Amano 3500 Series Manuel utilisateur

3500/3600 SERIES

Handling Manual

IMPORTANT:

Please do not return this clock to the retailer. If you

have any questions or need assistance, please call us

toll-free at (800) 253-9836.

For more information about Amano’s complete product line,

visit our web site at http://www.amano.com

1. Installing your time clock

1.1

Remove the cover case from the time clock using the key as

shown in Fig. 1. Turn the key all the way to the right and pull

the cover forward. Lift the entire cover straight up and over

the push bar. Remove the packing materials (cardboard tabs

marked remove) from both sides of the inked ribbon spools as

shown in Fig. 2.

1.2. The time clock may be placed on a table or installed on the

wall. To mount the clock on the wall, insert a screw on the

wall through the key-shaped hole at the top of the back plate

of the time clock. Tighten the two screws located on the bot-

tom of the back plate as shown in Fig. 3.

2. Setting the time and date

NOTE: Do not touch the clock hands.

Insert a blank time card before you begin to verify the time, month and date.

2.1 SETTING THE TIME: Pull up and hold the red-tipped lever.

Put your finger on the white wheel and push clockwise to the

desired time as shown in Fig. 4. Let go of the red-tipped

lever and white wheel. Insert a time card to make sure that

the time is correct as shown in Fig. 5.

NOTE: A=AM; P=PM

If you’re on AM and need PM, you will need to advance the

white wheel 12 hours.

2.2 SETTING THE MONTH: Press down the brass retainer clip

inserted in the MONTH typewheel. This frees up the wheel.

Turn the wheel counterclockwise using the tip of your pen or

pencil (each groove represents one month) until the desired

month shows on the punch as shown in Fig. 6.

NOTE: The month must be advanced every month.

2.3 SETTING THE DATE (1-31): Turn the DATE typewheel coun-

terclockwise using the tip of your pen or pencil (each click

represents one date) until the desired date shows on the

punch as shown in Fig. 7.

NOTE: If the month has 28, 29 or 30 days, you will need to

change the date typewheel to the first of the month.

3. Adjusting your clock for Daylight Saving Time

3.1 Beginning of Daylight Saving Time: Advance the time one

(1) hour using the method described in Section 2.1 (SET-

TING THE TIME) on the first Sunday in April every year.

3.2 End of Daylight Saving Time: There are two ways to adjust

your clock for the end of daylight saving time. You can take

the plug out for more than one hour and set the clock to the

correct time using the method described in Section 2.1 (SET-

TING THE TIME). Or, you can advance the time 23 hours

using the method described in Section 2.1 (SETTING THE

TIME) and adjusting the DATE using the method described in

Section 2.3 (SETTING THE DATE).

NOTE: The clock and typewheels should only be adjusted

forward. Reversing the direction of the clock hands and

typewheels will damage the clock.

4. Replacing the ribbon

When the imprint becomes too light, replace the ribbon using the

following procedure:

4.1 Remove the old ribbon spool by pushing the ribbon spool in

the direction of the arrow as shown in Fig. 8. The ribbon

winding ratchet gear will come out with the ribbon spool.

Remove the ratchet gear from the spool before you discard

the old ribbon.

4.2 Insert the ratchet gear into the new ribbon spool. Insert the

ratchet gear marked “L”into the left spool, and the ratchet

gear marked “R” into the right spool as shown in Fig. 9.

4.3

Set the inked ribbon spools with ratchet gears into the holes of

the frame diagonally. The inked ribbon must be carefully installed

between the ribbon shield and frame as shown in Fig. 10.

4.4 Turn the ratchet gear to take up the slack in the inked ribbon.

NOTE: New ribbons may be purchased from any dealer listed in

the RECOMMENDED DEALER SERVICE NETWORK LIST

that was enclosed in your time clock box.

Specifications

Power supply AC 120V, 60 Hz

Power consumption 0.03A

Ambient temperature -10˚ C ~ 50˚ C (14˚ F ~ 122˚ F)

Humidity 10% ~ 90% (non-condensing)

Clock movement Synchronous motor

Printing Inked ribbon

Imprints Month, Date, Hour & Minute or

Day, Hour & Minute

Dimensions 81⁄4“ (w) x 6“ (d) x 101⁄2“ (h)

(206 mm x 148 mm x 264 mm)

Weight 10.2 lbs. (4.6 kg)

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Amano Horloge

Amano

Amano PIX-10 Manuel utilisateur

Amano

Amano 4700 Series Manuel utilisateur

Amano

Amano TCX-85 Manuel utilisateur

Amano

Amano BX 2000 Manuel utilisateur

Amano

Amano PIX-3000x Series Mode d’emploi

Amano

Amano PIX-75 Mode d'emploi

Amano

Amano BX-1600 Guide de démarrage rapide

Amano

Amano MJR-7000EZ Manuel utilisateur

Amano

Amano CP-3000 Manuel utilisateur

Amano

Amano PIX-21 Manuel utilisateur

Amano

Amano MRX-35 Instruction manuelle

Amano

Amano Time Partner TCX-11 Manuel utilisateur

Amano

Amano BX6000 Manuel utilisateur

Amano

Amano PIX-21 Manuel utilisateur

Amano

Amano MJR-8000 Series Guide de dépannage

Amano

Amano MX-300 Manuel utilisateur

Amano

Amano MTX-30F Instructions d'utilisation d'origine

Amano

Amano NS 5000 Series Manuel utilisateur

Amano

Amano EX-6200 Manuel utilisateur

Amano

Amano EX7500 series Manuel utilisateur

Amano

Amano EX9000 series Manuel utilisateur

Amano

Amano PR600 Series Manuel utilisateur

Amano

Amano TS-3000i Manuel utilisateur

Amano

Amano EX3000N Manuel utilisateur

Manuels Horloge populaires d'autres marques

Silicon Laboratories

Silicon Laboratories SI5324 Manuel utilisateur

Heathkit

Heathkit GC-1005 Manuel utilisateur

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manuel utilisateur

Andrew O'Malley

Andrew O'Malley DOTKLOK Manuel utilisateur

ALGE-Timing

ALGE-Timing ASC3 Manuel utilisateur

Bodet

Bodet Profil 960 Manuel utilisateur

Nixie Clock

Nixie Clock Divergence Meter Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-8256-AL Manuel utilisateur

Mini Gadgets

Mini Gadgets MCPro Manuel utilisateur

Casio

Casio TMR-200 Manuel utilisateur

Progetti

Progetti ILTEMPOSTRINGE Manuel

BVItech

BVItech BV-101 Manuel utilisateur

Progetti

Progetti KALIMERO Manuel

La Crosse Technology

La Crosse Technology WT-3141b Manuel

La Crosse Technology

La Crosse Technology W86531 Manuel utilisateur

Sharp

Sharp SPC900 Manuel utilisateur

La Crosse Technology

La Crosse Technology 404-50447 Manuel utilisateur

Datexx

Datexx DF0063 Manuel utilisateur