Algoma Net Soft Comfort Fiche technique
SOFT COMFORT SWING CHAIR AND FRAME
ASSEMBLY INSTRUCTIONS AND PARTS LIST
Please read and save these instructions for future reference. Please check and make sure all parts are contained
in the carton before proceeding with assembly.
PARTS LIST:
2 U-Shaped Header Bars (#1)
4 Upper Pole with Hole Punched (#2)
4 Lower Pole without Hole (#3)
2 U-Shaped Based rail (#4)
2 Cross Brace (#5)
1 Hardware Bag
Hardware bag contains the following parts:
4 Bolts 1-3/4” x 3/8” P6042
4 Locknuts 3/8” x 24 P6048
4 S-Hooks P6049
4 Push on Nuts P6050
AS AN ADDED BONUS, ALGOMA HAS SUPPLIED
A WATER BOTTLE HOLDER WHICH YOU CAN
HANG FROM EITHER BRACE (NO. 5)
Assembling the Frame (See Diagram 1)
1. Insert the plain end of the four upper poles (2) into the tapered ends of the four lower poles (3). Make sure the
holes of the upper poles face to the outside as shown in the diagram. Make sure the spring pins snap completely
into place.
2. Insert the plain end from the assembled poles above into the four tapered ends of the U-shaped base rails (4).
Make sure the spring pins snap completely into place.
3. You may now put the U-shaped header bars (1) over the tapered end of the upper poles with hole on both sides.
Again, remember to have the holes in the upper poles facing to the outside. Make sure the spring pins snap
completely into place.
4. Take the four bolts from the hardware bag and the two cross braces (5) and assemble to the upper poles (2).
Insert the bolt from the inside of frame through the tubing first and then through the brace (5). The brace fits to
the outside of the tubing.
5. Secure the bolts by screwing on the four locknuts. Make sure the locknuts are tightly secured. You will need two
9/16” wrenches to tighten the nuts.
6. Place the four S-Hooks in the holes provided. There are two holes in the U-shaped headers (1) and two holes in
the braces (5). Insert the longer straight part of the S-Hook through the hole. See diagram 2. Secure by
pushing on the four push on nuts to the bottom of the S-Hooks.
WARNING!
Before attaching the swing chair to the frame, make sure all tapered tubular parts fit completely inside the
adjoining tubing piece. Make sure the spring pins snap completely into place.
(over)
Attaching the Chair to the Frame
Assemble the chair to the frame by putting the holes in the J-Hooks attached to the chair, over the S-Hooks. Make sure
you have the two J-Hooks attached at the same height.
Please Note:
There are two heights at which you can hang the chair from. You must determine which height is best for your
maximum enjoyment. The heights are easily interchangeable by simply removing the J-Hooks and switching
them to the other height.
Your swing is ready for use. Relax and enjoy it. For a longer life of your swing chair, take the chair seat inside when not
in use for extended periods of time.
Warning:
This product was designed for your leisure and comfort. It was not intended to be used as a swing set or to be
abused by swinging severely back and forth. Any drastic force could cause the frame to tip and cause injury.
Occasionally check the fit of all the parts, especially after moving the frame from one location to another. All
tubing pieces should fit totally over the swagged, tapered pieces.
ADULT SUPERVISION RECOMMENDED DURING CHILD USE
For Customer Service, Please Contact:
THE ALGOMA NET COMPANY, Div. of Gleason Corp.
1525 Mueller Street
Algoma, WI 54201
Phone: (920) 487-5577
Fax: (920) 487-2852
Web: www.algomanet.com
10/08
Table des matières
Autres manuels Algoma Net Hamac
Manuels Hamac populaires d'autres marques
Costway
Costway Patiojoy NP10175 Manuel utilisateur
Astonica
Astonica 50104226 Manuel utilisateur
Texsport
Texsport La Paz 14258 Manuel utilisateur
Hatteras Hammocks
Hatteras Hammocks L-EKD Manuel utilisateur
Coopers of Stortford
Coopers of Stortford 10568 Manuel utilisateur
Texsport
Texsport Daydreamer 14265 Manuel utilisateur
