Alto PS 4H Manuel utilisateur
LTO
R
www.altoproaudio.com
Version 1.3 Septemper 2005
English
User's Manual
PS 4H/4HA
1
SAFETY INSTRUCTIONS
1. Read Instructions
All the safety and operation instructions should be read before using the product and retain them for future reference.
2. Water & Moisture
This product should not be used near water and will be protect from atmospheric agents in fixed or temporary installations.
3. Heat
This product should be situated away from heat sources such as radiators, or other devices which produce heat.
4. Liquid Entry
Care should be taken so that liquids are not spilled into the product and that objects do not fall on.
5. Service Assistance
This product should be serviced only by qualified service personnel when :
a. Liquids has spilled or objects have fallen into this product, or
b. This product has been exposed to rain, or
c. This product does not appear to operate normally or exhibits change in performance, or been dropped or itshas
cabinet / chassis damaged.
6. Package
The package of this product has been tested, inspect the package before open, if any damage is found, notify to
your dealer.
7. Hearing
This product produce high acoustic levels may cause permanent hearing loss, (SPL in for a defined period of time).
8. Installations
This product should be installed on the floor with a specific stand, according to the max weight, or in suspension
with a five points included in the cabinet (M10 1.5PH Length 30mm).
The suspension of more speaker cabinet in a vertical array is NOT advised.
"Electric discharge"
This symbol, alert you to the presence of uninsulated dangerous voltage inside the product which constitutes aenclosure,
risk of electric shock.
"Exclamatory point"
This symbol, alert the user to the presence of important operating and maintenance instructions the owner's manualin
included to the product.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Disposing of this product should not be placed in municipal waste and should Separate collection.be
2
1. PS 4H PASSIVE SPEAKER CABINET QUICK START
Stereo
Power Amplifier
Speaker Cable
Tripod
Mount
Left
Main Mix
Output
Right
Main Mix
Output
Mixer
Tripod
Mount
Speaker Cable
Make all initial connections with all the equipment powered off, and ensure that all the main volume controls are turned
completely down.
1). Connect one side of the speaker cable to the output CHA/CHB or Binding Post of your stereo power amplifier and
the other side to the input socket of your speaker cabinet.
2). Complete other connections as illustrated.
3). Turn on your mixer first, then the stereo power amplifier.
4). Turn up the volume controls of your amplifier to about 70%.
5). Use PFL function to get the proper input level for the mixer, and adjust the main mix level control to manipulate
the output level.
6). After using, turn off your stereo power amplifier first, then the mixer.
-. CONNECTION PLATE
(1) INPUT
(2) THRU
(1) (2)
INPUT THRU
LINK
SOUND REINFORCEMENT SPEAKER SYSTEM
POWER HANDLING:
AES - 250 Watts
PEAK - 500 Watts
IMPEDANCE:
4 ohms nominal
DESIGNED AND DEVELOPMENT IN ITALY
SERIAL
MODEL
PS 4H
LTO
R
Receive the power coming from an external power amplifier.
(SPK +1/-1 connected; +2/-2 not connected)
Direct LINK for connect in parallel a second speaker cabinet.
(SPK +1/-1 connected; +2/-2 not connected)
Besides, the passive crossover included the electronic protection
on the driver.
3
(1) BI-POLAR MAIN POWER SWITCH
(2) AC POWER SOCKET WITH MAIN FUSE
(3) GROUND SWIT H
(4) SIGNAL LIMIT, GREEN/RED LED
(5) LINK OUT ON XLR CONNECTOR
(6) LINE /MIC INPUT ON CONNECTOR
(7) MAIN CONTROL
C
VOLUME
COMBO
(3)
(5)(6) (7)
(4)
2. PS 4HA ACTIVE SPEAKER CABINET QUICK START
Signal Cable
Power Cord
Tripod
Mount
Main Mix
Left
Output
Mixer
Tripod
Mount
Power Cord
Right
Output
Main Mix
Signal Cable
Make all initial connections with all the equipment powered off, and ensure that all the main volume controls are turned
completely down.
1). Connect one side of the signal cable at your audio mixer into output left /right (with Stereo-Jack or XLR) and the
other side of the cable into the line input (COMBO) of your active speaker cabinet (with Stereo-Jack or XLR).
2). Connect the power cord to mains.
3). Turn on your mixer first, then the active speaker cabinets.
4). Turn up the volume control of the active speaker cabinets.
5). Use PFL function to get the proper input level for the mixer, and adjust the main mix level control to manipulate
the output level.
6). After using, turn off your active speaker cabinets first, then the mixer.
-. CONNECTION PLATE
(1)(2)
SIGNAL
LIMIT
SHIELD
LTO
R
BAL
LINKINPUT
VOLUME
PS 4HAPS 4HA
MAX MIN
MIN MAX
L
I
N
E
M
I
C
PUSH
1
3
2
NEW TIDE
ACTIVE SPEAKER CABINET
BI-AMP. POWER AMPLIFIER
PROCESSORDSP
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
"WARNING"
POWER
MODEL
SERIAL
230V 50Hz
Useonly with a 250V fuse
4
3. SUSPENSION POINT
The PS 4H/4HA speaker cabinet also provides the suspension
points for fixed installation. How to use them?
First, open the dust covers, and the next, mount the flying rings
to the suspension points (M10 1.5PH LENGTH: 30mm).
For further details, please refer to the right illustration.
Suspension Point
Eyebolt
Dust Cover
4. TECHNICAL SPECIFICATIONS
Descriptions
Powered System type
LOW Output Power
HIGH Output Power
Max SPL at 1m
Frequency Response
Impedance Low - High
Crossover Frequency
Protection Low - High
Low - Frequency
High - Frequency
Horn Coverage H V
Input Sensitivity
Input Impedance
Connectors
Plastic Reinforced Cabinet
Hardware Suspension
Amplifier Protections
External Control
Power Supply
Dimensions H W D
Net Weight /
Gross Weight lbs/kg
Shipping Volume
kg lbs
PS 4HA
Bi-Amp. With DSP processor
300W RMS Class H
100W RMS Class AB
121.5dB SPL calculated
50Hz / 20kHz +/- 10dB
Low 4Ohm - High 8Ohm
2000Hz - DSP Processor
DSP Lim./Comp. each sections
12" / 318mm - 2.5" voice coil
90 H 45 V
Line + 4dB / 1.23V
30kohms Balanced -
15kohms Unbalanced
Input with Combo/Link with XLR
Trapezoidal & Monitor shape
Six suspension points
Soft Start - Short Circuit -
DC voltage - Thermal Protection
Mic/Line Vol.-Clip-Ground Switch.
230Volt / 115Volt 50 /60Hz
660mm 396mm 384mm
(26" 15.6" 15.1")
23.38kg / 51.54 lbs
26.06kg / 57.38lbs
4.83CFT
Descriptions
System type
Continuos Power
Peak Power Rating
Sensitivity at 1W, 1mt
Max SPL at 1mt
Frequency Response
Impedance
Crossover Frequency
Lower - Frequency
High - Frequency
High Frequency Protection
Dimensions H W D
Net Weight /
Gross Weight lbs/kg
Shipping Volume
kg lbs
PS 4H
2 - way vented box
250 Watt AES Standard
500 Watt Peak
97dB SPL
121dB SPL Calculated
55Hz / 20kHz +/-10dB
4 ohm or 8 ohm
2000Hz 12 / 24dB/Oct
12" / 318mm - 2.5" voice coil
1.35" Compression-driver
Electronic Dynamic Protection
660mm 396mm 384mm
(26" 15.6" 15.1")
19.2kg / 42.33lbs
21.67kg / 47.77lbs
4.83CFT
The AES 2 - 1984 Standard specification by Audio Engineering
Society, is representative and commonly used for the measure
in Professional Sound Reinforcement.
It is defined as the square of the RMS voltage generated with a
pre-defined and band-passed Pink Noise Signal, applied con-
tinuously for 2 hours, on the assembled speaker cabinet.
In this way, the declared power of ALTO passive speaker cabinet,
is comparable to the RMS voltage value, measured on the equiva-
lent power amplifier for the same value of impedance.
1.35" Compression-driver
NF01971-1.3
No. 1, Lane 17, Sec. 2, Han Shi West Road, Taichung 40151, Taiwan
http://www.altoproaudio.com Tel: 886-4-22313737
c
All rights reserved to ALTO. All features and content might be changed
without prior notice. Any photocopy, translation, or reproduction of part of this
manual without written permission is forbidden. Copyright 2005 SEIKAKU GROUP
SEIKAKU TECHNICAL GROUP LIMITED
Table des matières
Autres manuels Alto Intervenants
Alto
Alto Elvis Series Manuel utilisateur
Alto
Alto OEX900 Manuel utilisateur
Alto
Alto IPA Music System Manuel utilisateur
Alto
Alto Spectrum PA Manuel utilisateur
Alto
Alto OEX-400 Manuel utilisateur
Alto
Alto PAM5 Manuel utilisateur
Alto
Alto ELVIS SPEAKER Manuel utilisateur
Alto
Alto TOURMAX SX115 Manuel utilisateur
Alto
Alto ELVIS SPEAKER Manuel utilisateur
Alto
Alto TS115 Vibe Manuel utilisateur
Alto
Alto TSL115 Manuel utilisateur
Alto
Alto MIXPACK 10 Manuel utilisateur
Alto
Alto ELVIS 12 MKII Manuel utilisateur
Alto
Alto EQU231VU-MKII V2 Manuel utilisateur
Alto
Alto AMX 180FX-USB Manuel utilisateur
Alto
Alto BLACK 15SUB Manuel utilisateur
Alto
Alto TX10 Manuel utilisateur
Alto
Alto RMX1008 DFX Manuel utilisateur
Alto
Alto Busker Manuel utilisateur
Alto
Alto ELVIS 10 Manuel utilisateur
Manuels Intervenants populaires d'autres marques
Bowers & Wilkins
Bowers & Wilkins 4 Manuel utilisateur
Sonance
Sonance SONOS OUTDOOR Series Manuel utilisateur
Electro-Voice
Electro-Voice EVID FM4.2 Manuel utilisateur
Pioneer
Pioneer XW-HTD630 Manuel utilisateur
Onn
Onn BWA16AA002 Manuel utilisateur
HP
HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur