Allmatic B.RO X40 DISPLAY Manuel utilisateur

MADE IN ITALY

B.RO X40 DISPLAY

4 channels Rolling Code receiver, with

display.

2/20 6-1620020 rev.0 27/10/2015

ITA ENG FRA ESP DEU POR

ENG

B.RO X40 Display is a 4-channels Rolling Code receiver compatible with all Allmatic Rolling Code remotes. This device has an easy

and intuitive functioning thanks to the display interface and 3 buttons. 4 relay outputs are available with dry contact normally open

(N.O.) and/or closed (N.C.). Outputs can work with 4 different modes: dead man, step by step, timed and timed with delay. Each

output can be controlled by a dedicated wired input or by a single key of a memorized transmitter. The output function is directly

associated to the input command and no to the relay.

The learning of a key of a transmitter can be realized with 3 procedures: default learning (customizable), sequential and advanced.

Power supply 12-24 Vdc/Vac with automatic selection of the voltage.

CONNECTIONS

1-5: wired input (N.O. contact) for relay 1.

2-5: wired input (N.O. contact) for relay 2.

3-5: wired input (N.O. contact) for relay 3.

4-5: wired input (N.O. contact) for relay 4.

6-7: power supply.

8-9: relay output 1 (N.O. contact).

9-10: relay output 1 (N.C. contact).

11-12: relay output 2 (N.O. contact).

12-13: relay output 2 (N.C. contact).

14-15: relay output 3 (N.O. contact).

15-16: relay output 3 (N.C. contact).

17-18: relay output 4 (N.O. contact).

18-19: relay output 4 (N.C. contact).

20: antenna braiding.

21: antenna.

DISPLAY

DOWN

+ -

INPUTS LED

OUT1 OUT2 OUT3 OUT4

IN1 (NO)

COM

IN2 (NO)

IN3 (NO)

IN4 (NO)

POWER SUPPLY

12-24 Vdc-Vac

NC1

COM1

NO1

NC2

COM2

NO2

NC3

COM3

NO3

NC4

COM4

NO4

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

20 21

OUTPUTS LED

RADIO MODULE

MEMORY

ELECTRICAL CONNECTIONS

DESCRIPTION

Please read this instruction manual very carefully before installing and programming your control unit.

After the installation keep this instruction in a safe place for any further consultation.

• The device must not be used by people (children included), whose physical, sensory and mental capacities are reduced, or without

experience or knowledge, unless they could bene!t through the intermediation of a person responsible for their safety, of a

surveillance or of instructions related to the use of the device.

• Children must be kept under surveillance to make sure that they do not play with the device.

• If the power supply’s cable is damaged, it must be replaced by the manufacturer or by his assistance service or in any case by a

person with similar status in order to prevent any risk.

• This instruction manual is only for quali!ed technicians, who specialize in installations and automations.

• The contents of this instruction manual do not concern the !nal user.

• Every programming and/or every maintenance service should be done only by quali!ed technicians.

• The installer must provide the installation of a device (es. magnetothermical switch) that ensures the omnipolar sectioning of the

equipment from the power supply.

REMARKS

3/20

6-1620020 rev.0 27/10/2015

ITA ENG FRA ESP DEU POR

ENG

BBBB

Make sure that the receiver is out from any menu.

The display shows:

Press brieﬂy the UP (+) button.

The display shows:

GUDG

S

Press a key of the transmitter.

The display shows the position in the memory, for example:

GRQH

The display shows:

Otherwise, if the remote is already memorized, a new learning restores the

transmitter to the default values and the display shows:

IRXQG

GUDG

The receiver waits for a new transmitter.

The display shows:

To quit, press brieﬂy the UP (+) button or wait 10s of inactivity.

The device has available 3 modality for the learning of a transmitter:

• Default learning - press brieﬂy the UP (+) button for the activation.

• Sequential learning - press brieﬂy the DOWN (-) button for the activation.

• Advanced learning - press brieﬂy the MENU button for the activation.

ATTENTION: outputs are disabled during the learning.

3.1 - DEFAULT LEARNING

The default learning memorizes all keys of a remote control with a single press of a key.

The memorized transmitter will have the same settings of the default transmitter. The default transmitter is stored in the memory

and his parameters could be personalized inside the modif menu with the selection of the pdef position (see paragraph 4.2).

If the remote is already memorized, a new learning restores the transmitter to the default values.

The receiver exits from the learning phase after 10 seconds of inactivity or with the press of the UP (+) button.

LEARNING OF A TRANSMITTER

NOTE.

The default transmitter leaves the factory with the following settings:

- Key 1 (b01) activates OUT1 output (CH01) with dead man function (F00).

- Key 2 (b02) activates OUT2 output (CH02) with dead man function (F00).

- Key 3 (b03) activates OUT3 output (CH03) with dead man function (F00).

- Key 4 (b04) activates OUT4 output (CH04) with dead man function (F00).

- Keys from 5 to 16 (b05...b16) are with dead man function (F00), but they are not associated to any outputs.

ATTENTION: with the default learning, B.RO OVER and TECH3 PLUS transmitters are associated to outputs in this way:

- Upper key (b01) activates OUT1 output (CH01) with dead man function (F00).

- Central key (b03) activates OUT3 output (CH03) with dead man function (F00).

- Lower key (b02) activates OUT2 output (CH02) with dead man function (F00).

4/20 6-1620020 rev.0 27/10/2015

ITA ENG FRA ESP DEU POR

ENG

BBBB

Make sure that the receiver is out from any menu.

The display shows:

Press brie•y the DOWN (-) button.

The display shows:

VUDG

S

Press a key of the transmitter.

The display shows the position in the memory, for example:

GRQH

The display shows:

Otherwise, if the remote is already memorized, the display shows:

IRXQG

VUDG

The receiver waits for a new key to be memorized.

The display shows:

To change the selected channel, press and release the DOWN (-) button until the

lighting of the corresponding LED.

OUT1, OUT2, OUT3 and OUT4 LEDS indicate the involved channel during the

learning.

For the selection of the channel press and release the DOWN (-) button until the

lighting of the corresponding LED.

To quit, press and release DOWN (-) button until you switch off of all LEDs of the

outputs or wait 10s of inactivity.

3.2 - SEQUENTIAL LEARNING

The sequential learning memorizes the single key of a transmitter and it associates the key on the desired output.

To the stored key is assigned the DEAD MAN function.

The receiver exits from the learning phase after 10 seconds of inactivity or with the multiple press of the DOWN (-) button.

This learning is activated also with the press of the hidden key of a stored remote control. For the selection of the desired output,

press more times the hidden key.

5/20

6-1620020 rev.0 27/10/2015

ITA ENG FRA ESP DEU POR

ENG

BBBB

Make sure that the receiver is out from any menu.

The display shows:

Press brie•y the MENU button.

The display shows:

DUDG

S

Select the location of the transmitter in the memory with UP (+) and

DOWN (-) buttons of the receiver.

The display shows:

Otherwise, if the remote is already memorized in that location, the display shows:

With UP (+) and DOWN (-) buttons it is possible to change the location where a

transmitter is stored.

QHZ

Press a key of the transmitter.

The display shows:

Otherwise, if the remote is already memorized, the display shows:

IRXQG

S

)

Press and hold the MENU button until the display shows:

if the key is already memorized, the display shows the previous function of the

key:

Select the function of the key with UP (+) and DOWN (-) buttons.

)

)

)

&+

Press and hold the MENU key until the display shows:

Enable/disable the key of the transmitter in the channel 1 with UP (+) and

DOWN (-) buttons of the receiver.

If the key is enabled, the display shows:

&+

3.3 - ADVANCED LEARNING

The advanced learning memorizes the single key of a transmitter.

During the learning phase it is possible to set the parameters of the memorized remote control. See paragraph 4for more information

about single parameters.

The receiver exits from the learning phase after 10 seconds of inactivity or with the press of the MENU button.

6/20 6-1620020 rev.0 27/10/2015

ITA ENG FRA ESP DEU POR

ENG

DUDG

The receiver waits for a new key to be memorized.

The display shows:

To quit, press brie•y the MENU button or wait 10s of inactivity.

&+

Press and hold the MENU button until the display shows:

Enable/disable hte key of the transmitter in the channel 2 with UP (+) and

DOWN (-) buttons of the receiver.

If the key is enabled, the display shows:

&+

Press and hold the MENU button until the display shows:

VDYHG

&+

Press and hold the MENU button until the display shows:

Enable/disable hte key of the transmitter in the channel 3 with UP (+) and

DOWN (-) buttons of the receiver.

If the key is enabled, the display shows:

&+

&+

Press and hold the MENU button until the display shows:

Enable/disable hte key of the transmitter in the channel 4 with UP (+) and

DOWN (-) buttons of the receiver.

If the key is enabled, the display shows:

&+

WARNING: the short pressure of the MENU button during the parameter selection returns the process to the previous point. For

example: the brief pressure of the MENU button in channel 1 enabling menu (the display shows CH01) returns the process to the

selection of the function (the display shows F00 or the last function selected).

7/20

6-1620020 rev.0 27/10/2015

ITA ENG FRA ESP DEU POR

ENG

BBBB

To enter inside the base menu, press the MENU button for at least 1 second.

After the MENU button is pressed, the password is requested, if it has been set (see paragraph 4.1.1).

Use UP (+) and DOWN (-) buttons to move inside the items of the menu, while with the long pressure of the MENU button it is

possible to:

• enter the following group of parameters;

• enter the following step of the running process, or !nish the procedure if it is in the last step (the changes are saved;

• enter the change mode, in the case of parameters that can be changed;

• save the parameter just modi!ed.

During the change of the selected parameter, the value starts blinking. It is possible to change its value with the use of the UP[+] and

DOWN[-] buttons. Instead, with a short pressure of the MENU button it is possible to:

• cancel the change of the parameter in progress;

• go to the previous group of parameters;

• go to the previous step of the procedure in progress.

To quit the menu, press brie"y the MENU button until the display shows , or wait 1 minute of inactivity.

MENU DESCRIPTION

PARAM

PARAMETERS OF THE RECEIVER

Sub-menu of the receiver where it is possible to:

- set the password (PWD);

- enable/disable the learning of the transmitters through the buttons in the receiver (HEYB);

- enable/disable the hidden key of the transmitters (HIde);

- set the function associated to a single wired input (Input);

- set the time and the delay of the outputs that are used with Timed function or Timed+Delay function (rtime);

- reset the receiver to default settings (def).

MODIF PERSONALIZATION OF THE TRANSMITTERS

Sub-menu where it is possible to change all the parameters of a remote control that is located in the memory.

TRF

RESET OF THE TRANSMITTERS

It erases from the memory all the memorized transmitters. During this process it is possible to select the type of

coding that you want to set to the receiver:

- biroL: Rolling Code Allmatic;

- sawn: Custom.

SEE

CHECKING MODE OF THE REMOTE CONTROL

It checks if the transmitter is memorized and shows:

- the location in the memory;

- the index of the pressed key;

- the outputs that are associated to the key.

MENU DESCRIPTION

SELECTABLE

VALUES

min-max

DEFAULT UNIT

Pwd PASSWORD

Value for the protection of the menu. 0(OFF)-9999 OFF

HEYb

LEARNINGS

It is possible to enable or disable the learnings of the transmitters

through buttons in the receiver.

ON-OFF ON

HIde HIDDEN KEY (only with biroL coding)

It is possible to enable or disable the hidden key of transmitters. ON-OFF ON

InPUT

PARAMETERS FOR THE WIRED INPUT

With the selection of the wired input (I01, I02, I03 o I04) you can

associate to it the output function (FUnCT):

- 0: Dead Man;

- 1: Step by Step;

- 2: Timed;

- 3: Timed+Delay.

0-3 0

4.1 Param - SUB-MENU FOR PARAMETERS

8/20 6-1620020 rev.0 27/10/2015

ITA ENG FRA ESP DEU POR

ENG

,QSXW

Go to the menu item Input.

The display shows:

Select the wired input using the UP (+) and DOWN (-) buttons of the receiver.

The display shows:

or or or

,

Select the wired input using the UP (+) and DOWN (-) buttons of the receiver.

The display shows:

Press and hold the MENU button

until the display shows:

IXQ&7

,

,

,

Press and hold the MENU button until the parameter blinks.

Select the desired function with the UP (+) and DOWN (-) buttons of the receiver.

Con!rm the change with a long pressure of the MENU button.

,

,

,

,

4.1.1 PWD - PASSWORD

The menu of the receiver can be protected by a password that will be requested at every login attempt.

This is shown in the display with P0000 and the !rst digit blinking. To change the digit you can use the UP (+) and DOWN (-) buttons.

To move to the next digit press brie"y the MENU button. At the end of the procedure, if the password is correct you will enter the

menu, otherwise the display will show: P Err.

After 1 minute of inactivity the password will be re-enabled.

ATTENTION: it is not possible to delete a forgotten password. You will need a recovery procedure by the manufacturer.

4.1.2 Heyb - LEARNINGS

It is possible to enable or disable all the learnings. These are the only active functionality that does not require a password (if

enabled): in this way you add a further degree of protection to the receiver.

4.1.3 HIde - HIDDEN KEY (only with biroL coding)

It is possible to enable or disable the hidden button of the transmitters. This button allows you to enter the sequential learning/

delete the remote control.

4.1.5 Input - WIRED INPUTS PARAMETERS

It allows to associate to each wired input an output function.

There are 4 different functions:

- 0: Dead Man;

- 1: Step by step;

- 2: Timed;

- 3: Timed + Delay.

To change the parameter please follow the procedure below:

MENU DESCRIPTION

SELECTABLE

VALUES

min-max

DEFAULT UNIT

rtIme

PARAMETERS FOR OUTPUTS

Sub-menu where you can:

- set the activation time of the output with the Timed function or

Timed+Delay function (LiFE);

- set the delay time for the Timed+Delay function (dLy).

LiFE

1-65535

dLy

0-255

LiFE

dLy

def RESET OF THE PARAMETERS

It restores the receiver to default settings.

9/20

6-1620020 rev.0 27/10/2015

ITA ENG FRA ESP DEU POR

ENG

4.1.6 rtime - OUTPUT PARAMETERS

In this sub-menu, for each relay (r01, r02, r03 o r04) it is possible to change the activation duration (LIFE) and the output delay

time (dLy).

To change the parameters, please follow the procedure below:

4.1.7 def - PARAMETERS RESET

By accessing the item def it is possible to restore the default values of the receiver. This reset does not delete the password and the

transmitters registered in the memory except for the parameters of the default transmitter.

In order to proceed with the reset, move to the item def and then con!rm with a long pressure of the MENU button. Keep pressed

until the display shows the value 0, then release the button. Keep pressed again the MENU button: a countdown starts d80, d79, …,

d01, d00. Once the countdown ends, the reset has successfully been performed, and the display shows .

4.2 Modif - TRANSMITTER PERSONALIZATION

By accessing the item ModiF it is possible to customize the transmitters in the memory.

In order to proceed with the change, move to the item Modif, and then con!rm with a long pressure of the MENU button.

Keep pressed until the display shows the !rst position occupied by a transmitter (e.g. p0.0.0), then release the button. The positions

of the memory occupied by a transmitter are indicated by the presence of a point between the digits (for example P0.0.1).

The default transmitter, used during the learning (see section 3.1), is indicated in the memory as Pdef: it is possible to change its

characteristics as for any other remote control, but it cannot be moved/deleted/enabled.

Pdef is located before the position P000.

Use the UP (+) and DOWN (-) buttons to choose the desired transmitter, then con!rm with a long pressure of the MENU button. To

know the location of a speci!c transmitter, use the function SEE (see section 4.4) of the receiver.

Once the transmitter is con!rmed, a sub-menu opens, where it is possible:

UWLPH

Go to the menu item rtime.

The display shows:

Press and hold the MENU button

until the display shows:

or or or

U

Select the output with the UP (+) and DOWN (-) buttons of the receiver.

The display shows:

Press and hold the MENU button until the display shows:

/,IH

U

U

U

U

U

U

U

G/\

Select the desired parameter with the UP (+) and DOWN (-) buttons.

Press and hold the MENU button until the parameter blinks.

Set the desired value using the UP (+) and DOWN (-) buttons.

Con!rm the change with a long pressure of the MENU button

GGRQ

10/20 6-1620020 rev.0 27/10/2015

ITA ENG FRA ESP DEU POR

ENG

MENU DESCRIPTION

SELECTABLE

VALUES

min-max

DEFAULT UNIT

deL REMOVAL OF THE TRANSMITTER

It allows the removal of the single transmitter.

enab ENABLING OF THE TRANSMITTER

It allows to enable or disable the transmitter. ON-OFF ON

move

MOVING OF THE TRANSMITTER

It allows to move the location where the transmitter has been

registered in the memory.

000-999

btn

BUTTONS PERSONALISATION

By selecting the button (b01, b02, ..., b15, b16) it is possible:

• to associate the output function (FUnCT):

- F00: Dead Man;

- F01: Step by Step;

- F02: Timed;

- F03: Timed+delay.

• to associate output channels (CH01, CH02, CH03, CH04).

4.2.1 deL - REMOVAL OF THE TRANSMITTER

By accessing the item deL it is possible to delete the single transmitter from the receiver.

In order to proceed with the removal, move to the item deL and then con!rm by a long pressure of the MENU button. Keep pressed

until the display shows the value 0, then release the button. Hold again the MENU button: a countdown starts d20, d19, …, d1, d0.

Once the countdown ends, the reset has successfully been performed, and the display shows .

4.2.2 enAb - ENABLING OF THE TRANSMITTER

It allows to enable or disable the single transmitter. This function serves to disable the transmitter during a period of time, without

removing it from the memory and thus maintaining the con!gured characteristics.

4.2.3 Move - MOVING OF THE TRANSMITTER

It allows to move the position of the transmitter in the receiver’s memory.

In order to proceed with the change, move to the item Move, then con!rm with a long pressure of the MENU button. Keep pressed

until the display shows the !rst free position (e.g. p000), then release the button. The positions of the memory occupied by a

transmitter are indicated by the presence of a point between the digits (for example P0.0.1).

Use the UP (+) and DOWN (-) buttons to select the desired position and con!rm by a long pressure of the MENU button. Keep

pressed until the display shows the value Moved, then release the button.

4.2.4 btn - BUTTONS PERSONALISATION

It allows to personalize the transmitter’s single button. It is possible to associate the function and the output channels (even more

than 1) to each transmitter’s button.

Please follow the procedure below to proceed with the changes:

&/HDU

Select the button to modify with the UP (+) and DOWN (-) buttons of the receiver.

The display shows:

)

Press and hold the MENU button until the display shows:

If the key was already saved, the display can show the function previously

assigned:

Select the desired function with the UP (+) and DOWN (-) buttons.

)

)

)

E

E

Autres manuels pour B.RO X40 DISPLAY

Table des matières

Autres manuels Allmatic Récepteur

Allmatic

Allmatic B.RO MINI 1CH Manuel utilisateur

Allmatic

Allmatic B.RO MINI 1CH Manuel utilisateur

Allmatic

Allmatic B.RO MINI 1CH Manuel utilisateur

Allmatic

Allmatic B.RO X40 DISPLAY Manuel utilisateur

Allmatic

Allmatic TCOO PLUS Mode d’emploi

Allmatic

Allmatic B.RO 44 Series Manuel utilisateur

Manuels Récepteur populaires d'autres marques

Garmin

Garmin GA 23 Manuel utilisateur

Aiphone

Aiphone PS-12F Manuel utilisateur

IMES

IMES TCS-01CA-PMI Manuel utilisateur

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuel

AMIMON

AMIMON AMN12310 WHDI Manuel utilisateur

Dual

Dual DMCPA79BT Mode d'emploi

Sound Associates

Sound Associates SA652P Manuel utilisateur

Sherwood

Sherwood NewCastle R-772 Manuel utilisateur

Audio

Audio A10-RX Series Manuel utilisateur

AllSee

AllSee PushShare PSRV1.1 Manuel utilisateur

DEMAG

DEMAG DRC-DR D2 Manuel utilisateur

Teleco

Teleco TVRCL868A02 Manuel utilisateur

Bosch

Bosch RF3222E Manuel utilisateur

Kramer

Kramer 631R Manuel utilisateur

Xpress

Xpress xmc10 Manuel utilisateur

JVC

JVC KD-MR1BTS Manuel utilisateur

Omega Engineering

Omega Engineering UWTC-REC3 Manuel utilisateur

e-survey

e-survey E300 Pro Manuel utilisateur