Alpine ALP411-E Manuel utilisateur
HORIZONTAL
DIAPER
CHANGING
STATION
ALP411-E
USER GUIDE
Known in the industry for excellent products, Alpine Industries
is a manufacturer of innovative, solution-based products for
the commercial and institutional markets worldwide.
Combining commitment to the customer, design innovation and skilled,
dedicated workforces, they have produced a range of products that are an
essential part of every commercial facility. Every product is designed to the
highest standards, enabling you to get your requirements done in a reliable
and cost-eective way.
THANK YOU
FOR YOUR
PURCHASE.
1 Parts Included
2 Hardware Bag
3 Installation Instructions
9 Operation Instructions
10 Maintenance and Cleaning
11 Limited Warranty
12 Disclaimer
Table of Contents
1
CHANGING STATION
Parts Included
Tools Required (Not Included)
Adult Installation Required
• Level
• Measuring Tape
• Power Drill with 7/32”, 1/8” and ½” masonry bits.
• Power screwdriver with bull nose Philips bit.
CAUTION:
• Read all instructions before assembly of Diaper Changing Station.
• Unpack carton and identify all parts
DOOR/WALL PLATE
1
2
2
Hardware
3” WOOD SCREWS (4)
3/4” FINISHING WASHERS (4) TOGGLE ANCHORS (2)
1 ¼” CAPS (4)
A
B E
3” MACHINE SCREWS (2)
CF
3/4” FLAT WASHERS (4)
D
3
Installation Instructions
• One wall stud MUST be located and USED for at least one side of the diaper changing station.
• The diaper changing station CANNOT be heavier than the anchors or walls they are attached to.
• It MUST be firmly secured to support the additional weight of a child.
• Contact an architect or building contractor for further questions.
STEP 1:
A. Locate the wood stud where the left side of Changing Station (1) will be mounted to the wall.
STEP 2:
A. Measure up 42’’ (107cm) from the floor and mark the wall; this locates the top left attachment hole’s
position.
NOTE: Mark on wall MUST be in the center of the wood stud.
STEP 3:
A. Align the hole in the top left corner of Changing Station (1) with the mark on the wall and hold it in
place.
STEP 4:
A. Using a level and measuring tape, mark the remaining three (3) holes.
B. After marking holes, set the Changing Station (1) down on the ground.
STEP 5:
A. Use a power drill and appropriate bit to drill four (4) holes in the wall.
B. This may require two (2) people.
NOTE 1: FOR WOOD STUDS:
• If the finished wall surface is tile or masonry over wood studs, use a 7/32” masonry bit for the pilot hole
until you hit the wood stud, then change it to a 1/8” bit.
• Use Wood Screws (A), finishing Washers (B), and Flat Washers (D) (See Figure A on page 4).
WARNING:
!
4
Installation Instructions
WALL
WOODEN
WALL STUD
FIGURE A
1
D
B
A
5
NOTE 2: FOR USE WITH TOGGLE ANCHORS E:
• If the finished wall surface has wood studs that are not 16” on center, has metal studs, or has an
underlying surface of concrete block, use ½” bit.
• Use Machine Screws (C) and Flat Washers (D) (See Figure B on page 6).
• For holes NOT located in a wood stud, Toggle Anchors (E) MUST be used (See Figure C on page 7).
See “Using Toggle Anchors” section.
STEP 6:
A. Align holes in Changing Station (1) with drilled holes and secure top left corner of Changing Station (1)
to wall stud using the appropriate screw and washer.
B. Continue to secure the three (3) remaining corners using the proper screws and washers as
described in NOTE 1 or NOTE 2.
STEP 7:
A. Ensure all four (4) screws are tight and snap the Caps (F) over the screw heads.
Installation Instructions
ALL 4 OF THESE LOCATIONS
MUST BE USED FOR SAFE
INSTALLATION. THE LOWER
HOLES ENSURE INSTALLATION
THROUGH THE METAL BRACKETS.
WARNING:
!
6
FIGURE B
Installation Instructions
WOODEN
WALL STUD
E
1
D
C
WALL
7
Installation Instructions
USING TOGGLE ANCHORS:
1. Insert the metal end of the Toggle Anchor (E) into the 1/2’’ hole.
2. Slide zip strip down snugly against the wall.
3. Snap o break-away pieces of Toggle Anchor (E) (See Figure C below).
4. Ensure all four (4) screws are tight and snap Caps (F) over screw heads.
5. Align holes on the Changing Station (1) with Toggle Anchors (E) and secure top left corner of the
Changing Station (1) to the wall using Machine Screws (C) and Flat Washers (D).
6. Continue to secure the three (3) remaining corners using Machine Screws (C) and Flat Washers (D).
ZIP STRIP
BREAK AWAY
PIECES
BREAK AWAY
PIECES
TOGGLE
ANCHOR
BEHIND
WALL
WALL
E
FIGURE C
Table des matières
Autres manuels Alpine Accessoires pour bébé
