amaran 60x Manuel utilisateur
-1-
IMPORTANT SAFETY INSTRUCTIONS
When using this unit, basic safety precautions should always be
followed, including the following:
1. Read and understand all instructions before using.
2. Close supervision is necessary when any fixture is used by or
near children. Do not leave the fixture unattended while in use.
3. Care must be taken as burns can occur from touching hot
surfaces.
4. Do not operate the fixture if a cord is damaged, or if the fixture
has been dropped or damaged, until it has been examined by
qualified service personnel.
5. Position any power cables such that they will not be tripped
over, pulled, or put into contact with hot surfaces.
6. If an extension cord is necessary, a cord with an amperage rating
at least equal to that of the fixture should be used. Cords rated for
less amperage than the fixture may overheat.
7. Always unplug the lighting fixture from the electrical outlet before
cleaning and servicing, or when not in use. Never yank the cord to
remove the plug from the outlet.
Foreword
Thank you for purchasing "amaran" series of LED photography lights -
amaran 60x.
amaran 60x is amaran series of newly designed high cost performance
lamps. Compact structure design, compact and light,excellent texture.
Has a high performance level, such as high brightness, high indication,
can adjust the brightness, etc. It can be used with the existing
Bowens Mount lighting accessories to achieve a variety of lighting
effects and enrich product usage patterns. So that the product to
meet the needs of different occasions light control, easy to achieve
professional level photography.
-2-
CAUTION
DO NOT TOUCH LED
Light Source Surface
8. Let the lighting fixture cool completely before storing.
9. To reduce the risk of electric shock, do not immerse this fixture
in water or any other liquids.
10. To reduce the risk of fire or electric shock, do not disassemble
this fixture. Contact cs@aputure. com or take it to qualified
service personnel when service or repair work is required.
Incorrect reassembly may cause electric shock when the
lighting fixture is in use.
11. The use of an accessory attachment not recommended by the
manufacturer may increase the risk of fire, electric shock, or
injury to any persons operating the fixture.
12. Power this fixture by connecting it to a grounded outlet.
13. Please remove the protective cover before powering on the
light.
14. Please remove the protection cover before using the reflector.
15. Please do not block the ventilation and do not
look at the light directly when it is powered on.
16. Please do not place the LED lighting fixture near
any liquids or other flammable objects.
17. Only use a dry microfiber cloth to clean the product.
18. Please have the product checked by an authorized service
personnel agent if your product has a problem.
19. The malfunctions caused by unauthorized disassembly are not
covered under the warranty.
20. We recommend only using the original Aputure cable
accessories. Please note that our warranty for this product does
not apply to any repairs required due to any malfunctions of
unauthorized Aputure accessories, although you may request
such repairs for a fee.
-3-
FCC Compliance Statement
21. This product is certified by RoHS, CE, KC, PSE, and FCC. Pleas
operate the product in full compliance with the operation
standards. Please note that this warranty does not apply to
repairs arising from malfunctions, although you may request
such repairs on a chargeable basis.
22. The instructions and information in this manual are based on
thorough, controlled company testing procedures.
Further notice will not be given if the design or specifications
change.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Warning:
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
NOTE:
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try reorient or relocate the receiving
antenna.
SAVE THESE INSTRUCTIONS
-4-
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a different circuit than the receiver is
connected to.
Consult the dealer or an experienced radio/TV technician for help.
This device has been evaluated to meet general RF exposure requirements.
RF Warning Statement:
Check list
When you unbox the product, please make sure all the items listed below are included.
Otherwise, please contact the seller immediately.
AC Power cable(4m) (1 pc)
Cable Tie
Adapter (1 pc)
Bowens Mount
Mini Reflector (1 pc) Battery case(1 pc)
Tips: The illustrations in the manual are only diagrams for reference. Due to the continuous
development of new versions of the product, if there are any differences between the product
and the user manual diagrams, please refer to the product itself.
Tie Down (1 pc)
Protection
Cover (1 pc)
-5-
Product Details
1. Light
Power switch button
Seat button
DC-in connector
Adjusting knob
Bowens Mount
Bowens Mount
Mini Reflector
COB LED
Display
Bowens Mount
Release Latch
-6-
Installations
1. Attaching/detaching the protection cover
2. Installation and removal of Bowens Mount Mini Reflector
Push the lever handle according to the arrow direction shown in the picture, and rotate the
Bowens Mount Mini Reflector into it.Rotating in the opposite direction pulls out the Bowens Mount
Mini Reflector.
* Notice: Always remove the protection cover prior to turning on the light. Always re-install the
cover when packing it away.
3. Setting up the Light
Adjust the lamp body to the appropriate height, rotate tie-down to fix the lamp body on the tripod,
then adjust the lamp body to the required angel, and tighten the lock handle.
Push the handle of the lever in the direction of the arrow shown in the picture, and rotate the cover
to pull it out.Reverse rotation will put the protective cover into.
123123
4. Soft light umbrella installation
5.Battery handle installation
Insert the soft light handle into the hole and lock the lock knob on the hole.
Tighten the lamp body and the battery handle via 1/4 screw, then attach the battery plate or
V-mount battery to the handle with the V-mount lock.
1
2
-7-
2
1
3
-8-
Powered by AC
Powered by DC
The power supply
* Please press the spring-loaded lock button on the power cord to remove the power cord.
Do not pull it out forcibly.
*The batteries are not included. Please press the spring-loaded lock button on the battery plate
to remove the power cord. Do not pull it out forcibly.
12AC 100V-240V
~
~
~
~
-9-
1. Press the power button to turn the light on and off
2. Manual control
Operations
Press the knob for 1.5 second to switch the function between INT/CCT adjustment.
Brightness adjustment:
b. Click the INT adjustment knob to quickly switch the brightness level: 20%→40%→60%→80%→100%→20%→40%→60%→80%→100% cycle switch.
a. Rotate the INT adjusting knob to adjust the brightness with 1% variable, and the brightness
change range is (0-100) %, and display the change of (0-100) % in real time on the LIGHT body
OLED display.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels amaran Équipement d'éclairage
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
