Alware Flyer Spider 500X Manuel utilisateur
ALware Quad Flyer Spider 500X
With Lighting System
Instruction Manual
www.alwarerc.com
Introduction:
A novel, manoeuvrable and marvelous Quad Flyer Spider 500X is now released from
ALWARE design ompany! Spider 500X was designed based on Sport Flying and with
Spider shape. Constru t with eight pie es(2 olors) of super bright LEDs, it is easier to
dis riminate different flying dire tions no matter in daylight or night time and makes the
Spider 500X look supper brilliant! Furthermore, with a ollapsible body design, it is more
onvenient for storage and transportation. Unlike other lower level ollapsible design, ea h
arm of Spider 500X ould be folded onveniently without using any tools. Combined with a
2-axises FPV amera mount and four individual spring damper landing gears, Spider 500X
obviously is an advan ed QuadFlyer in the market.
Features:
- Glass fiber sheets and Collapsible body design greatly redu e the damage rate on a
small rash, parts an be repaired easily.
- High manoeuvrability and stability modes an be set freely for Sport Flying or Aerial
Filming.
- Allow the usage with all original ele troni s from GAUI 330X su h as Gyro GU-344,
Motors and ESCs et . Upgraded motors an also be used as to in rease the flying power.
(10In h props are needed to use with original 330X motors.)
- High flight effi ien y with Standard Battery (3S 2000mAh) and 330X motors. 10min or
more flight time an be optained with 10in hes props.
- Ex ellent wind resistan e, the effi ien y and load of the propellers are perfe tly optimized
so a better wind resistan e will be a hieved.
- 2-axises FPV amera mount is in luded for aerial filming.
- Carry bag (is optional).
Specification:
Net Weight: 375g
Total Weight: 900g (with 2200mAh 3S Lipo battery)
Length: 500mm (between two Diagonal motors)
Flight time: 10mins (with GAUI S orpion 2208-1050kv motor, 10 In h Props & 2200mAh
3S Lipo)
www.alwarerc.com
Parts List:
A: Spider Arm Frames x8
B: Arm Ribs x8
C: Landing Gears x4
D: Motor Mounts x4
E: Central Frames x2
F: Eye Frames x2
G: Screw Package x1
H: FPV Package x1
Supper Light LED system (with 3
cells Lipo balancer connector) x1
Screw Package FPV Pack
G1:
-Hex Alu Rod 39mm x8pcs
-Round Alu Rod 35mm x24pcs
-Round Alu Rod 16mm x8pcs
H1: FPV Side Frames x2pcs
H2: FPV Stand x1pcs
H3: Servo Mount x1pcs
H4: Pan Axis Frame x1pcs
www.alwarerc.com
G2:
-Tension Spring 0.6x4.9x18mm x4pcs
-Tension Spring 0.6x4.9x22mm x4pcs
-3x7x3mm Flange Bearing x4pcs
-M2 Nut x2pcs
-M3 Nut x4pcs
-Washer 2x5x0.5mm 18pcs
G3:
-M2x6 Hex Cap Screws x34pcs
-M2x8 Hex Cap Screws x48pcs
-M3x4 Hex Cap Screws x8pcs
-M3x8 Hex Cap Screws x4pcs
G4: (Spare Parts)
-M2x6 Hex Cap Screws x2pcs
-M2x8 Hex Cap Screws x2pcs
-M2 Nuts x2pcs
-M3 Nuts x1pcs
-Washer 2x5x0.5mm x2pcs
H5: FPV Mount Lock x2pcs
H6:
-Linkage Rod x1pcs
-Ball-Link x2pcs
-Ball x2pcs
-M2x6 Hex Cap Screws x2pcs
H7:
-M2x4 Hex Cap Screws x2pcs
-M2x6 Hex Cap Screws x7pcs
-M2x8 Hex Cap Screws x5pcs
-M2x18 Hex Cap Screws x6pcs
-M2 Nuts x20pcs
-Washer 2x5x0.5mm x2pcs
-Damper Rod (short) x05pcs
-Damper Rod (long) x1pcs
Important Notes for the assembly steps:
−, it is very important to apply RC Threadlo ker to every
s rews when fixing metal parts in luding metal Nuts, otherwise a serious hazard
may be happened during the flying time.
−Don't over tighten any s rews, or some parts may be damaged permanently.
−Some of the assembly dire tion is unique and important, please follow the
assembly dire tion shown on the photos, otherwise you may fail to omplete the
rest steps.
www.alwarerc.com
Assembly Instruction Steps:
Step 1.
Prepare 1x Landing Gear, 1x
(3x7x3mm)Flange Bearing, 1x M3x8 Hex
Cap S rew and 1x M3 Nut.
Step 2.
Insert the M3x8 Hex Cap S rew through the
bottom hole of the Landing Gear and a
Flange Bearing, then tighten it with a M3
Nut.
Step 3.
The “flange” of the Flange Bearing should
be lose to the Landing Gear frame. Adjust
the tightness of the Hex Cap S rew as to let
the Flange Bearing to rotate smoothly.
Step 4.
Repeat step 1-3 as to omplete other 3
pie es of Landing Gear Frames with Flange
Bearings.
www.alwarerc.com
Step 5.
Prepare 2x Spider Arm Frames, 2x Hex Alu
Rod 39mm, 5x Round Alu Rod 35mm, 4x
M2x6 Hex Cap S rews and 5x M2x8 Hex
Cap S rews.
Step 6.
Se ure a Hex Alu Rod onto one end edge of
the Spider Arm Frame using 2x M2x6 Hex
Cap S rews.
Step 7.
Maintain the Hex Alu Rod parallel to the end
edge of the Spider Arm Frame while
tightening the s rews.
Step 8.
Se ure another Hex Alu Rod onto another
Spider Arm Frame using 2x M2x6 Hex Cap
S rews. (Remarks: the assembly direction
must be as same as the photo shown
above.)
www.alwarerc.com
Step 9.
Se ure 5 pie es of Round Alu Rod 35mm to
the either side of the Spider Arm Frame with
5p s M2x8 Hex Cap S rews. (Remarks: the
assembly direction is important and
unique!)
Step 10.
Prepare the assembly finished at step 9, 2x
Arm Ribs, 1x Motor Mount, 1x Landing Gear
Assembly finished at step 4, 2x Round Alu
Rod 16mm and 5x M2x8 Hex Cap S rews.
Step 11.
Insert the Motor Mount onto the Spider Arm
Set with Alu Rods installed.
Step 12.
The assembly dire tion for the Motor Mount
is unique and important.
www.alwarerc.com
Step 13.
Bend and insert an Arm Rib onto the upper
side of the Spider Arm Set.
Step 14.
The end side of the Arm Rib with a small
hole should be pla ed oppose to the Motor
Mount. (Remarks: the assembly direction for
the Arm Rib is important and unique!)
Step 15.
Prepare a GAUI 10A ESC(not in luded) to
get ready to pla e inside the Spider Arm
Assembly. (Other brands of SCs could
also be used, installation for large SCs
please refer to step 19.)
Step 16.
Pla e the 10A ESC under the Arm Rib
Frame installed on the Spider Arm as shown
above.
www.alwarerc.com
Step 17.
Insert the se ond Arm Rib onto the lower
side of the Spider Arm Set. The end side of
the Arm Rib with a small hole should be
pla ed oppose to the Motor Mount.
(Remarks: the assembly direction for the
Arm Rib is important and unique!)
Step 18.
Spider Arm Assembly will look like the photo
shown above after the previous steps.
Step 19.
Remarks: when using large ESCs, simply
pla e the ESC under the Spider Arm and
se ure it with a Zip Tie.
Step 20.
Prepare another side of the Spider Arm to
get ready to join two Spider Arm Frames
together.
www.alwarerc.com
Step 21.
Next insert the Motor Mount into
another side of the Spider Arm at
first.
Step 22.
Twist a M2x Hex Cap Screw into the
Alu Rod under the Motor Mount as to
secure one end side of the Spider
Arms.
Step 23.
Next insert both Arm Ribs to the Spider Arm
Frame and twist the extra four M2x8 Hex
Cap S rews onto the Alu Rods a ording to
the sequen e of the red arrow shown
above.
Step 24.
Total 5 pie es of M2x8 Hex Cap S rews is
now tightened on the red ir le position
shown above. And then prepare 1x Tension
Spring 0.6x4.9x18mm.
www.alwarerc.com
Table des matières
Autres manuels Alware Quadricoptère
