Allo RemoteControl WHY EVO Manuel utilisateur

WHY EVO

INSTRUCTIONS

Visit our Website: www.alloremotecontrol.com

FIXED CODE DUPLICATING PROCEDURES:

1. While pressing the button 1 of the “WHY EVO”, at the same time press 4 times

the 2 button.

2. Release both buttons. Now the WHY EVO WHITE LED emits a short flash every 2

seconds.

3. Place the original remote control to be programmed in front of the “WHY EVO”, at

about 5 cm of distance (as shown in the picture).

4. Press and retain pressed the button of the original remote control and wait for a

change flash (as a faster flash) of WHY EVO WHITE LED and a change of its color

(BLUE) that confirms the correct learning of code. This step may take a few

seconds and during that the color LED is WHITE.

5. While the BLUE LED is flashing, press the button of the “WHY EVO” where you

want to program the code just learnt, and retain pressed until the LED switches

off and an extended sound “BEEP” for a reconfirmation of the correct code

learning. This step may take some seconds.

6. The copy has been happened with success. Now check on the automation the

correct functioning of the new WHY EVO remote control.

Notes:

• If the WHITE LED flashes only 3 times (of WHITE color) and switches off, the code

has not learnt correctly. Please repeat the operation from the step 1.

• The WHY EVO memory is completely re-writable.

• To duplicate further buttons of WHY EVO, please repeat the operation from the step

ROLLING SIMPLE DUPLICATING PROCEDURES:

1. While pressing the button 1 of the “WHY EVO”, at the same time press 4 times the 2

button.

2. Release both buttons. Now the WHY EVO WHITE LED will emit a short flash every 2

seconds.

3. Place the original remote control to be programmed in front of the “WHY EVO”, at

about 5 cm of distance (as shown in the picture). 4. Press and retain pressed the button

of the original remote control and wait for a change flash (as a faster flash) of WHY EVO

WHITE LED and a change of its color (BLUE) that confirms the correct learning of code.

This step may take a few seconds and during that the color LED is WHITE.

5. While the BLUE LED is flashing, press the button of the “WHY EVO” where you want

to program the code just learnt, and retain pressed until the LED will switch off. The

WHY EVO remote control will emit an extended sound “BEEP” for a reconfirmation of the

correct code learning.

6. The copy has been happened with success.

7. Activate now the correct procedure for the programmed model and insert the new

remote control on the receiver (see the compatibility list present in this manual).

Notes:

• If the WHITE LED flashes only 3 times (of WHITE color) and switches off, the code has

not learnt correctly. Please repeat the operation from the step 1.

• The WHY EVO memory is completely re-writable.

• To duplicate further buttons of WHY EVO, please repeat the operation from the step 1.

Duplicating procedures of WHY EVO TO WHY EVO:

1. While pressing the button 1 of the “NEW WHY EVO”, at the same time press 4 times

the 2 button.

2. Release both buttons. Now the WHITE LED of “NEW WHY EVO” will emit a short flash

every 2 seconds.

3. Place the “SOURCE WHY EVO” in front of the “NEW WHY EVO” , at about 5 cm of

distance (as in the picture 3 at the page 3).

4. Press and retain pressed the button to be programmed of the “SOURCE WHY EVO”

Visit our Website: www.alloremotecontrol.com

Table des matières

Autres manuels Allo RemoteControl Télécommande

Allo RemoteControl

Allo RemoteControl FAAC SLH Manuel utilisateur

Allo RemoteControl

Allo RemoteControl SEA Head 433 2 Manuel du propriétaire

Allo RemoteControl

Allo RemoteControl NICE HSCU2W Manuel utilisateur

Allo RemoteControl

Allo RemoteControl GENIUS JA334 Manuel utilisateur

Allo RemoteControl

Allo RemoteControl CAME T434 Manuel utilisateur

Allo RemoteControl

Allo RemoteControl BERNER Manuel utilisateur

Allo RemoteControl

Allo RemoteControl CARDIN S435 Manuel utilisateur

Allo RemoteControl

Allo RemoteControl SOMFY Keytis Manuel utilisateur

Allo RemoteControl

Allo RemoteControl PROGET ETY 433 4N Manuel utilisateur

Allo RemoteControl

Allo RemoteControl RIB SUN T433 4CH Manuel utilisateur

Allo RemoteControl

Allo RemoteControl ALLDUCKS 6204 Manuel utilisateur

Allo RemoteControl

Allo RemoteControl Prastel SLIM2E Manuel utilisateur

Allo RemoteControl

Allo RemoteControl SOMMER 4004 Manuel utilisateur

Allo RemoteControl

Allo RemoteControl APRIMATIC UNICO RR-SE Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation