Alfain PEGAS 200 AC/DC PULSE Smart Manuel utilisateur
ALFA IN a.s. © www.alfain.eu PEGAS 200 AC-DC (Pulse) Smart manual ENG 03
WELDING INVERTER
PEGAS 200 AC/DC PULSE Smart
PEGAS 200 AC/DC Smart
OPERATING MANUAL
2/19
ALFA IN a.s. © www.alfain.eu
CONTENT
1 INTRODUCTION ....................................................................................... 3
2 SAFETY INSTRUCTIONS AND WARNINGS ............................................
3 TECHNICAL DATA .................................................................................... 6
EQUIPMENT ............................................................................................. 7
5 OPERATOR CONTROLS .......................................................................... 8
6 GETTING STARTED ............................................................................... 11
7 TWO STROKE AND FOUR STROKE IN TIG MODE ............................... 15
8 BASIC SETTINGS FOR TIG WELDING .................................................. 16
9 GENERAL INFORMATION ON THE WELDING MODES ........................ 17
10 ROUTINE MAINTENANCE & INSPECTION ............................................ 18
11 STATEMENT OF WARRANTY ................................................................ 19
12 DISPOSAL ............................................................................................... 19
3/19
ALFA IN a.s. © www.alfain.eu
1 INTRODUCTION
Congratulations on your new ALFA IN product. We are proud to have you as
our customer and will strive to provide you with the best service and reliability
in the industry.
This Operating Manual has been designed to instruct you on the correct use
and operation of your ALFA IN product. Your satisfaction with this product and
its safe operation is our ultimate concern. Therefore please take the time to
read the entire manual, especially the Safety Precautions. They will help you to
avoid potential hazards that may exist when working with this product.
Read and understand this entire Manual and your employer’s safety practices
before installing, operating, or servicing the equipment. While the information
contained in this Manual represents the Manufacturer's best judgement, the
Manufacturer assumes no liability for its use.
PEGAS 200 AC/DC PULSE Smart welds by those methods
1. E – (MMA) DC coated electrodes
2. E – (MMA) AC coated electrodes
3. TIG DC (Lift arc or High Frequency ignition)
. TIG AC (Lift arc or High Frequency ignition)
We reserve the law of adjustments and changes in case of printing errors,
change of technical paramaters, accessories etc. without previous notice.
These changes may not be reflected in the manuals for use in paper or
electronic form.
4/19
ALFA IN a.s. © www.alfain.eu
2 SAFETY INSTRUCTIONS AND WARNINGS
1. Once the packing has been opened, make sure that the machine is not
damaged. If in any doubt, call the service centre.
2. This equipment must only be used by qualified personnel.
3. During installation, any electric work must only be carried out by trained
personnel.
. The machine must be used in a dry place with good ventilation.
5. Make sure that no metal dust can be drawn in by the fan inside the
machine, as this could cause damage to the electronic circuits.
6. It is prohibited to connect more than one INVERTER generator in series
or in parallel.
7. When installing the machine, follow the local regulations on safety.
8. The position of the machine must allow easy access by the operator to
the controls and connectors.
9. When the welding machine is operating, all its covers and doors must be
closed and well fixed.
10. Do not expose the welding machine to direct sunlight or to heavy
rain. This equipment conforms to protection rating IP23S.
11. During welding, the welding cables must be located near or at
ground level. They should be as short as possible.
12. The operator must wear gloves, clothes, shoes, and a helmet or a
welder’s helmet, which protect and are fire-resistant in order to protect
him against electric shock, flashes and sparks from welding.
13. The operator must protect his eyes with safety visor or mask
designed for welding, fitted with standard safety filters. He should also be
aware that during electrical welding ULTRAVIOLET RADIATION is
emitted. Therefore it is vital that his face is also protected from radiation.
Ultraviolet rays produce the same harmful effect as sun burning on
unprotected skin.
1 . The operator is obliged to warn anyone near the welding area of
the risks that welding involves and to arrange to provide adequate
protection equipment.
15. It is very important to arrange for sufficient ventilation, especially
when welding in enclosed spaces. We suggest using suitable fume
extractors to prevent the risk of intoxication by fumes or gas generated
by the welding process.
16. The operator must ensure all flammable materials are removed
from the work area to avoid any risk of fire.
17. The operator must NEVER weld containers that have previously
contained petrol, lubricants, gas or similar flammable materials, even if
the container has been empty for a considerable time. THERE IS A
VERY HIGH RISK OF EXPLOSION.
18. The operator must be aware of all the special regulations which he
needs to conform to when welding in enclosed spaces with a high risk of
5/19
ALFA IN a.s. © www.alfain.eu
explosion.
19. To prevent electric shock, we strongly suggest the following rules:
20. Do not work in a damp or humid environment.
21. Do not use the welding machine if its cables are damaged in any
way.
22. Make sure that the earthing system of the electric equipment is
correctly connected and operational.
23. The operator must be insulated from the metal components
connected to the return wire.
2 . The earthing of the piece being worked could increase the risk of
injury to the operator.
EN 6097 -1 Standard: Open-circuit voltage. During the operation of the
machine, the highest voltage, with which it is possible to come into contact, is
the open-circuit voltage between the welding clamps.
The maximum open-circuit voltage of the welding machines is established by
national and international standards (EN 6097 -1) depending on the type of
weld current to be used, on its waveform and on the hazards arising from the
work place. These values are not applicable to the strike currents and those for
stabilisation of the arc that could be above it.
The open-circuit voltage, for as many adjustments as possible, must never
exceed the values relating to the various cases shown in the following table:
Case
Working conditions Open-circuit voltage
1 Places with increased risk of
electric shock
DC current: 113V
peak value
AC current: 68V
peak value and
8V effective
2 Places without increased risk
of electric shock
DC current: 113V
peak value
AC current: 113V
peak value and
80V effective
3 Torches held mechanically
with increased protection for
the operator
DC current: 1 1V
peak value
AC current: 1 1V
peak value and
100V effective
In case 1, the dc welding machines with rectifier must be built in such a way
that, in case of a fault developing in the rectifier (for example open circuit, short
circuit or lack of power), the permitted values cannot be exceeded.
25. Before opening the machine switch off the machine and disconnect
it from the power socket.
26. Only personnel authorised by this company can carry out
maintenance on the machine.
NOTE
Device complies with IEC 61000-3-12 with following conditions:
Short-circuit power Ssc of network in place at an interface between the user's
supply and the public network (PCC) must be least 99 kW.
User is obliged to consult with the electricity supplier if the impedance of the
network at this point is that required short-circuit capacity Zmax = 36 mΩ and
6/19
ALFA IN a.s. © www.alfain.eu
whether the device can be connected with a public low-voltage network.
On the nameplate are the following symbols: .
ELECTROMAGNETIC COMPATIBILITY
The welding device is in terms of interference designed primarily for industrial
areas. It meets the requirements of EN 6097 -10 class A and it isn’t designed
for using in residential areas, where the electrical energy is supplied by public
low-voltage power supply network. It can be here potential problems with
ensuring of electromagnetic compatibility in this areas, due to interference
caused by power lines as well as the radiated interference.
During operation, the device may be the source of interference.
Caution
We warn users, that they are responsible for possible interference from
welding.
3 TECHNICAL DATA
Met od MMA - AC MMA - DC TIG - AC TIG - DC
Mains voltage V/Hz
1x230/50-60
Welding current range A/V
10 - 170 10 - 170 10 -200 10 - 170
Open-circuit voltage U20 V 53,0 63,0 53,0 63,0
Mains protection A 16 @ (25 @)
Max. effective current I1eff A 16,0 (22,5) 16,0 (16,6)
Welding current (DZ=100%)
I2 ta=40 oC A 80 (110) 80 (110) 120 (120) 120(120)
Welding current (DZ=60%)
I2 ta=40 oC A 100 (140) 100 (140) 140 (140) 140 (140)
Welding current (DZ=x%) I2
ta=40 oC A 20%=170
(40%=170)
20%=170
(40%=170)
30%=200
(35%=200)
40%=170
(40%=170)
Protection IP23S
Standards EN 60974-1, EN 60974-10 cl. A
Dimensions (W x L x H) mm
130 x 430 x 230
Weig t kg 8,5
The machine is equipped with a 16 A plug for connection to a single phase
supply 1 x 230 V, the corresponding data for this 16 A plug (Duty Cycle = DC)
are in the table above without brackets.
In order to fully use the technical capabilities of the machine, the machine must
be connected to the industrial single phase networks with a blue plug 32 A with
the maximum permissible fuse of 25 A. The corresponding data for such a 32
A plug are stated in the table above in brackets.
7/19
ALFA IN a.s. © www.alfain.eu
Another option is to connect the machine to the three-phase mains 3x 00 /
230V TN-S (CS). The condition is to use a 5 pin 32 A plugs for the supply
cable and connection to the phase voltage. Black (brown) wire connected to
one phase (e.g. L1), the blue wire to the neutral wire (N) and green-yellow wire
to the grounded conductor "PE". In this case, it is possible to connect the
machine to a three-phase socket, which may be protected by fuse max. 25 A.
Attention! Do not connect to the interconnected voltage (delta voltage)
(between 2 phases)!
Replacement of the plug may only be performed by ALFA IN authorized
service personnel.
ALFA IN continuously strives to produce the best product possible and
therefore reserves the right to change, improve or revise the specifications or
design of this or any product without prior notice. Such updates or changes do
not entitle the buyer of equipment previously sold or shipped to the
corresponding changes, updates, improvements or replacement of such items.
4 EQUIPMENT
CONTENT OF DELIVERY
Item No. Description Qu ntity
5.0279 PEGAS 200 AC/DC PULSE SMART 1
5.0278 PEGAS 200 AC/DC SMART 1
58 7 Set of Connectors for PEGAS AC/DC Smart 1
8. 62.12 Quick connector Pegas 160 female 1
In case you order a torch with the connector on, the set 5756 would be used
for that purpose and will not be delivered then. In case you order a Gas Hose,
the quick connector 8. 62.12 would be used for that purpose and will not be
delivered then.
ACCESSORIES TO ORDER
Item No. Description
VM0321-2 Hose Gas PEGAS OVO 3m G1/
VM0253 Welding Cable Set 2x 3m 35-50 200A
5.0508 Welders Cart P 80
17FSL S Torch PARKER SGT 17 m 35-50 FX S
17FSL SUD Torch PARKER SGT 17 m 35-50 FX S UD
17FSL8S Torch PARKER SGT 17 8m 35-50 FX S
17FSL8SUD Torch PARKER SGT 17 8m 35-50 FX S UD
26FSL S Torch PARKER SGT 26 m 35-50 FX S
8/19
ALFA IN a.s. © www.alfain.eu
26FSL SUD Torch PARKER SGT 26 m 35-50 FX S UD
26FSL8S Torch PARKER SGT 26 8m 35-50 FX S
26FSL8SUD Torch PARKER SGT 26 8m 35-50 FX S UD
6008 Pressure Reducer FIXICONTROL Ar 2 manometers
5.017 ST Foot Pedal Remote CTRL 3 m PEGAS incl. Connector ST
5 OPERATOR CONTROLS
MAIN PARTS
Fig . 1 Main parts
Pos. Description
A1 Operating panel
A2 Quick connector +
A3 Gas connector of the welding torch
A Torch control connector
A5 Quick connector -
A6 ON/OFF switch
A7 Gas inlet
A8 Mains cable and plug
9/19
ALFA IN a.s. © www.alfain.eu
OPERATING PANEL
Fig. 2 PEGAS 200 AC/DC Pulse Smart
Fig. 3 PEGAS 200 AC/DC Smart
Pos. Description
1 LED MMA
2 LED TIG LA – Lift Arc ignition
3 Button switch MMA/TIG HF/TIG LIFT ARC.
LED HF. If illuminated the HF ignition was set.
10/19
ALFA IN a.s. © www.alfain.eu
5 Button switch AC/DC mode
6 LED AC
7 LED DC
8 LED Two Stroke (2T).
9 Button TIG 2T or T (two stroke, four stroke)
10 LED Four Stroke ( T)
11 Encoder
12 LED Pregas. 0,0 – 2,0 s
13 LED start current (just T), 10 – 170 A DC, 10 – 200 A AC.
1 LED Up slope. 0 – 10 s.
15
LED – non pulse mode. To change, turn the encoder 11 and
confirm by means of pressing the encoder 11 down. Display 31
shows ---
16 LED Main Welding Current. 10 - 170 A (TIG-DC)；10 - 200 A (TIG-
AC)； 10 – 170 A (MMA-AC/DC)
17 LED – PULSE selected To change, turn the encoder 11 and confirm
by means of pressing the encoder 11 down. Display 31 shows -P-
18 LED lower current, 10 – 170 A (TIG-DC)；10 – 200 A (TIG-AC)；
10 – 170 A (MMA-AC/DC)
19 LED ratio of the pulse current and the base current . 5 – 95 %. Just
for the pulse mode.
20 LED Pulse Frequency. 0,5 – 200 Hz. Just for the pulse mode.
21 LED Down Slope, 0 – 10 s
22 LED Balance (just TIG AC). Used for elimination of the aluminium
oxides. Range +5 to -5, (more in the text below).
23 LED end current, 10 – 170 A DC, 10 – 200 A AC, just in T.
2 LED Post Gas, 0 – 10 s.
25 LED Time (s). If illuminated there are values in s on the display.
26 LED %. If illuminated there are values in % on the display.
27 LED Hz. If illuminated there are values in Hz on the display.
28 LED HOT START, just for MMA, 0 – 100. LED lights up after
pressing the encoder 11.
29 LED welding current MMA 10 – 170 A, just for MMA. LED lights up
after pressing the encoder 11.
30 LED ARC FORCE just for MMA, 0 – 100. LED lights up after
pressing the encoder 11.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Alfain Système de soudage
Alfain
Alfain ALFIN 161 W MG120-1 Manuel utilisateur
Alfain
Alfain PEGAS 250 E CEL Manuel utilisateur
Alfain
Alfain PEGAS 320 AC/DC PULSE Manuel utilisateur
Alfain
Alfain ALF 251 aXe Manuel utilisateur
Alfain
Alfain 5.0291 Manuel utilisateur
Alfain
Alfain PAN 161 Manuel utilisateur
Alfain
Alfain PEGAS 60 PLASMA Manuel utilisateur
Alfain
Alfain aXe 320 double pulse Manuel utilisateur
Alfain
Alfain 5.0238-3 Manuel utilisateur
Alfain
Alfain PEGAS 400 E CEL Manuel utilisateur
Alfain
Alfain PERUN 200 MIG MAN PFC Manuel utilisateur
Alfain
Alfain PAN 160 Manuel utilisateur
Alfain
Alfain PEGAS 350 AC/DC PULSE Manuel utilisateur
Alfain
Alfain PEGAS 161 E softswitch Manuel utilisateur
Alfain
Alfain SVAROG 420 HD Manuel utilisateur
Alfain
Alfain PEGAS 250 MIG MAN Manuel utilisateur
Alfain
Alfain PEGAS 101 PLASMA Manuel utilisateur
Alfain
Alfain PEGAS 200 MIG MAN PFC Manuel utilisateur
Alfain
Alfain aXe 200 IN PFC Manuel utilisateur
Alfain
Alfain alfin 281 w Manuel utilisateur
Manuels Système de soudage populaires d'autres marques
TAFA
TAFA 30*8B35 Manuel utilisateur
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur
ESAB
ESAB Buddy Arc 145 Manuel utilisateur
CIGWELD
CIGWELD 636804 Guide rapide
Red-D-Arc
Red-D-Arc DC-400 Manuel utilisateur
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur
