Alderon Industries Versa'larm VA02B Manuel utilisateur
1. DISCONNECT ALL ELECTRICAL SERVICE BEFORE INSTALLING OR WORKING ON THE PRODUCT.
2. DO NOT USE WITH FLAMMABLE OR EXPLOSIVE FLUIDS SUCH AS GASOLINE, FUEL OIL, KEROSENE, ETC.
DO NOT USE IN EXPLOSIVE ATMOSPHERES.
3. ALARM PANEL MUST BE MOUNTED INDOORS. FOR OUTDOOR APPLICATIONS CONSULT FACTORY.
1. Phillips screw driver
2. (Qty 2) #6 self tapping screws
3. Access to 120 VAC power receptacle
4. Optional - Plastic anchors (#8; Qty 2) if mounting to sheet rock
5. Optional - 9V battery (used for battery backup during power outages)
6. Optional - Wire stripper (used if you need to strip wire to connect to a BAS or SCADA system)
7. Optional - Needle nose pliers if using auxiliary contacts
Versa’larm™
Operation, Maintenance and Installation Manual
Introduction of Installation
Safety Guidelines
Description of Operation
Tools, Supplies and Requirements for Installation - Not Included
2-Zone Alarm - Model VA02B
Normally Open / Normally Closed
The 2-Zone Normally Open / Normally Closed Versa’larm™alarm panel is powered by 120 VAC coming from standard wall
outlets and is transformed to 9-11.1 VDC. Installing a 9 Volt battery provides battery backup during power outages. The
power LED (green) will illuminate when powered. The Normally Open / Normally Closed Versa’larm™is a multipurpose
alarm panel where a normally open switch (Zone 1 signaling device) such as a float switch, water sensor, sump probe
sensor, or any normally open “dry contact” can be wired to the alarm panel and a normally closed switch (Zone 2 signaling
device) such as a temperature or security switch is wired in series to the alarm panel.
The alarm panel buzzer will annunciate, alarm LED(s) (red) will illuminate, and the built in auxiliary contacts will be activated
when either Zone 1 or Zone 2 senors “change state” (normally open close or normally closed open). The auxiliary contacts
can be used to connect to an Alderon Industries Auto Dialer, an existing alarm security system, or building automation
system (BAS).
Pressing the “Alarm Silence” pushbutton will silence the buzzer and the alarm LED(s) (red) for the specific zone(s) will
remain on. When the alarm condition is cleared (sensor(s) reverting to normal condition), the system automatically resets
itself for the next alarm cycle.
Before proceeding with the installation or operation of the product, read all
instructions thoroughly, as well as complying with all federal, state and local
codes, regulations, and practices. The product must be installed by qualified
personnel familiar with all applicable local electrical and mechanical codes.
Refer to the National Electrical Code (NFPA 70). Failure to properly install and
test this product can result in personal injury or equipment malfunction.
Alarm Systems Control Panels Float Switches Leak Detection Systems Page 1 of 4
1B1A 1C 1D2A 2B
Versa’larm™
Operation, Maintenance and Installation Manual
Installation of the Alarm Panel
1. To install/replace the battery for the backup power feature, remove the access cover (Fig. 1) and install 9 VDC battery
(Duracell model MX 1604B2 / Fig. 2). After installing battery, the green power and loop closed LEDs should illuminate, then
press and hold the “Alarm Test” pushbutton (Fig. 3) to activate the alarm and make sure the battery is working properly. The
buzzer should annunciate and the alarm LEDs should illuminate. If using the auxiliary contacts, leave the access cover off
until step 3 is completed. If the auxiliary contacts are not used, replace the access cover (Fig. 4).
(Fig. 1) (Fig. 2) (Fig. 3) (Fig. 4)
2. Determine the mounting location for the alarm panel. Make sure power outlet (120 VAC, 50/60 Hz) is within 5-feet of the
alarm panel (Fig. 5). The power outlet should be on a separate circuit breaker from any other device and not on a switched
receptacle to maintain power integrity. Mount the alarm panel using two #6 self-tapping screws (not included / Fig. 6). Use
two #8 plastic anchors (not included / Fig. 7) if mounting the alarm panel to sheet rock.
(Fig. 5) (Fig. 6) (Fig. 7)
5 ft. Max
3. If auxiliary contacts are not used, go to step 5. Refer to wiring diagram below (Fig. 8) for auxiliary contact wiring. Zone 1
has two sets of auxiliary contacts. Terminals 1A and 1B are normally open that close when in alarm condition. Terminals 1C
and 1D are normally closed that open when in alarm condition. Zone 2 has one set of auxiliary contacts. During normal
conditions where power is applied to the alarm panel and a normally closed sensor is connected, Terminals 2A and 2B will
be open. Terminals 2A and 2B will close when a normally closed sensor opens or if there is power loss. If connecting to an
existing alarm security system or building automation system (BAS), use 18 gauge 2-conductor wire. When connected,
replace the access cover and pull wire(s) through the knockout(s) on the access cover (see step 4). CAUTION! - Route all
wires away from sharp objects and internal components when installing wires.
AUXILIARY CONTACTS:
Terminals 1A and 1B - Normally Open
Terminals 1C and 1D - Normally Closed
Terminals 2A and 2B - Normally Open
(close on alarm or power loss)
Class 2, 24 VDC/VAC (50/60 Hz)
100 Milliamps Maximum
(Fig. 8)
2-Zone Alarm - Model VA02B
Normally Open / Normally Closed
ZONE 2
Close
on Alarm
or
Power Loss
Close
on Alarm
Open
on Alarm
}
}
}
ZONE 1 ZONE 1
2A 2B 1A 1B 1C 1D
Alarm Systems Control Panels Float Switches Leak Detection Systems Page 2 of 4
Versa’larm™
Operation, Maintenance and Installation Manual
Installation of the Alarm Panel Continued
4. After the access cover has been removed from the alarm panel (Fig. 9), use a needle nose pliers (not included) to remove
the desired “break away tabs” from the access cover, lightly pull and twist off tab(s) (Fig. 10). Replace the access cover and
run wire(s) through the knockout(s) (Fig. 11).
(Fig. 9) (Fig. 10) (Fig. 11)
5. Make note of the alarm condition(s) you are monitoring and write them on the provided label, located on the right side of
the alarm panel.
2-Zone Alarm - Model VA02B
Normally Open / Normally Closed
6. Connect one or more normally open sensors (rated 9 VDC, 200 mA Minimium) to Terminals C and 1. When using multiple
normally open sensors, they are wired in “parallel” (Fig. 12). Connect one or more normally closed sensors (rated 9 VDC,
200 mA Minimum) to Terminals C and 2. When using multiple normally closed sensors, they are wired in “series” (Fig. 12).
Note: When using multiple sensors, a wire nut connection may be required for all sensors connected to Terminal C and from
that wire nut connection, bring only a single 18 gauge wire to Terminal C on the alarm panel.
An optional 9-12 VDC Indoor/Outdoor LED Strobe Beacon (Alderon P/N: 7933) can be connected to Terminals C and 3.
Connect the Red Wire (+) from the LED Strobe Beacon to Terminal C on the alarm panel and connect Black Wire (-) from
the LED Strobe Beacon to Terminal 3 on the alarm panel. As required, use appropriate junction box and conduit to connect
from the alarm panel to the LED Strobe Beacon. The LED Strobe Beacon may be mounted indoor or outdoor for a remote
indication of alarm activation.
(Fig. 12)
}
}
Normally Open
Sensors in Parallel
ZONE 1
Normally Closed
Sensors in Series
ZONE 2
Indoor / Outdoor
LED Strobe Beacon (alarm)
BEACON
Multiple sensors can be
used on each zone
NOTE:
Alarm Systems Control Panels Float Switches Leak Detection Systems Page 3 of 4
Versa’larm™
Operation, Maintenance and Installation Manual
Installation of the Alarm Panel Continued
7. Plug the alarm panel power supply into a 120 VAC, 50/60 Hz
standard wall outlet and the green “Power” and “Loop Closed”
LEDs should illuminate (Fig. 13).
Testing the Alarm Panel
1a. Test the alarm panel by pressing and holding the “Alarm Test” pushbutton (Fig. 14). The buzzer should annunciate and
the alarm LEDs should illuminate. Press the “Alarm Silence” pushbutton and the buzzer should silence while the alarm LEDs
remain on. After you remove pressure from the “Alarm Test” pushbutton, the “Auto Reset” feature reactivates the alarm
panel for the next alarm cycle.
1b. Test the Zone 1 normally open sensor(s) (Fig. 15). Activate the normally open sensor(s) so that the contact “closes”, the
buzzer should annunciate and Alarm 1 LED should illuminate. The alarm panel auxiliary contacts 1A and 1B should close
and auxiliary contacts 1C and 1D should open. When the sensor(s) state reverts back to normal, the alarm condition will
clear and the “Auto Reset” feature reactivates the alarm panel for the next alarm cycle.
1c. Test the Zone 2 normally closed sensor(s) (Fig. 16). Activate the normally closed sensor(s) so the contact “opens”, the
buzzer should annunciate and the Alarm 2 LED should illuminate. The auxiliary contacts 2A and 2B on the alarm panel
should open. When the sensor(s) state reverts back to normal, the alarm condition will clear and the “Auto Reset” feature
reactivates the alarm panel for the next alarm cycle.
1d. Test the Zone 2 loop test (Fig. 17, Fig. 18, and Fig. 19). The loop testing of the normally closed sensors can be
performed without activating the alarm or auxiliary contacts. This test is performed when wiring all of the normally closed
sensors in “series” and it’s desired to test/activate each sensor during installation to make sure the wiring is correct. Place
the Zone 2 Testing Only switch to the “Test” position, if all the normally closed sensors are correctly wired in “series” and
connected to Terminals C and 2 on the alarm panel, the “Loop Closed” LED should illuminate (Fig. 17). Activating the first
normally closed sensor so the contact “opens” should cause the “Loop Closed” LED to turn off (Fig. 18). Test the remaining
normally closed sensors that are wired in “series”, when each one is activated they should also cause the “Loop Closed”
LED to turn off. After all sensors have been tested, place the Zone 2 Testing Only switch to the “Armed” position (Fig. 19)
and the “Loop Closed” LED should illuminate indicating the “Auto Reset” feature is reactivated on the alarm panel for the
next alarm cycle.
2-Zone Alarm - Model VA02B
Normally Open / Normally Closed
(Fig. 13)
5 ft. Max
(Fig. 14) (Fig. 15)
(Fig. 16)
(Fig. 17) (Fig. 18) (Fig. 19)
Alarm Systems Control Panels Float Switches Leak Detection Systems Page 4 of 4
Table des matières
Autres manuels Alderon Industries Système de sécurité
Alderon Industries
Alderon Industries Sump Advisor 2000514 Manuel utilisateur
Alderon Industries
Alderon Industries Sump Advisor 2000514 Manuel utilisateur
Alderon Industries
Alderon Industries Power Post VA-02 Manuel utilisateur
Alderon Industries
Alderon Industries VersAlarm I/O VLIO-00005 Manuel utilisateur
Alderon Industries
Alderon Industries Versa'larm VA01D Manuel utilisateur
Alderon Industries
Alderon Industries Versa'larm 4X Manuel utilisateur
Alderon Industries
Alderon Industries VersAlarm I/O VLIO-0002 Manuel utilisateur
Alderon Industries
Alderon Industries VersAlarm I/O VLIO-00005 Manuel utilisateur
Alderon Industries
Alderon Industries Versa'larm VA01A Manuel utilisateur
Alderon Industries
Alderon Industries VersAlarm 4X Manuel utilisateur
Alderon Industries
Alderon Industries Oil Alert VA03 Manuel utilisateur
Alderon Industries
Alderon Industries WaterPro WaterSpotter AVFD Series Manuel utilisateur
Alderon Industries
Alderon Industries VersAlarm I/O VLIO-0001 Manuel utilisateur
Alderon Industries
Alderon Industries 7001 Versa’larm Manuel utilisateur
Alderon Industries
Alderon Industries 8059 Manuel utilisateur
Alderon Industries
Alderon Industries VersAlarm I/O Manuel utilisateur
Alderon Industries
Alderon Industries Versa'larm 8124 Manuel utilisateur
Alderon Industries
Alderon Industries Wireless Versa'larm VA01B Manuel utilisateur
Alderon Industries
Alderon Industries Versa'larm VA02A Manuel utilisateur
Alderon Industries
Alderon Industries Vizzyalarm VZW-02 Manuel utilisateur
Manuels Système de sécurité populaires d'autres marques
EDM
EDM Solution 6+6 Wireless-AE Manuel utilisateur
Highway Safety Group
Highway Safety Group EA401 Manuel utilisateur
Siren
Siren LED GSM Manuel utilisateur
Detection Systems
Detection Systems 7090i Instructions de montage
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuel utilisateur
Siemens
Siemens FDM273 Manuel utilisateur