Alpine HDS-990 Manuel utilisateur
WarningPoints for Safe UsePlease read this manual carefully before using the machine and system components. This manual contains instructions on how to use this product safely and effectively. If failure to follow the instructions in this manual causes malfunctions, Alpine will not assume any responsibility.This manual uses various icons to explain how to use this product safely, and reminds you to pay attention to the dangers that may be caused by improper connection and operation. The meaning of these icons will be explained below. A complete understanding of the meaning of these icons is very important for the correct use of this manual and this system.Do not use any features that will distract you while drivingDo not disassemble or modifyThe volume must be maintained at a level where the noise outside the car can be heard while drivingInaudible emergency vehicle sirens and road warning signals (train intersections, etc.) are very dangerous and may cause accidents. In addition, excessive volume may cause hearing loss.This product is only suitable for cars with 12V negative groundingOtherwise, it may cause a fire and other accidents. Small objects such as bolts or screws should be kept out of the reach of childrenSwallowing small objects may cause serious injury. Once swallowed by mistake, please immediately medical. When replacing the fuse, you must choose a fuse with the correct ampere valueOtherwise, it may cause a fire or electric shock.Do not block the ventilation holes or heat sinkOtherwise, it may cause internal heat build-up and may cause a fire.This product can only be used in 12V mobile applicationsIf used in non-designed applications, it may cause fire, electric shock or other injuries.Make the correct connectionIf it is not connected properly, it may cause fire or product damage.Before wiring, disconnect the cable from the negative terminal of the batteryOtherwise, it may cause electric shock or injury due to electrical short circuit.WarningIt is very dangerous to operate this system while driving. The user should stop before operating the software.Road conditions and laws take precedence over the information displayed on the map: When driving, you should abide by actual traffic restrictions and conditions.This software is specially designed for this machine and cannot be used in combination with other hardware.This symbol indicates important instructions. Failure to heed these instructions can result in serious injury or even death.WarningAny function that affects your concentration should only be used after the car has come to a complete stop. To use these functions, please park Otherwise, it may cause an accident, fire or electric shock. your vehicle in a safe place first. Otherwise, an accident may result. Instructions1-ENEN
Do not use bolts or nuts in brakes or steering systems for grounding connectionsNever use bolts or nuts used in brakes or steering systems (or any other safety-related systems) or fuel tanks for installation or grounding connections. The use of such parts will cause the car controller to fail, resulting in fire and so on.Do not install on the steering wheel or gear lever, etc., which may hinder the operation of the carOtherwise, it will obstruct the front line of sight or obstruct moving parts, etc., causing serious accidents.When there is a problem, please stop using it immediatelyMake sure to use only designated accessories. The use of non-designated parts may cause internal damage to the device, or it may not be securely installed in place. This can cause parts to loosen and cause danger or product failure.Arrange the wires to avoid crimping or being squeezed by sharp metal edgesThe arrangement of wires and cables should be far away from moving parts (such as seat tracks) or sharp edges or corners. This will avoid crimping and damage to the wires. If the wiring passes through a metal hole, a rubber gasket should be used to prevent the wire insulation from being cut by the edge of the metal hole.Do not install in high humidity or dusty locationsAvoid installing the device in a location with high humidity or dust. Moisture or dust invades the device and can cause product failure.PrecautionsProduct cleaningPlease use a dry soft cloth to clean the product regularly. If the dirt is difficult to remove, soak a soft cloth with water only. Any other solvent may dissolve.TemperatureBefore turning on the machine, please make sure that the temperature in the car is between +60°C and -20°C.MaintainIf you encounter a problem, do not repair it yourself. Please return this product to an authorized Alpine dealer or the nearest Alpine service center for repair.Installation locationThis machine cannot be installed in any of the following places:Near direct sunlight and heat sourcesPlaces with high humidity and near water sourcesDusty placesLocations subject to severe vibrationNoticeThis symbol indicates important instructions. Failure to heed these instructions may result in injury or major property damage. from becoming obstructive while driving. Cables or wires that obstruct or hang on the steering wheel, shift lever, brake pedal, etc. are extremely dangerous.Do not splice cablesDo not cut the cable insulation to supply power to other equipment. Otherwise, the current carrying capacity of the wire will be exceeded, resulting in fire or electric shock.Do not damage the pipe or wiring when drillingWhen drilling holes in the chassis for installation, be careful not to touch, damage or obstruct the pipes, fuel lines, fuel tanks or wires. If you don't pay attention, it can cause fire. Otherwise, it may cause personal injury or damage to the product. Please return this product to an authorized Alpine dealer or the nearest Alpine service center for repair. Ask professionals for wiring and installationThe wiring and installation of this product require Use designated accessories and install securelyDo not let the cable be entangled with surrounding objectsArrange the wires and cables in accordance with the requirements of the manual to prevent them professional skills and experience. For safety reasons, please contact the dealer where you purchased the product for installation.2-EN
The Bluetooth® word mark and logo are registered trademarks held by Bluetooth SIG, Inc. Alpine Electronics has obtained permission to use the word mark and logo, and other trademarks and trade names belong to their respective owners.*Appropriate recycling channels should be adopted for the disposal of electronic products to reduce electronic waste pollution.Copyright Notice3-ENEN
Power CableHigh Level Input CableUSB Extension Cable (1.5 m)Commander Extension Cable (2.5 m)Multiple Line CableMounting Brackets ×4Self-tapping Screw×20Machine Screw×8Commander CaseCommanderMain UnitAccessory List4-EN
12345678910111213Connections and Functions
（ ）（ ）
Vehicle's Battery5-ENENDISP.OUTPOW-LEDUSB HOSTMIX PORTHI-LEVEL INPOWERHOST/ACC
Front USB ConnectorUsed to connect U disk, mobile hard disk or USB HUB.Reset Button
Press and hold for 3 seconds to restart the host.
Rear Double USB ConnectorConnect the USB or mobile hard disk through the attached USB extension wire.Commander ConnectorIt can be connected to the controller for play control, volume adjustment, and audio source selection.Power IndicatorThe power-on light is always on, and the power-off light is off.Multiple Line connectorIncluding 1 set of 3.5mm socket audio input interface, 3 sets of RCA audio output interface, optical output interface, coaxial output interface, square control interface, Alpine system matching interface (for DSP product connection) and USB 2.0 interface.High Level Input ConnectorConnect to the power output of the car audio player.Input Select SwitchWhen dialed to the "ACC" end, ACC starts the machine; when dialed to the "HOST" end, the high level input signal FL-/FL+ starts the machine.Power Output ConnectorConnect the car battery.Speaker Output Connect speakersMultiple LineExternal function expansion interface.Car Audio PlayerConnect the car audio player.112234567891110CommanderSystem expansion interface.13Connections and Functions6-EN
KeyUSB: Short press to select the next song; long press for more than 2 seconds to fast forward.Bluetooth audio: select the next song.KeyShort press to switch pause/play; long press for more than 2 seconds to switch random play/single cycle.KeyUSB: Short press to select the previous song; long press for more than 2 seconds to rewind.Bluetooth audio: select the previous song.KeyShort press to mute; long press for more than 2 seconds to shut down.*You can press any key to boot.KeyShort press to select the main audio source: USB, Bluetooth audio, high level or AUX (the default is USB); long press for more than 2 seconds to turn on/off the mixing mode.KeyReturn to the previous level.Hi-Res Indicator The light is only on when the Hi-Res quality song is currently playing, and the light is not on in other quality songs.Rotary EncoderMain interface: Rotate left and right to adjust the volume; short press to enter the song list; long press for more than 2 seconds to enter the setting interface.Setting interface or song list: Short press to confirm the selection.Remote Control Sensor 234169785Location of Controls7-ENEN812345796
Specifications8-ENPower OutputTHD+NS/N (RCA）Input VoltageOutput VoltageInput/Output Sensitivity(RCA)Frequency ResponseChannel SeparationNoiseDynamic RangeGeneralInput ResistanceOutput ResistanceSystem Sampling RateOperating VoltageQuiescent CurrentStandby Power ConsumptionREM Start InputREM Start OutputBoot TimeAmbient TemperatureStorage TemperatureNet WeightHost SizeRated：4Ω, 14.4V, 1kHz, 10%THD4CH×25WMaximum：4Ω, 14.4V, 1kHz, 10%THD4CH×50WRCA：14.4V, 4Ω,1W, A-wt≤0.03%RCA：14.4V, 1KHz. A-wt, 1%THD≥98dBHigh level：14.4V, 1KHz, 1%THD32VppRCA：14.4V, 1KHz, 1%THD8VppHigh level：14.4V, 1KHz, 1%THD28RCA：14.4V, 1KHz, 1%THD12Vpp14.4V, 1KHz, 1%THD1:1.5 (no power amplification)14.4V, 1W, 4Ω20Hz～40kHz (±1.5dB)14.4V, 1KHz, A-wt≥80dB RCA9uVrmsHigh level58uVrms≥100dBHigh level240ΩRCA10kΩRCA51Ω192kHz/32bit9~16V≤3mA (not on state)≤0.1WHigh level (FL+/FL-), ACC optional12V (0.2A）15s-20~70℃-40~85℃0.77kgLength178mmWidth143.6mmHigh50mmPerformanceMusic PlayerInterfaceCapacityMaximum Power ConsumptionFile SystemThe maximum number of songs that can be played Mp3 DecodingWMA DecodingAAC DecodingWAC DecodingUSB 2.0Maximum Support 2TB1.5AFAT16/32, NTFS, exFAT10,000 SongsMPEG Audio Layer-3Windows Media™ Audio".M4a" File in ACC-LC formatMPDG Audio Layer-4FLAC DecodingAPE DecodingDSD DecodingBluetooth Supports Audio FormatsWave Sound FileFree Lossless Audio CodecMokey,s AudioACC/SBC/APTX HD/LDAC
This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard
(s).Operation is subject to the following two conditions:
(1)this device may not cause harmful interference, and (2)this device must accept any interference received,
including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC et aux normes RSS exemptées de licence
d’Industrie Canada. Le fonctionnement est soumis aux deux
conditions suivantes :(1)cet appareil ne doit pas causer d’interférences nuisibles, et (2)cet appareil doit
accepter toute interférence reçue, y compris les interferences pouvant entraîner un fonctionnement indés
Changes or modifications to this unit not expressly approved by the party responsible forcompliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against
harmful interference in a residential installation. This equipment generates,uses and can radiate radio
frequency energy and, if not installed and used in accordance withthe instructions, may cause harmful
interference to radio communications. However, there is noguarantee that interference will not occur in a
particular installation. If this equipment doescause harmful interference to radio or television reception,
which can be determined by turningthe equipment off and on, the user is encouraged to try to correct the
interference by one ormore of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and
compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and
compliance.
cet appareil est conforme à l'exemption des limites d'évaluation courante dans la section 2.5 du cnr - 102 et
conformité avec rss 102 de l'exposition aux rf, les utilisateurs peuvent obtenir des données canadiennes sur
l'exposition aux champs rf et la conformité.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
Cet équipement est conforme aux limites d'exposition aux rayonnements du Canada établies pour un
environnement non contrôlé.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. This equipment should be
installed and operated with minimum distance 20cm between the radiator & your body.
L'appareil a été évalué pour répondre aux exigences générales d'exposition aux RF.Cet équipement doit
être installé et utilisé avec une distance minimale de 20cm entre le radiateur et votre corps.
Autres manuels pour HDS-990
1
Table des matières
Autres manuels Alpine Lecteur multimédia
Alpine
Alpine UTX-M08S Manuel utilisateur
Alpine
Alpine IVA-D106E Manuel utilisateur
Alpine
Alpine IVE-W560BT Manuel utilisateur
Alpine
Alpine HDS-990 Manuel utilisateur
Alpine
Alpine INA-W910R Manuel utilisateur
Alpine
Alpine iXA-W404R Manuel utilisateur
Alpine
Alpine IVA-D900R Manuel utilisateur
Alpine
Alpine UTX-M08 Manuel utilisateur
Alpine
Alpine IVA-D100 Manuel utilisateur
Alpine
Alpine IVE-W530BT Manuel utilisateur
