Alcovisor Jupiter Manuel utilisateur

MODEL: JUPITER

Instruction Manual

TABLE OF CONTENTS

STRUCTURES……………………………………………………………………… 1

INSTRUMENT FEATURES……………………………………………………….. 2

ICON DESCRIPTION……………………………………………………………… 3

INTRODUCTION ………………………………………………………………….. 4

OPERATING INSTRUCTIONS…………………………………………………… 5

PRINTER…………………………………………………………………………… 9

TOUCH SCREEN CALIBRATION……………………………………………….. 9

P. 1

STRUCTURES

Operator needs to read operation manual and familiar with the

operation before using. Retain the manual for future reference.

P. 2

INSTRUMENT FEATURES

PLEASE REFER TO DIAGRAME ON PAGE 1

1. DISPOSABLE MOUTHPIECE

For sanitary reason, each mouthpiece is individually packed and sealed.

New mouthpiece should be attached to sample port for each test to prevent

any contamination from the previous sample.

2. SAMPLING CUP

Sampling Cup is reusable. Attach sampling cup to the sample port. Do not

touch the sampling cup with the mouth while providing a breath sample.

Remove the sampling cup after use and clean it by alcohol for next use.

3. BUTTON TO REMOVE MOUTHPIECE

For sanitary reason, the mouthpiece can be removed by push the button

underneath the mouthpiece.

4. TOUCH SCREEN DISPLAY

A touch screen display that will display corresponding instructions and alcohol

concentration of the subject being test. Select the icons and buttons on the

screen by using the stylus pen provided.

5. ON/OFF BUTTON

Press and hold the On/Off button to turn on or turn off the device.

6. BATTERY CHARGING

Battery can be charged inside the device. The battery charging indicator

turns red when the battery is charging, when the battery is fully charged, the

indicator turns green.

7. EXTERNAL POWER CONNECTORS

Connectors for 12V car (cigarette) adapter or optional 12V power transformer.

Battery can be charged inside the device.

8. USB connector

Use an USB cable to upload test records stored in the memory and upgrade

the software.

P. 3

ICON DESCRIPTION

1 GPS Indicator 8 GPS

2 Battery Indicator 9 PC Connection

3 Date & Time Indicator 10 Date & Time Setting

4 Standard Test with Input 11 Setting

5 Standard Test without Input 12 Advanced Setting

6 Screening Test 13 Last Calibration Date

7 Test Records 14 Test Record Counter

Previous Screen/Cancel Next Screen/Confirm Main Screen

Print Repeat Test

P. 4

INTRODUCTION

It is a state of the art instrument used to detect Ethyl Alcohol from a valid breath

sample. It uses an electrochemical fuel cell to measure the concentration of

alcohol from the sample of the expired breath from a human subject. If alcohol

is present, a corresponding voltage is generated from the fuel cell, which is

proportional to the alcohol content of the sample provided by a human subject.

This voltage is then sent to the CPU and converted to a subject’s BAC which is

then displayed.

Instrument Features:

1. Test record storage is more than 32,000 entries depending on the length of

the records being stored. Capability of uploading test records for record

keeping.

2. Use disposable mouthpieces or sampling cups to prevent foreign matter from

entering.

3. A hard plastic case is included for storing the device and accessories for easy

transport. When not in use, the device and accessories should be stored in

this plastic case to prevent damage.

4. Ability to run as often as needed. Recovery time between tests on average

is 30 seconds between positive tests.

5. Powered by High-capacity lithium battery. Battery is located behind the

sliding cover on the back of the device. The level of power left in the battery

is indicated on the screen. A cigarette plug adapter is also included for use

by the operator.

6. Storage temperature range is -25°C to 70°C, storage humidity is 15% to 90%,

inappropriate storage of the device will shorten the lifespan of the fuel cell

sensor.

P. 5

OPERATING INSTRUCTIONS

Pre-test Conditions

1. Operating temperature range is -10°C to 50°C. Use within this temperature

range will limit condensation from a subject breath to insure an accurate an

accurate reading from a breath sample.

2. It is recommended that the operator to observe a subject for about 20 minutes

before administering the breath test to insure that nothing is consumed or

expelled from the mouth of the subject. Following this procedure will

eliminate reading from mouth alcohol.

Standard Test with Input

1. Attach a disposable mouthpiece onto the sample port.

2. Input information by a stylus pen.

NOTE: Maximum 16 characters for each input.

3. When displays “Please Blow”, take a deep breath and blow until BEEP tone

stops.

4. Test result displays on the display.

5. Select to print the test result.

6. Select to start another test.

7. If testee did not blow within 30 seconds, tester can select “Refuse” to confirm

the testee refused to do the test; or select “Test Again” to allow testee to do

the test again.

8. If testee failed to give a valid breath sample, tester can select “Discontinue” to

confirm; or select “Test Again” to allow testee to do the test again.

9. A passive test can be performed by select “Passive” during the testee is

blowing.

10. Push the button underneath the mouthpiece to remove the mouthpiece.

P. 6

Standard Test without Input

1. Attach a disposable mouthpiece onto the sample port.

2. Follow steps “3-10” of “Standard Test with Input”.

Screening Test

1. Attach a sampling cup onto the sample port.

2. When displays “Please Blow”, take a deep breath and blow to the sampling

cup until BEEP tone stops.

3. “Alcohol Detected” or “No Alcohol” displays on the display.

4. A passive test can be performed by select “Passive” during the testee is

blowing.

5. Select to start another test.

6. If “Alcohol Present”, use mouthpiece to perform a standard test to obtain an

accurate test result with reading.

NOTE: Screening Test is only used for screening tests, it is to check whether

alcohol is found in the breath sample. An accurate test result can only be

obtained by standard test.

NOTE: Test records of the screen tests cannot be printed nor stored.

GPS

1. Longitude and Latitude of location of the device will be shown.

2. Longitude and Latitude of the test is stored and printed on the printout.

NOTE: GPS system only functioned 5-10 minutes after turn on the device. It

can only receive signal in open area. If there is no GPS signal, the Longitude

and Latitude will not be shown on the printout.

P. 7

Test Record

1. Over 20,000 test records can be stored, depending on the length of the

records.

2. Individual test record can be printed by selecting .

3. Use or to move to the previous or next record.

4. Press On/Off button (right button) to move 10 records forward, and press

Function button (left button) to move 10 records backward.

5. Press On/Off button (right button) and Function button (left button) together to

jump to the record needed.

First: Jump to first Record

End: Jump to end Record

0 00 00: Jump to a specific record, e.g. 0 01 00 means jump to record 100; 1

12 00 means jump to record 11200.

Connect to PC

1. Test records can be downloaded PC for analysis.

2. Connect the device and the PC by a USB cable.

3. Please refer to Database Instruction for downloading the test records.

Date & Time Setting

1. Set correct Date and Time.

2. Select “Update” to confirm.

P. 8

Setting

1. Auto Off

i. Select time limit to turn off the device automatically.

ii. Select to confirm

2. Print

i. Select “Auto Print” to print the result automatically after each test without

selecting “Print”.

ii. Select number of printout copies needed for test result equal to 0 ( =0 )

and exceed 0 ( >0 ).

iii. Select to confirm.

NOTE: If no printout needed for a test result equal to 0, select “0” for

“=0”.

3. Sound

i. Adjust the level of BEEP tone.

First bar: sound level of BEEP tone.

Second bar: length of the BEEP tone.

ii. Select to confirm.

4. Cali

i. When the screen displays “Calibration Needed”, send the device for

calibration.

ii. A password is needed for calibration to ensure calibration is performed

by eligible persons.

iii. Please refer to Calibration Instruction.

Advanced Setting

1. Only legitimated persons are allowed for advanced setting.

2. A Password is needed.

3. Please refer to Advanced Setting Instruction.

Autres manuels pour Jupiter

Table des matières

Autres manuels Alcovisor Équipement de test

Alcovisor

Alcovisor Jupiter Manuel utilisateur

Alcovisor

Alcovisor Alpha Manuel utilisateur

Alcovisor

Alcovisor Deimos Manuel utilisateur

Alcovisor

Alcovisor JUPITER X Manuel utilisateur

Alcovisor

Alcovisor Satellite Manuel utilisateur

Alcovisor

Alcovisor BAC-100 Manuel utilisateur

Alcovisor

Alcovisor Beta Manuel utilisateur

Alcovisor

Alcovisor Mercury Manuel utilisateur

Alcovisor

Alcovisor Saturn Manuel utilisateur

Alcovisor

Alcovisor Mark X Manuel utilisateur

Alcovisor

Alcovisor Mercury Manuel utilisateur

Alcovisor

Alcovisor Jupiter Manuel utilisateur

Alcovisor

Alcovisor BAC-100 Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur