Algo 8063 Manuel utilisateur

8063 IP Door Controller

Document 90-00106 Algo Communication Products Ltd (604) 454-3792

2020-09-02 4500 Beedie St Burnaby BC Canada V5J 5L2 [email protected]

Page 1 www.algosolutions.com

8063 IP Door Controller

User Guide

Order Codes

8063 IP Door Controller

Document 90-00106 Algo Communication Products Ltd (604) 454-3792

2020-09-02 4500 Beedie St Burnaby BC Canada V5J 5L2 [email protected]

Page 2 www.algosolutions.com

Table of Contents

Important Safety Information................................................................................................ 3

Overview............................................................................................................................... 5

Introduction.......................................................................................................................................................5

Setup and Installation............................................................................................................ 6

Getting Started - Quick Install & Test.................................................................................................................6

Installation ........................................................................................................................................................7

Programming and Configuration........................................................................................................................7

Wiring Connections ............................................................................................................... 8

Reset .................................................................................................................................................................9

TLS for SIP Signalling and Provisioning ................................................................................. 10

Web Interface Status and Login ........................................................................................... 13

Web Interface login ......................................................................................................................................... 13

Status .............................................................................................................................................................. 14

Web Interface Basic Settings................................................................................................ 15

Basic Settings Tab –Door Control & I/O...........................................................................................................15

Basic Settings Tab –Stand-Alone Mode...........................................................................................................16

Web Interface Advanced Settings ........................................................................................ 19

Advanced Settings Tab - Network....................................................................................................................19

Advanced Settings Tab –Admin.......................................................................................................................21

Advanced Settings Tab –Time ......................................................................................................................... 23

Advanced Settings Tab –Provisioning..............................................................................................................24

Advanced Settings Tab –Advanced Audio .......................................................................................................26

Advanced Settings Tab –Advanced SIP............................................................................................................ 27

Web Interface System.......................................................................................................... 30

System Tab –Maintenance..............................................................................................................................30

System Tab –Firmware....................................................................................................................................31

System Tab –File Manager .............................................................................................................................. 32

System Tab –System Log.................................................................................................................................33

Specifications ...................................................................................................................... 34

FCC Compliance Statement.................................................................................................. 35

8063 IP Door Controller

Document 90-00106 Algo Communication Products Ltd (604) 454-3792

2020-09-02 4500 Beedie St Burnaby BC Canada V5J 5L2 [email protected]

Page 3 www.algosolutions.com

Important Safety Information

This product is powered by a certified limited power source (LPS), Power over Ethernet

(PoE); through CAT5 or CAT6 connection wiring to an IEEE 802.3at PoE+ or 802.3af

compliant network PoE switch. The product is intended for installation indoors. All wiring

connections to the product must be in the same building. If the product is installed

beyond the building perimeter or used in an inter-building application, the wiring

connections must be protected against overvoltage/transient. Algo recommends that this

product is installed by a qualified electrician.

If you are unable to understand the English language safety information then please

contact Algo by email for assistance before attempting an installation

support@algosolutions.com.

Consignes de Sécurité Importantes

Ce produit est alimenté par une source d’alimentation limitée certifiée (alimentation par

Ethernet); des câbles de catégorie 5 et 6 joignent un commutateur réseau à alimentation

par Ethernet homologué IEEE 802.3at PoE+ or 802.3af. Le produit est conçu pour être

installé à l’intérieur. Tout le câblage rattaché au produit doit se trouver dans le même

édifice. Si le produit est installé au-delà du périmètre de l’édifice ou utilisé pour plusieurs

édifices, le câblage doit être protégé des surtensions transitoires. Algo recommande

qu’un électricien qualifié se charge de l’installation de ce produit.

Si vous ne pouvez comprendre les consignes de sécurité en anglais, veuillez

communiquer avec Algo par courriel avant d’entreprendre l’installation au

support@algosolutions.com.

Información de Seguridad Importante

Este producto funciona con una fuente de alimentación limitada (Limited Power Source,

LPS) certificada, Alimentación a través de Ethernet (Power over Ethernet, PoE);

mediante un cable de conexión CAT5 o CAT6 a un conmutador de red con PoE en

cumplimiento con IEEE 802.3at PoE+ or 802.3af. El producto se debe instalar en

lugares cerrados. Todas las conexiones cableadas al producto deben estar en el mismo

edificio. Si el producto se instala fuera del perímetro del edificio o se utiliza en una

aplicación en varios edificios, las conexiones cableadas se deben proteger contra

sobretensión o corriente transitoria. Algo recomienda que la instalación de este producto

la realice un electricista calificado.

Si usted no puede comprender la información de seguridad en inglés, comuníquese con

Algo por correo electrónico para obtener asistencia antes de intentar instalarlo:

support@algosolutions.com.

Wichtige Sicherheitsinformationen

Dieses Produkt wird durch eine zertifizierte Stromquelle mit begrenzter Leistung (LPS –

Limited Power Source) betrieben. Die Stromversorgung erfolgt über Ethernet (PoE –

Power over Ethernet). Dies geschieht durch eine Cat-5-Verbindung oder eine Cat-6-

Verbindung zu einer IEEE 802.3at PoE+ or 802.3af-konformen Ethernet-

8063 IP Door Controller

Document 90-00106 Algo Communication Products Ltd (604) 454-3792

2020-09-02 4500 Beedie St Burnaby BC Canada V5J 5L2 [email protected]

Page 4 www.algosolutions.com

Netzwerkweiche. Das Produkt wurde konzipiert für die Installation innerhalb eines

Gebäudes. Alle Kabelverbindungen zum Produkt müssen im selben Gebäude bestehen.

Wenn das Produkt jenseits des Gebäudes oder für mehrere Gebäude genutzt wird,

müssen die Kabelverbindungen vor Überspannung und Spannungssprüngen geschützt

werden. Algo empfiehlt das Produkt von einem qualifizierten Elektriker installieren zu

lassenv.

Sollten Sie die englischen Sicherheitsinformationen nicht verstehen, kontaktieren Sie

bitte Algo per Email bevor Sie mit der Installation beginnen, um Unterstützung zu

erhalten. Algo kann unter der folgenden E-Mail-Adresse erreicht werden:

support@algosolutions.com.

安全须知

本产品由认证的受限电源（LPS），以太网供电（PoE），通过CAT5 或CAT6 线路联接至

IEEE 802.3at PoE+ or 802.3af 兼容的 PoE 网络交换机供电。本产品适用于室内或建筑物周

边安装。所有联接本产品的线路必须源自同一建筑物。本产品如需用于超出建筑物周边范

围或跨建筑物的安装，线路联接部分必须有过压和瞬态保护。Algo 建议本产品由专业电工

安装。

如果您对理解英文版安全须知有问题，安装前请通过电子邮件和 Algo 联

系，support@algosolutions.com 。

EMERGENCY COMMUNICATION

If used in an emergency communication application, the 8063 should be routinely tested.

SNMP supervision is recommended for assurance of proper operation.

DRY INDOOR LOCATION ONLY

The 8063 IP Door Controller is intended for dry indoor locations only.

CAT5 or CAT6 connection wiring to an IEEE 802.3af compliant network PoE switch

must not leave the building perimeter without adequate lightning protection.

No wiring connected to the 8063 IP Door Controller may leave the building perimeter

without adequate lightning protection.

8063 IP Door Controller

Document 90-00106 Algo Communication Products Ltd (604) 454-3792

2020-09-02 4500 Beedie St Burnaby BC Canada V5J 5L2 [email protected]

Page 5 www.algosolutions.com

Overview

Introduction

The 8063 IP Door Controller provides a dry contact relay closure for the activation of

electronic door strikes. It is typically used in conjunction with an Algo Intercom, including

the 8201, 8036 & 8039, allowing the door wiring to be kept securely inside the building

to prevent unauthorized tampering. In this case, the 8063 does not require a SIP

registration, and communicates only with the Algo Intercom via a secure communication

path over the LAN.

In applications where voice communication is not required, the 8063 can also be used in

standalone mode, and activated directly via a SIP call.

The 8063 also has two relay inputs, and one relay output, allowing it to interface with

external sensors and switches, including magnetic door sensors for tracking the state of

the door to prevent tailgating, or trigger an alarm if the door is held open.

What is Included

•8063 IP Door Controller

•Network Cable

•Wall Mount Bracket

What is not Included

•This Installation Guide (www.algosolutions.com/8063/guide)

•Door Strike

•Door Strike Power Supply

•Intercom (compatible with Algo 8201, 8036 & 8039)

8063 IP Door Controller

Document 90-00106 Algo Communication Products Ltd (604) 454-3792

2020-09-02 4500 Beedie St Burnaby BC Canada V5J 5L2 [email protected]

Page 6 www.algosolutions.com

Setup and Installation

Getting Started - Quick Install & Test

This guide provides important safety information which should be read thoroughly

before permanently installing the adapter.

1. Connect the wiring from your door strike (not included), to the Door Control relay

output terminal block on the 8063 (either “Normally Open” [‘NO’] and “Common” [‘C’],

or “Normally Closed” [‘NC’] and “Common” [‘C’], as appropriate for the door strike).

See the Door Strike Wiring Guide for further information.

2. Connect the 8063 IP Door Controller to a PoE or PoE+ network switch. The blue

lights on the front will remain on until boot up is completed –about 30 seconds.

3. After the blue lights turn off, the IP address may be discovered by downloading the

Algo locator tool to find Algo devices on your network:

www.algosolutions.com/locator

4. Access the 8063 IP Door Controller web page by entering the IP address into a

browser (Chrome, Firefox etc) and login using the default password algo.

5. Use the test buttons in the web interface (Basic Settings > Door Control & I/O) to

confirm the operation of the door strike. Press the Unlock button to test that the door

unlocks, and then press Lock again to confirm that it locks.

After confirming that the hardware installation with the door strike is successful, the 8063

can now be configured for use with either an Algo Intercom (typical application), or in

Stand-Alone Mode (without an Algo Intercom and thus no voice path). Please choose

the appropriate section below based on your application.

For Use with an Algo Intercom (Typical Application)

6. Open the web interface for the Algo Intercom (8201, 8036 or 8039) that is to

communicate with the 8063, using the IP address for this device.

In the web interface for the Intercom, select the Network Door Controller options and

enter the IP address of the 8063 here (and password), so that the Intercom can contact

the 8063 in order to unlock the door. These settings are in Basic Settings > Door

Control in the Intercom web interface –see the documentation of your specific Algo

Intercom model (8201, 8036 or 8039) for further details.

7. Make a call to the Algo Intercom, and press ‘6’ (or appropriate DTMF code as

configured on the Intercom) to unlock the door using the 8063 IP Door Controller.

For Stand-Alone Mode

8. In the 8063 web inteface, enter the IP address or the name for the SIP server into

the SIP Domain field under the Basic Settings > Stand-Alone Mode tab.

9. Enter the credentials (SIP Extension, Authentication ID, and Password) for the SIP

extension.

8063 IP Door Controller

Document 90-00106 Algo Communication Products Ltd (604) 454-3792

2020-09-02 4500 Beedie St Burnaby BC Canada V5J 5L2 [email protected]

Page 7 www.algosolutions.com

Note: The Authentication ID may also be called Username for some SIP servers, and in

some cases may be the same as the SIP extension.

10. Make a call to the controller by dialling the SIP extension of the adapter from a

telephone.

Installation

The 8063 is wall mountable in a horizontal orientation using the supplied bracket.

Example installation on ½” drywall:

Use appropriate drywall anchors for #8 screws, and pre-drill

per anchor manufacturer’s instructions. Insert 4 anchors into

the wall, and then attach bracket to wall anchors using #8

screws. Snap the 8063 into the bracket.

Connect the 8063 to a PoE network switch.

Programming and Configuration

The 8063 IP Door Controller is configurable using the web interface or provisioning

features.

After boot up the blue lights on the front will turn off (except for the power light) and the

adapter will have obtained an IP address. If there is no DHCP server the 8063 IP Door

Controller will default to the static IP address 192.168.1.111.

The IP address may be discovered by downloading the Algo locator tool to find Algo

devices on your network: www.algosolutions.com/locator

Enter the IP address (e.g. 192.168.1.111) into a browser such as Chrome, Firefox, or

Edge. The web interface should be visible and the default password will be algo in lower

case letters.

8063 IP Door Controller

Document 90-00106 Algo Communication Products Ltd (604) 454-3792

2020-09-02 4500 Beedie St Burnaby BC Canada V5J 5L2 [email protected]

Page 8 www.algosolutions.com

Wiring Connections

8063: Front View

8063: Back View

Network Connection (Front)

The 8063 provides a RJ45 jack for network connection. A cable run from the switch can

be terminated to a modular jack with connection by patch cord, or terminated with a

RJ45 plug.

PoE can be used for most applications, whether provided by the network switch or

injector. If using the 24V output to drive a high power door strike directly (as opposed to

just using the relay in conjunction with the door strike’s existing power supply), then

PoE+ may be used to allow more power. See the Specifications section for details on

the current limits in each case.

There are two lights on the Ethernet jack:

Green light: On when Ethernet is working, flickers off to indicate activity on the port.

Amber light: Off when successful 100Mbps link is established. Typically on only briefly

at power up.

Under normal conditions, the Amber light will turn on immediately after the Ethernet

cable is first connected. This indicates that PoE power has been successfully applied.

Once the device connects to the network, it will switch to the Green light instead, which

will typically flicker indicating traffic on the network.

8063 IP Door Controller

Document 90-00106 Algo Communication Products Ltd (604) 454-3792

2020-09-02 4500 Beedie St Burnaby BC Canada V5J 5L2 [email protected]

Page 9 www.algosolutions.com

Reset

A recessed reset button (RST) next to the Ethernet Jack can only be used to reset the

8063 at time of power up. To return all settings to a factory default, wait until the SIP

LED flashes and then press and hold the reset button until the POWER LED begins a

double flash pattern. Release the reset button and allow the unit to complete its boot

process.

Do not press the reset button until the POWER LED begins flashing.

A reset will set all configuration options to factory default including the password.

8063 IP Door Controller

Document 90-00106 Algo Communication Products Ltd (604) 454-3792

2020-09-02 4500 Beedie St Burnaby BC Canada V5J 5L2 [email protected]

Page 10 www.algosolutions.com

TLS for SIP Signalling and Provisioning

Algo devices that support firmware 1.6.4 or later support Transport Layer Security (TLS).

This feature adds security by ensuring that Algo products can trust the hosted SIP

server. This is useful for when third-party devices or attackers may try to intercept,

replicate, or alter Algo products, and try to connect to the server. TLS protocol will

ensure that third parties cannot read/modify any actual data. Previously security was

less of a concern because phone systems were on isolated networks, but hosted

services are becoming increasingly more common. Using a hosted SIP service requires

traffic to be sent over the public internet and thus much more susceptible to attacks.

Signed certificates are an important piece in the Algo device’s operation, to ensure the

security, integrity, and privacy of its communication. Algo components that use TLS are

Provisioning and SIP Signaling.

These Algo devices each come pre-loaded with certificates from a list of trusted

certificate authorities (CA), which are installed in the hardware at the time of

manufacture. Note these pre-installed trusted certificates are not visible to users and are

separate from the ‘certs’ folder.

The TLS handshake happens to make sure that the client and server can trust each

other, and once that trust is established, the two parties can freely send encrypted data

and decrypt any data that they receive. After the TLS handshake process is complete, a

TLS session is established, and the server and client can then exchange messages that

are symmetrically encrypted with shared (pre-master) secret key.

For further details reference the Algo TLS guide for SIP Signalling and HTTPS

Provisionings.

Uploading Public CA Certificates to Algo SIP Endpoints

To install the public CA certificate on the Algo 8063, follow the steps below:

1. Obtain a public certificate from you Certificate Authority.

2. Rename the public certificate ‘siptrusted’ with any of supported formats (.pem,

.cert, or .cer).

3. In the web interface of the 8063, navigate to the System > File Manager tab.

4. Upload the certificate files into the ‘certs’ directory. Click the Upload button in the

top left corner of the file manager and browser to the certificate.

HTTPS Provisioning

Provisioning can be secured by setting the ‘Download Method’ to ‘HTTPS’ (under the

Advanced Settings > Provisioning tab). This prevents configuration files from being

read by an unwanted third-party. This resolves the potential risk of having sensitive data

stolen, such as admin passwords and SIP credentials.

Table des matières

Autres manuels Algo Contrôleurs

Algo

Algo 8300 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur