allen AW16-B Mode d’emploi
SAFETY &
OPERATIONS MANUAL
Manual Part #: 068517 | Revision: B
Language: English | Original Instructions
WHEEL BUGGIES
AW16-B
068521
Page 2
SAFETY & OPERATIONS MANUAL
Wheel Buggy
Copyright © 2021 Allen Engineering Corporation
All rights reserved
All information, specifications, and illustrations in this manual are subject to change without notice and are based on the latest
information at the time of publication. No part of this manual may be reproduced or transmitted in any form or by any means,
electronics or mechanical, for any purpose, without the express written permission of Allen Engineering Corporation (AEC). AEC
assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual.
Allen Products are covered under one or more of the following patent numbers:
10,100,537; 9,068,301; 9,068,300; 8,360,680; 7,690,864; 7,114,876B1; 6,857,815B2; 6,582,153
With other Patents Pending.
Printed in U.S.A.
This manual, or a copy of it, must be kept with the machine at all times.
There is a manual storage container located on the machine for your convenience.
This manual covers the Trowel Parts listed below
Part No.Part No. DescriptionDescription
073000 AW16-B, All Electric Wheel Buggy, Poly-Bucket, Foam Filled Tires073000 AW16-B, All Electric Wheel Buggy, Poly-Bucket, Foam Filled Tires
068521 Page 3
GENERAL
INFORMATION
Allen Engineering Corporation (“Allen”) warrants its products to be free of defects in material or
workmanship for:
TWO YEARS FROM END USER’S DATE OF PURCHASE
Warranty period begins on the date of purchase by the End User of the product. All warranty is based on
the following limited warranty terms and conditions, including the disclaimer of implied warranties and
consequential damages.
1. Allen’s obligation and liability under this warranty is limited to repairing or replacing parts if, after Allen’s inspection, there is
determined to be a defect in material or workmanship. Allen reserves the choice to repair or replace.
2. If Allen chooses to replace the part, it will be at no cost to the customer and will be made available to the Allen Distributor, Dealer,
or Rental Center from whom the End User purchased the product.
3. Replacement or repair parts, installed in the product, are warranted only for the remainder of warranty period of the product as
though they were the original parts.
4. Allen does not warranty engines or batteries. Engine warranty claims should be made directly to an authorized factory service center
for the particular engine manufacturer. Batteries are not warranted due to unknown treatment during transport, etc, and any battery
claims should be directed to the battery manufacturer.
5. Allen’s warranty does not cover the normal maintenance of products or its components (such as engine tuneups and oil & lter
changes). The warranty also does not cover normal wear and tear items (such as belts and consumables).
6. Allen’s warranty will be void if it is determined that the defect resulted from operator abuse, failure to perform normal maintenance
on the product, modication to product, alterations or repairs made to the product without the written approval of Allen. Allen
specically excludes from warranty any damage to any trowels resulting from an impact to the rotors.
7. Impact damage to gear boxes is not covered under the Allen warranty and is deemed customer abuse.
8. Allen will pay shop labor on warranty items at the Allen Shop Labor Rate in existence on the date of the warranty claim.An Allen labor
chart will determine the time allowed to complete a repair and will govern the shop labor hours that will be allowed.
9. Allen will pay freight on warranty replacement parts at worldwide standard ground rates. No warranty replacement parts will be
shipped air freight at the expense of Allen. Allen only pays outbound freight charges when sending warranty replacement parts to
the customer via ground service. Allen does not pay any inbound freight. However, if Allen determines this to be a warranted item,
only then will Allen reimburse the customer for inbound freight at standard ground rates.
10. ALLEN ENGINEERING CORPORATION’S WARRANTY POLICY WILL NOT COVER THE FOLLOWING: TAXES; SHOP SUPPLIES;
ENVIRONMENTAL SURCHARGES; AIR FREIGHT; TRAVEL TIME; LOSS OF TIME; INCONVENIENCE; LOSS OF RENTAL REVENUE; RENTAL
COSTS OF EQUIPMENT USED TO REPLACE THE PRODUCT BEING REPAIRED; LOSS OF USE OF THE PRODUCT; COMMERCIAL LOSS;
OR ANY OTHER CHARGES WHATSOEVER OR ANY LIABILITIES FOR DIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE OR DELAY.
11. ALLEN ENGINEERING CORPORATION MAKES NO OTHER WARRANTY, EXPRESSED OR IMPLIED. THIS LIMITED WARRANTY IS IN
LIEU OF THE WARRANTY OF MERCHANTABILITY AND FITNESS. THERE ARE NO OTHER WARRANTIES THAT EXTEND BEYOND THE
DESCRIPTION ON THIS DOCUMENT.
12. No Allen employee or representative is authorized to change this warranty in any way or grant any other warranty unless such
change is made in writing and signed by an ofcer of Allen Engineering Corporation.
Limited Warranty
GENERAL
INFORMATION
068521
Page 4
Table of Contents
Sect Title Page
- General Information
Limited Warranty .....................................................................................................................................3
Information Contained in This Manual......................................................................................................5
Sound & Vibration Testing .......................................................................................................................6
Dealer Information / Ordering Parts .........................................................................................................7
Model Number / Serial Identification, Unit Identification...........................................................................8
Technical Specifications ..........................................................................................................................9
1.0 Safety .....................................................................................................................................................10
Federal / State Warning Regulations........................................................................................................11
Manual Tag Safety Detail.........................................................................................................................12
Hazard Symbols.......................................................................................................................................13
General Safety.........................................................................................................................................14
Lifting Safety ...........................................................................................................................................15
Transportation Safety ..............................................................................................................................16
2.0 Operation ...............................................................................................................................................18
Introduction .............................................................................................................................................19
Operating Instructions..............................................................................................................................20
Charging the Unit.....................................................................................................................................26
3.0 Service ...................................................................................................................................................27
Cleaning Procedure .................................................................................................................................28
4.0 Accessories............................................................................................................................................29
Accessories / Manual Revision Detail.......................................................................................................30
Parts Manual ...........................................................................................................................................31
068521 Page 5
GENERAL
INFORMATION
This manual provides information and procedures to safely operate and maintain the Allen Machine.
For your own safety and protection from personal injury, carefully read, understand, and observe the safety instructions
described in this manual. Keep this manual or a copy of it with the machine at all times.
Always operate this machine in accordance with the instructions described in this manual. A well maintained piece of
equipment will provide many years of trouble free operation.
This manual is divided into the following sections:
Complete any warranty requirements as specified by the engine manufacturer in their instructions found inside the
manual box located on the back of the riding trowel operator’s seat.
Your engine and clutch is not manufactured by Allen Engineering Corporation, Inc, and therefore is not covered under
Allen Engineering Corporation, Inc warranty.
Your engine manufacturer should be contacted if you wish to purchase a parts manual or a repair manual for your
engine.
Refer to enclosed owners engine manual for complete OEM instructions. See your battery manufacturer for battery
warranty.
SECTION 1
SAFETY
SECTION 2
ASSEMBLY
SECTION 3
SERVICE
SECTION 4
ACCESSORIES
Information Contained
in this Manual
GENERAL
INFORMATION
068521
Page 6
Sound Pressure Level Information:
Sound pressure is “A” weighted . Measured at the operators ear position while the ride-on trowel is operating at
full throttle on concrete in a manner most often experienced in “normal ” circumstances. Sound pressure may vary
depending upon the condition of the concrete. Hearing protection is always recommended.
Vibration Level Information:
The vibration level indicated is the maximum RMS (Root Mean Square) velocity value obtained at the handle grip while
operating the ride-on trowel on curing concrete in a manner most often experienced in “normal ” circumstances.
Values were obtained from all three axes of motion. The values shown represent the maximum RMS value from these
measurements.
PENDING INFORMATION
Summary Data Of Sound And Vibration Testing
Operator Ear SPL Seat Vibration Average Left Hand
Vibration Average
Right Hand
Vibration Average
- dB (A) - m/sec² - m/sec² - m/sec²
This information was acquired from sound and vibration analysis tests conducted at Allen Engineering
Corporation test facilities.
Sound & Vibration Testing
068521 Page 7
GENERAL
INFORMATION
Dealer Information /
Ordering Parts
Your Dealer has Allen Engineering Corporation trained mechanics and original Allen replacement parts. Always con-
tact the Allen Dealer who sold you this machine for Allen Certified repairs and replacement parts.
Place Allen Dealer information below for future reference.
Dealer Name:
Dealer Phone #:
( ) - -
Address:
City / State / Zip:
Salesman:
Salesman Phone #:
Additional Comments:
The “PARTS & DECALS MANUAL” contain illustrated parts lists for help in ordering replacement parts for your
machine. Follow the instructions below when ordering parts to ensure prompt and accurate delivery:
1. All orders for service parts - include the serial number for the machine. Shipment will be delayed if this information
is not available.
2. Include correct description and part number from the “PARTS & DECALS MANUAL”
3. Specify exact shipping instructions, including the preferred routing and complete destination address.
4. DO NOT return parts to AEC without receiving written authorization from AEC. All authorized returns must be
shipped pre-paid.
5. When placing an order, please contact the AEC dealer nearest you.
ALL INFORMATION, SPECIFICATIONS, AND ILLUSTRATIONS IN THIS MANUAL
ARE SUBJECT TO CHANGE WITHOUT NOTICE AND ARE BASED ON THE
LATEST INFORMATION AT THE TIME OF PUBLICATION.
GENERAL
INFORMATION
068521
Page 8
Model Number / Serial Number
Unit Identication
Manufacturer’s Codes:
When ordering parts or requesting service information, you will always be asked to specify the
model and serial numbers of the machine. The legends below specically denes each signicant
character or group of characters of the Model Number and Serial Number codes.
Serial Number:
The serial number found on the identification plate is a ten digit format. The model number iden-
tifies your machine and will ensure that you receive the correct replacement parts.
Unit Identification Plate Location:
An identification plate listing the model number and the
serial number is attached to each unit and is located on the
inside behind the front door of the unit. This plate should
not be removed at any time.
Please record the information found on this plate below so
it will be available should the identification plate become
lost or damaged. When ordering parts or requesting service
information, you will always be asked to specify the model
and serial numbers of the machine.
Model Number:
Serial Number:
Date Purchased:
Purchased From:
Model Number
AW 16 - B
16ft3- Bucket Capacity
Allen Wheel
Serial Number Example
BW16 01 20 01
Model
Sequence Number
Month
Year
Battery (Full Electric)
068521 Page 9
GENERAL
INFORMATION
Technical Specications
98 1/4" 44"
58"
Dimension with Accessories
Measurements in this manual are in standard units
Machine Features for AW16-B:
•No Emissions
• Ingress Rating.............................................................................IP67
• Run Time............................................................................ 9+ hours
• Charge Time ..........................................................................6 hours
• Motor.............................................................Brushless AC Induction
• Charger Power Input ..................100VAC @ 60Hz - 240VAC @ 50 Hz
• DC Output........................................................................1050 Watts
• Battery......................................................................Lithium-Ion 14S
• Weight (unloaded)...............................................................1,300 lbs
• Dimensions (L x W x H)......................................98-1/4” x 44” x 58”
• Battery Voltage ............................................................................58v
• Wheelbase...................................................................................40”
•Payload...............................................................................2,500 lbs
•Bucket Capacity........................................................................ 16 ft3
•Lift Cylinder ....................................................................2” Diameter
•Dump/Return Speed (Empty)............................................. 5 Seconds
•Top Speed
- Forward ............................................................................ 6 MPH
- Reverse..............................................................................- MPH
SECTION 1
SAFETY
068521
Page 10
SECTION 1
SAFETY
Autres manuels pour AW16-B
1
Table des matières
Autres manuels allen Matériel de construction
allen
allen AT-16 Guide d'application
allen
allen TRTP150B Guide d'application
allen
allen WB2434 Manuel utilisateur
allen
allen WB1224 Manuel utilisateur
allen
allen TRTP75 Mode d’emploi
allen
allen SE12 Guide d'application
allen
allen AT14F Guide d'application
allen
allen RS844 Guide d'application
allen
allen WB1824 Manuel utilisateur
allen
allen BDF4836 Manuel utilisateur
