overheating the blower when the blower runs too slow, always start from higher

speed (from STEP 1) when adjusting speed levels using the blower switches. And stop trying

the rest of the settings when desired speed level of Low is achieved.

50D0111 RCSITEA Installation & Operating Manual

Rel 1.0 April 2009 Page 10 of 10 Ambient Technologies

A Division Of Monessen Hearth Systems

Optional 6 Hour Shutdown:

5. The receiver comes preset from the factory with a 6 hour shutdown from its last ON or flamer lower

operation. This is done to prevent the appliance from continuing to run if unattended.

6. You may disable this feature if you wish. To disable, change the receiver privacy (DIP) switch #1 to the

OFF position. Make sure the transmitter privacy (DIP) switches are set the same as the receiver. Follow

the instructions on how to set the privacy (DIP) switch setting.

7. By disabling this feature, your appliance may continue to run unattended.

Optional Wall Cover Plate:

1. Receiver snaps into wall cover plate. The wall plate is mounted by using 2 screws provided.

TESTING YOUR NEW REMOTE CONTROL SYSTEM

1. Light your gas appliance following the appliance lighting instructions that came with the appliance.

Confirm that the pilot light is on; it must be in operation for the remote control to operate the main gas

valve and blower. Appliance control knob must be in the ON position, and appliance ON/OFF switch must

be in OFF position.

2. Slide the 3 position button on the remote receiver to the ON position and the main gas flame should ignite.

3. Slide the button to OFF and the main gas flame should extinguish, but the pilot light will remain on.

4. Slide the button to RS (the center position), then press the ON button on transmitter to turn the system ON.

The main gas flame should ignite and blower should come on after the On Delay Time is reached and fan

speed you desire is selected.

5. Press the OFF button on transmitter to turn the system to OFF. The flame should extinguish (the pilot light

will remain on) and blower should be off after the Off Delay Time you set.

TROUBLESHOOTING

Symptom Causes Action

1. Battery icon on

LCD on transmitter.

2. LCD display is

blank

3. LCD display shows

“funny” display

1. Low Battery 1. Replace batteries. Change

batteries every 6 months.

2. Check battery installation or

replace batteries.

3. Press Reset button at the back of

the transmitter.

4. Appliance does not

come on. 1. Wiring / Electrical Connections 1. Slide the switch to ON, if

appliance comes ON, wiring is

not the cause.

2. If appliance does not come on,

check wiring connections.

2. Privacy (DIP) switch setting on transmitter

does not match receiver 1. Make sure the transmitter and

receiver have the same DIP

switch settings.

3. Transmitter measures temperature exceeding

99 degrees Fahrenheit and shows “HI” on LCD 1. Move transmitter to a cooler

place and wait until temperature

drops below 99 degree.

4. Distance between the transmitter and receiver

is more than 30 feet 1. Make sure the operating distance

is less than 30 feet

5. Receiver cannot 1. Receiver is installed in an enclosure 1. Make sure the receiver is not

Table des matières

Autres manuels Ambient Technologies Télécommande

Ambient Technologies

Ambient Technologies RCSTEBA Manuel utilisateur

Ambient Technologies

Ambient Technologies TOUCH LIGHT Manuel utilisateur

Ambient Technologies

Ambient Technologies RCST Manuel utilisateur

Ambient Technologies

Ambient Technologies RCSTE Manuel utilisateur

Ambient Technologies

Ambient Technologies RCB Manuel utilisateur

Ambient Technologies

Ambient Technologies RCBE Manuel utilisateur

Ambient Technologies

Ambient Technologies RCB Manuel utilisateur

Ambient Technologies

Ambient Technologies RCBHC Manuel utilisateur

Ambient Technologies

Ambient Technologies WWTD Manuel utilisateur

Ambient Technologies

Ambient Technologies RCMT Manuel utilisateur

Ambient Technologies

Ambient Technologies RCMT Manuel utilisateur

Ambient Technologies

Ambient Technologies RCMHL Manuel utilisateur

Ambient Technologies

Ambient Technologies WMTD Manuel utilisateur

Ambient Technologies

Ambient Technologies RMSC Manuel utilisateur

Ambient Technologies

Ambient Technologies RCB Manuel utilisateur

Ambient Technologies

Ambient Technologies RTSC Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation