Algo 8138 Manuel utilisateur
8138 SIP Multicolor Strobe Light
8138 SIP Multicolor Strobe Light
User Guide
Document 90-00102C
11/27/2019
Page 1
lgo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8138 SIP Multicolor Strobe Light
Table of Contents
IMPORTANT SAFETY INFORMATION...................................................................................................... 4
O ER IEW.................................................................................................................................................. 7
Introduction........................................................................................................................................... 7
Key Features......................................................................................................................................... 7
Terminal Block Reset........................................................................................................................... 8
SETUP AND INSTALLATION..................................................................................................................... 9
Getting Started - Quick Install & Test..................................................................................................9
Ceiling and Wall Mounting................................................................................................................. 10
Programming and Configuration....................................................................................................... 10
Inputs/Outputs.................................................................................................................................... 11
FEATURES................................................................................................................................................ 12
SIP Paging: One 8138......................................................................................................................... 12
SIP Ring Event.................................................................................................................................... 12
Multicast Overview............................................................................................................................. 12
SIP Paging: Multiple 8138 (Using Multicast).....................................................................................13
SIP Paging: Multiple Strobe (Using Individual SIP extensions)......................................................13
SIP Activated Notification Alerts....................................................................................................... 13
TLS for SIP Signaling and Provisioning...........................................................................................14
WEB INTERFACE BASIC SETTINGS......................................................................................................18
Web Interface Login............................................................................................................................18
Status................................................................................................................................................... 19
Basic Settings Tab – SIP.................................................................................................................... 19
Basic Settings Tab – Features........................................................................................................... 21
Basic Settings Tab – Strobe.............................................................................................................. 22
Basic Settings Tab – Multicast.......................................................................................................... 22
Basic Settings Tab – Multicast (Master Settings)............................................................................24
Basic Settings Tab – Multicast (Slave Settings)..............................................................................26
WEB INTERFACE ADDITIONAL FEATURES..........................................................................................28
Additional Features Tab – Input/Output............................................................................................28
Additional Features Tab – Emergency Alerts...................................................................................31
Additional Features Tab – More Page Extensions...........................................................................33
Additional Features Tab – More Ring Extensions...........................................................................34
WEB INTERFACE AD ANCED SETTINGS.............................................................................................35
Advanced Settings Tab – Network....................................................................................................35
Advanced Settings Tab – Admin....................................................................................................... 37
Advanced Settings Tab – Time.......................................................................................................... 40
Advanced Settings Tab – Provisioning.............................................................................................41
Advanced Settings Tab – Advanced Audio......................................................................................43
Advanced Settings Tab – Advanced SIP..........................................................................................44
Advanced Settings Tab – Advanced Multicast.................................................................................47
WEB INTERFACE SYSTEM..................................................................................................................... 48
System Tab – Maintenance................................................................................................................ 48
System Tab – Firmware...................................................................................................................... 49
Advanced Settings Tab – File Manager............................................................................................50
Document 90-00102C
11/27/2019
Page 2
lgo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8138 SIP Multicolor Strobe Light
System Tab – System Log................................................................................................................. 51
WIRING CONNECTIONS.......................................................................................................................... 51
Network Connection........................................................................................................................... 51
Connecting Input Devices.................................................................................................................. 51
SPECIFICATIONS..................................................................................................................................... 52
FCC COMPLIANCE STATEMENT............................................................................................................ 53
Document 90-00102C
11/27/2019
Page 3
lgo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8138 SIP Multicolor Strobe Light
Important Safety Information
Important Safety Information
This product is powered by a certified limited power source (LPS), Power over Ethernet
(PoE); through C T5 or C T6 connection wiring to an IEEE 802.3at PoE+ or 802.3af
compliant network PoE switch. The product is intended for installation indoors. ll wiring
connections to the product must be in the same building. If the product is installed beyond
the building perimeter or used in an inter-building application, the wiring connections must
be protected against overvoltage/transient. lgo recommends that this product is installed
by a qualified electrician.
If you are unable to understand the English language safety information then please
contact lgo by email for assistance before attempting an installation
Consignes de Sécurité Importantes
Ce produit est alimenté par une source d’alimentation limitée certifiée (alimentation par
Ethernet); des câbles de catégorie 5 et 6 joignent un commutateur réseau à alimentation
par Ethernet homologué IEEE 802.3at PoE+ or 802.3af. Le produit est conçu pour être
installé à l’intérieur. Tout le câblage rattaché au produit doit se trouver dans le même
édifice. Si le produit est installé au-delà du périmètre de l’édifice ou utilisé pour plusieurs
édifices, le câblage doit être protégé des surtensions transitoires. lgo recommande qu’un
électricien qualifié se charge de l’installation de ce produit.
Si vous ne pouvez comprendre les consignes de sécurité en anglais, veuillez
communiquer avec lgo par courriel avant d’entreprendre l’installation au
Información de Seguridad Importante
Este producto funciona con una fuente de alimentación limitada (Limited Power Source,
LPS) certificada, limentación a través de Ethernet (Power over Ethernet, PoE); mediante
un cable de conexión C T5 o C T6 a un conmutador de red con PoE en cumplimiento
con IEEE 802.3at PoE+ or 802.3af. El producto se debe instalar en lugares cerrados.
Todas las conexiones cableadas al producto deben estar en el mismo edificio. Si el
producto se instala fuera del perímetro del edificio o se utiliza en una aplicación en varios
edificios, las conexiones cableadas se deben proteger contra sobretensión o corriente
transitoria. lgo recomienda que la instalación de este producto la realice un electricista
calificado.
Si usted no puede comprender la información de seguridad en inglés, comuníquese con
lgo por correo electrónico para obtener asistencia antes de intentar instalarlo:
Document 90-00102C
11/27/2019
Page 4
lgo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8138 SIP Multicolor Strobe Light
Wichtige Sicherheitsinformationen
Dieses Produkt wird durch eine zertifizierte Stromquelle mit begrenzter Leistung (LPS –
Limited Power Source) betrieben. Die Stromversorgung erfolgt über Ethernet (PoE –
Power over Ethernet). Dies geschieht durch eine Cat-5-Verbindung oder eine Cat-6-
Verbindung zu einer IEEE 802.3at PoE+ or 802.3af-konformen Ethernet-Netzwerkweiche.
Das Produkt wurde konzipiert für die Installation innerhalb eines Gebäudes. lle
Kabelverbindungen zum Produkt müssen im selben Gebäude bestehen. Wenn das
Produkt jenseits des Gebäudes oder für mehrere Gebäude genutzt wird, müssen die
Kabelverbindungen vor Überspannung und Spannungssprüngen geschützt werden. lgo
empfiehlt das Produkt von einem qualifizierten Elektriker installieren zu lassenv.
Sollten Sie die englischen Sicherheitsinformationen nicht verstehen, kontaktieren Sie bitte
lgo per Email bevor Sie mit der Installation beginnen, um Unterstützung zu erhalten.
lgo kann unter der folgenden E-Mail- dresse erreicht werden:
安全须知
本产品由认证的受限电源（LPS）以太网供电（PoE）通过 C T5 或C T6 线路联接至
IEEE 802.3at PoE+ or 802.3af 兼容的 PoE 网络交换 供电。本产品适用于室内或建筑物周
边安装。所有联接本产品的线路必须源自同一建筑物。本产品如需用于超出建筑物周边范
围或跨建筑物的安装线路联接部分必须有过压和瞬态保护。 lgo 建议本产品由专业电工
安装。
如果您对理解英文版安全须知有问题安装前请通过电子邮件和 lgo 联
EMERGENCY COMMUNICATION
The 8138 SIP Strobe Light is not intended for fire alarm signaling applications. The 8138
SIP Strobe Light is intended for informative signaling in conjunction with unified
communication systems. The 8138 Strobe Light is suitable for OSH and D
compliance when properly located and configured
DO NOT LOOK DIRECTLY
Do not look directly at the 8138 SIP Strobe Light while operating in close proximity, as
vision may be affected. The LEDs in the 8138 light are classified according to the IEC
62471-2006 standard as “RG-1” for risk group 1. This is defined as “Low risk. No
photobiological hazard under normal behavioral limitations.”
Document 90-00102C
11/27/2019
Page 5
lgo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8138 SIP Multicolor Strobe Light
PHOTO-SENSITI ITY
Photo-sensitivity in some people with epilepsy can trigger seizures from flashing or
flickering lights. It is possible that some flash patterns of the 8138 SIP Strobe Light could
trigger a seizure for some individuals under some conditions. High intensity patterns
should only be selected if necessary for the 8138 to be effective.
WET OR OUTDOOR EN IRONMENTS
The 8138 SIP Strobe Light is intended for indoor or outdoor locations and may be
subjected to spray or weather provided the rear wiring cavity is properly sealed to prevent
water ingress.
Gaskets included with the 8138 SIP Strobe Light may be effective against water ingress
on some, but not all surfaces in which case additional protective measures must be taken
such as a perimeter sealant.
CAT5 or CAT6 connection wiring to an IEEE 802.3at PoE+ or 802.3af compliant
network PoE switch must not leave the building perimeter without adequate
lightning protection.
No wiring connected to the 8138 SIP Strobe Light may leave the building perimeter
without adequate lightning protection.
Document 90-00102C
11/27/2019
Page 6
lgo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8138 SIP Multicolor Strobe Light
Overview
Introduction
The 8138 SIP Strobe Light is a SIP compliant, multicast capable, PoE strobe light.
The flash intensity can be chosen to suit the application and environment. There
are non-flashing patterns for passive gentle notification and aggressive patterns
for maximum conspicuity in busy environments.
The 8138 is typically wall or ceiling mounted. The 360° x 180° visibility, 15
available flash patterns, and 4 color settings makes the 8138 suitable for
notification and alerting of telephone, emergency, safety, and security events.
Light output is equally intense in every direction unless a directional pattern is
chosen.
The 8138 SIP Strobe Light can be activated by:
•SIP Ring
•SIP In-Use (Subscribe Notify)
•Dry contact closure input
•Multicasting
Multiple lgo endpoints in a SIP environment require only one device to register as
a SIP extension. Multicasting capabilities allow the SIP registered strobe to flash
and simultaneously stream multicast events to the other lgo strobes, speakers
and paging adapters in any combination and number of endpoints.
The 8138 SIP Strobe Light is configured using central provisioning features or by
accessing a web interface using browsers such as Google Chrome or Firefox.
Key Features
SIP Extensions
The 8138 connects to an on-premise or hosted communication server in the same
way as a SIP telephone. To register the 8138 with the server requires the following
information:
1. IP address (e.g. 192.168.1.111) or domain name (e.g. myserver.com) of the
SIP Server
2. SIP extension (e.g. 3790)
3. uthentication ID
4. Password
Document 90-00102C
11/27/2019
Page 7
lgo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8138 SIP Multicolor Strobe Light
The 8138 supports two SIP extensions which behave differently – RING and
PAGE. One or both may be used depending on the application. If the RING
extension is called the 8138 will not answer. Instead, it will flash a light pattern until
the inbound call stops ringing. Typically the RING extension is programmed as
part of a hunt group so that it receives a ring signal simultaneously with one or
more devices.
If the P GE extension is called, the 8138 will answer and flash a light pattern until
the call is ended.
Multicasting
llows multiple units to simultaneously flash light patterns. The 8138 can be
configured as a multicast ‘Master’ device to send a multicast stream to other slave
devices. The 8138 can be configured as a multicast ‘Slave’ device to flash a light
pattern when a stream is received from a multicast ‘Master’ device. ny
number/combination of lgo IP speaker, paging adapter, or strobe endpoint can
be configured as multicast ‘Slaves’. This feature provides scalability without
requiring each endpoint Slave to be registered with a SIP extension.
PolycomTM Group Paging
The 8138 supports Polycom Group Paging. The 8138 can be added to a Polycom
Group Page so that voice paging activates a flash pattern while active.
Configuration & Provisioning
Configuration can be done through a web interface control panel or central
provisioning features. Central provisioning allows units to be pre-configured for a
specific server prior to deployment in the field. Configuration files are automatically
downloaded from a server (via TFTP, FTP, HTTP, HTTPS) using DHCP.
Terminal Block Reset
The reset relay terminal on the back can be used to reset the 8138 SIP Strobe
light at time of power up. To return all the settings to the factory default for the
8138, wait until the LED flashes, then connect the reset terminals and hold until
the 8138 LED begins a double flash pattern. Release the reset connection and
allow the unit to complete its boot process.
A reset will set all configuration options to factory default including the
password.
Document 90-00102C
11/27/2019
Page 8
lgo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8138 SIP Multicolor Strobe Light
Setup and Installation
Getting Started - Quick Install & Test
This guide provides important safety information which should be read
thoroughly before permanently installing the strobe.
1. Connect the 8138 SIP Strobe Light to a 802.3af PoE network switch using the RJ45
jack in the back recess of the housing.
2. llow the 8138 SIP Strobe Light time to boot, about 30 seconds. While booting the
Strobe will activate a small dim amber light in the center.
3. If there is no DHCP server found the 8138 SIP Strobe Light will default to the static
IP address 192.168.1.111. Most often however the 8138 will be assigned an IP
address. The IP address may be discovered by downloading the lgo Locator Tool
to find lgo devices on your network: www.algosolutions.com/locator
4. ccess the 8138 web page by entering the IP address into a browser (Chrome,
Firefox etc.) and login using the default password: algo
5. Enter the IP address for the SIP server into the SIP Domain field under the Basic
Settings > SIP tab.
6. Enter the Ring and/or Page SIP extension and credentials. Leave the credentials
blank for either extension if there is no intended use to have both registered.
(Note: The strobe supports multiple Ring, Emergency lert, and Page SIP
extensions. The Page extension auto-answers and flashes a light pattern. The Ring
and Emergency lert extensions will flash a light pattern without answering.)
7. Make a test call from a telephone to the strobe for one or both extensions. The Page
SIP extension should auto-answer and flash the light pattern. The Ring SIP
extension will flash the light pattern without answering the call.
Document 90-00102C
11/27/2019
Page 9
lgo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8138 SIP Multicolor Strobe Light
Ceiling and Wall Mounting
The 8138 SIP Strobe Light can be wall or ceiling mounted. Concealed wiring may enter
from the wall into the wiring cavity. lternatively, surface wiring may enter through a
channel from the bottom edge. The channel is intended for cabling 0.2” or 5mm in
diameter and is intentionally snug to protect against moisture ingress.
The 8138 can be mounted in any orientation but both the bracket and housing identify
TOP. This keeps the bracket wiring chase on the bottom and the RJ45 jack on the top
side.
The mounting plate may be used to mount over flush or surface mounted electrical boxes
or mud rings and fits securely to a 2 gang electrical box (not included) for installation with
wiring conduit.
The 8138 SIP Strobe Light is rated for wet locations however care must be taken to
ensure that water does not enter the wiring cavity. The supplied gaskets or sealant must
be used to protect the wiring cavity in wet environments. In dry indoor environments the
gaskets are not required. If the wall gasket is used with surface wiring, then the gasket
should be attached after placing the cable into the wiring channel.
The 8138 should not be installed beyond a building perimeter without adequately
protecting the building wiring from lightning surge.
Programming and Configuration
fter connecting the 8138 to a network PoE will attempt to obtain an IP address from the
DHCP server. If there is no DHCP server or the attempt was unsuccessful, the 8138 will
default to the static IP address 192.168.1.111.
Document 90-00102C
11/27/2019
Page 10
lgo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
Table des matières
Autres manuels Algo Équipement d'éclairage
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
