Alibi Security ALI-QVR5016H Manuel utilisateur
1www.AlibiSecurity.com
About the Alibi Cong Tool
The Alibi Cong Tool is a PC-based network utility for discovery of Alibi compatible devices on a IP network. It provides an easy
way to activate Alibi devices, congure camera and recorder network conguration settings, and set device passwords. It can be
installed on a Microsoft® Windows® operating system that has access to the IP network where your Alibi devices are installed.
Step 1. Install the Alibi Config Tool software
1. Download the Alibi Cong Tool from the AlibiSecurity.com website. At the time when this document was published, the le is
named: alibi-cong-tool.zip and is about 80MB.
2. Un-zip the le on a computer with Microsoft Windows (Windows 7 or newer) that is connected to the LAN where your Alibi camera is
connected.
3. Run the le contained in the zip le: Alibi Cong Tool.exe. Follow the on-screen instructions to install the le.
4. Open the Alibi Cong Tool application. When the application opens, it automatically “discovers” and lists all Alibi compatible devices on
the LAN. See below.
Notice: In the screen above, the tool discovered devices with IP addresses of 192.168.3.xxx. It will also list other Alibi compatible
devices on the LAN, and devices with the address 192.168.1.64 (an inactive Alibi device).
Step 2. “Activate” inactive Alibi camera
When an Alibi camera is rst installed, or reset to its factory conguration, it must be “Activated” before it can be used. In the Alibi
Conguration Tool, “Inactive” devices have a Security status of Inactive, and an IPv4 address of 192.168.1.64. A device is “Activated” when
a password is assigned to the admin username of the device.
In the example below, an ALI-NS2112VR camera is activated and congured for its network.
1. Scan through the list of devices the Alibi Cong Tool discovered for the Inactive device you want to activate (see below). Click on the
device in the list to highlight it, and then click the select box to check it. See below.
Alibi Security IP cameras are usually installed on a network in either of two ways:
• Connected to the internal switch of a network video recorder (NVR): In this conguration, Ethernet cables
connect the camera directly to an NVR back panel. The NVR automatically “Activates” the camera and congures the
camera’s network parameters to establish a communications link between them. In the diagram below, IP Cam A is
connected to the NVR which activates the camera and set up its network parameters.
• Connected to the network router: In this conguration, Ethernet drop cables connect the camera to a network switch
(router). The network utility, Alibi Cong Tool, is used to “Activate” the camera and congure the camera’s network
parameters so that the camera can communicate across the network. In the diagram below, IP Cam B and IP Cam C are
connected to the router, and are activated with the Alibi Cong Tool on Computer B.
Computer A
Computer B with
Alibi Cong Tool
Smartphone with
Alibi Witness 2.0 app
IP Cam C
IP Cam B
Network VIdeo Recorder (NVR)
Internet
Ethernet
Firewall
IP Cam A
In the diagram above, NOTE that:
• Computer A cannot directly access any devices within the router rewall (with a browser) unless the device activated and setup with
network parameters compatible with the router, and the router is congured for port forwarded to the device.
• Computer B with Alibi Cong Tool is used to activate Alibi cameras connected directly to the router (IP Cam B, IP Cam C) and
setup their network parameters. After Alibi devices on the router are activated and congured for the network, Computer B can
access each device using IE.
• The Smartphone (Android or iOS) with Alibi Witness app can access the NVR with IP Cam A through the Guarding Vision
Cloud service without port forwarding the router. However, the router must be congured for port forwarded to IP Cam B and IP
Cam C to access them.
This guide provides a generic instructions for activating and setting up the network parameters for new Alibi cameras Connected
to the network router using the Alibi Cong Tool. The examples shown herein activate an Alibi camera and congure its
network settings. Currently, the procedure is identical for all new Alibi IP cameras.
ALIBI™ IP Camera Network Setup Guide
ALI-IP_Cam-Ntwk_Setup_CQ
180605
2www.AlibiSecurity.com © 2018 Observint Technologies. All rights reserved.
Activate
2. Click the Activate button. In the Activate window, create a password for the admin (administrator) username:
a. In the Activate window, enter an a password for admin in the New Password eld. Use a combination of uppercase, lowercase
alphabetic characters and numbers to create a “Strong” password. The rating is shown beneath the eld. See above.
b. Enter the admin password again in the Conrm eld, and then click Activate. In the screen below, notice that the device
Security status shows “Active”. Record your admin password for reference later.
CAUTION
If you lose your admin (administrator) password, you cannot congure the device or restore it to its factory settings. To reset your
password, call your support organization for specic instructions.
Notice that although the device is now activated, it retained the default IP address, 192.168.1.64.
Step 3. Modify Network Parameters
1. In the list of devices discovered, click on the device you want to change the network settings for, click the select box to check it, and
then click the Modify Network Parameters button. See below.
Modify Network Parameters
2. In the popup window, edit the current network parameters, and then enter the admin user password in the eld at the bottom.
a. Enable DHCP: You can select Enable DHCP to acquire compatible network settings from a DHCP server installed on the LAN.
However, these settings can be changed by the DHCP server. Since it is recommended to use an unchanging IP address, you can
use DHCP to acquire compatible network settings, and then uncheck Enable DHCP and save that conguration to retain the
new network parameters.
b. In the example below, the IPv4 address was changed to 192.168.3.100, and the IPv4 Gateway was changed to 192.168.3.1. These
settings were determined to be compatible with the network router and other devices that share the same router.
3. Click OK to save your settings. The parameter change(s) will be shown device’s network parameters (see below).
3www.AlibiSecurity.com © 2018 Observint Technologies. All rights reserved.
Step 4. Login to the camera
Microsoft® IE is used to access your camera remotely. IE must run as an Administrator to use all features available through a remote login to
the camera.
Setting MS Internet Explorer to run as an Administrator
Window 7: To run IE as an Administrator:
1. Find or create an IE icon on your computer desktop.
2. Hold down the shift key, and then right-click on the IE icon.
MS Internet
Explorer icon
Run as administrator
3. Click Run as administratorin the pop-up menu.
Window 10:
To run IE as an Administrator:
1. Find IE in the start menu. Usually this is found in the Windows Accessories group.
2. Pin the entry to Start.
3. Right click on the Internet Explorer tile, and then select More | Run as administrator.
Run as
administrator
To login to the camera from a computer on the same LAN:
1. Open your IE browser and enter the IP address of the camera in the URL eld. In the example below, the IP address of the camera is
192.168.3.100.
2. In the login window, enter admin for the User Name and the password you created in the Password eld, then click Login.
3. If this is the rst time you are logging into a camera, you may see the message in the following screen. If this appears, follow the sub-
steps below.
a. Click on the message to install the plugin.
4www.AlibiSecurity.com © 2018 Observint Technologies. All rights reserved.
b. In the message bar at the bottom of the screen, click Run. Follow the on-screen instructions to install WebComponents. When
the following screen opens, click Finish.
The Live View screen with the camera video image should appear.
Capture, Record, Zoom icons
Screen select tabs Logout button
Live View image
For more information about the IE browser interface to your camera, go to the AlibiSecurity.com for the latest Alibi IP Camera Firmware
User Manual for your camera.
NOTE Most Alibi IP cameras have a Reset button for returning the camera conguration to its factory settings. Refer to the Installation Guide provided
with the camera for more information.
Ce manuel convient aux modèles suivants
5
Autres manuels Alibi Security Caméra de sécurité
