AlcoLimit WORKSafe Manuel utilisateur
WORKSafe©
AlcoLimit©
User Manual
AlcoLimit Breathalysers Pty. Ltd.
P.O. Box 1106,
MANLY, NSW, 1655
Ph: 1300 667 661
www.alcolimit.com.au
WORKSafe©
AlcoLimit©
pg-3
CONTENTS
Description Page
Parts of your breathalyser ................................................................ 4
Specications ...................................................................................... 5
Set-up your breathalyser .................................................................. 6
Basic operation - Normal Mode/Fast Mode ................................... 7-8
Troubleshooting Guide ..................................................................... 9
Accessing the menu ...........................................................................
- Last tests
- Last maintenance
- Total test count
- Date & Time
- Measurement mode
- Set date
- Set time
- Set Language
- Backlight
- Printer
- Save to SD card
- Bluetooth
- Change user PIN
- Set Contrast
10
11
11
11
11
12
12
12
12
13
14
15
16
16
16
Warnings .............................................................................................. 17
Storage Conditions ............................................................................ 17
Replacing the sensor module .......................................................... 18-19
Recalibration ....................................................................................... 20
Warranty .............................................................................................. 21
Disclaimer ............................................................................................ 21
Service Record .................................................................................... 22
pg-4
WORKSafe©
AlcoLimit©
IMPORTANT INFORMATION
If you do not follow the instructions for use your test results may be
inaccurate and your warranty may become void.
For most accurate results, it’s important to wait at least 20 minutes after smoking, eating or drink-
ing before testing. This is a universal principle for all breathalysers, not just yours. The reason being
is that if you have recently consumed alcohol, the residual alcohol in your mouth is very high and
can cause a false reading. Additionally, waiting 20 minutes allows the alcohol to be absorbed from
your stomach into your bloodstream, contributing to more accurate test results.
PARTS OF YOUR BREATHALYSER
Breath Inlet /
Mouthpiece
Infrared Indicator
(IrDA)
USB / Printer Connector
Breath Outlet
ON / OFF Button
Indicator Light
Down Arrow
Up Arrow
LCD Display
pg-4 pg-5
WORKSafe©WORKSafe©
AlcoLimit©
SPECIFICATIONS
Recommended Usage Professional
Sensor Type Replaceable Electrochemical Fuel Cell
Accuracy Conforms to Australian Standard AS3547
Range %BAC 0.000 - 0.500
Display LCD
Warm-up time 5 seconds - 2 minutes
Breath Sampling Time 5 seconds
Temperature Operation -50C - 400C
Storage -100C - 500C
Housing Shock Resistant Plastic
Weight 198 grams
Power Source 2 x AA Alkaline Batteries
Dimensions 133cm x 64cm x 33cm
Warranty 12 Month Limited Warranty
Recalibration Period Every 6 months
Specications are subject to change for the purpose of product improvement.
For all after-sales service and enquiries please contact the manufacturer:
AlcoLimit Breathalysers Pty. Ltd.
P.O. Box 1106
Manly, N.S.W. 1655
Australia
Ph: 1300 667 661 or +612 9939 3077
Website: www.alcolimit.com.au
Breath Inlet /
Mouthpiece
pg-6
SET-UP YOUR BREATHALYSER
Inserting the batteries
Open the rear battery cover by sliding
the top latch to the right and press the
battery cover downward.
Insert 2 x AA 1.5v alkaline batteries
or 2 x 1.2v rechargeable batteries.
Ensure the polarity is correct.
Replace the battery cover. (Hook the 2
metal clips in at the top and slide the battery
cover upwards until it secures in place.)
Note: do not charge rechargeable batteries
in the breathalyser. Always remove recharge-
able batteries and charge in a separate
charger.
Attaching the mouthpiece for
NORMAL MODE
Attach the mouthpiece as shown,
ensuring it is secured with a ‘click’.
The mouthpiece may be used with a left
or right orientation to suit both left and
right handed use.
To remove the mouthpiece, rmly grasp the larger open end and lever upwards
until the mouthpiece‘unclicks’.
Use a new mouthpiece for every test.
Attaching the mouthpiece for
FAST MODE
Fast mode requires a funnel shaped mouthpiece
which may be re-used for multiple tests.
Simply attach the mouthpiece to the top of the
breathalyser with the funnel facing upwards.
To remove the mouthpiece, simply pull directly upwards.
WORKSafe©
AlcoLimit©
pg-6 pg-7
BASIC OPERATION - NORMAL MODE / FAST MODE
WORKSafe©
AlcoLimit©
Depress the ON/OFF button for 2 seconds until the
breathalyser turns on.
The initial screen will display the Date, Time & Serial
Number of the device
The word WAIT will appear on the display along with
the number of tests performed since the last calibra-
tion.
There is also an indication of the battery strength.
When the word BLOW appears, blow into the mouth-
piece with a strong consistent breath. A beep will
sounds while air is being accepted.
Once the correct amount of air is received the breath-
alyser will stop beeping and start analysing the sam-
ple.
Quick toggle between modes
Once the word BLOW appears you may toggle be-
tween NORMAL MODE and FAST MODE by pressing
the UP arrow. The letter‘N’or ‘F’ will appear in the top
right hand corner of the screen. Only available when
the breathalyser is preset in FAST MODE. See pg. 12.
The word ANALYSING will appear on the display while
the breathalyser is analysing the air sample. This usu-
ally takes only a few seconds.
pg-8
WORKSafe©
AlcoLimit©
In NORMAL MODE operation a 3 decimal place result will
appear on the display and remain for 15 seconds.
eg. 0.051%BAC
If you wish to retest, press the On/Obutton again.
In FAST MODE operation either the word PASS or FAIL
will appear on the display indicating the presence or
absence of alcohol.
The PASS level is 0.000 %BAC by default but can be
custom set at any level to suit your organisation upon
request. eg. 0.020%BAC or 0.050%BAC
In FAST MODE the breathalyser will automatically reset
for the next test.
Turning othe power
The breathalyser will turn oautomatically after 15 seconds of non-use.
To force the breathalyser to shut-down, press and hold the on/obutton for 3 seconds until the
display counts down and the breathalyser turns o.
IMPORTANT INFORMATION
This device is tested as a 0.05% BAC device (0.05%BAC is equal to 0.05grams of alcohol per 100ml of
blood).
ALCOLIMIT WORKSafe has a range of 0.000-0.500 %BAC.
PLEASE NOTE: Alcohol vapour on your breath will cause a higher reading. We recommend having a glass of
water prior to testing and waiting at least 20 minutes after your last drink for accurate results. Not waiting the
required 20 minutes will saturate the sensor unnecessarily and may cause sensor damage. This is not covered
under your warranty. Please always wait 20 minutes after consuming any alcohol to avoid this problem.
pg-8 pg-9
WORKSafe©
AlcoLimit©
TROUBLESHOOTING GUIDE
Indication on display Solution
Insucient breath has been detected by the sensor.
Restart the breathalyser and ensure you are blowing a
strong consistent breath. Continue blowing until the
beeping sound stops. This indicates it has received a
sucient air sample.
The level of charge in the batteries is almost 0%.
Change your batteries.
100% 70% 30% 0%
An indication is provided on the display with an esti-
mate of the level of battery life remaining.
Recalibration is required to maintain the specied
acuracy of the device. Replace the pre-calibrated sen-
sor module with a new one.
Note: you can do this yourself or send it to our Service
Centre for recalibration.
This indicates the number of tests performed since
the sensor was last calibrated.
This indicates the total number of tests performed
with the breathalyser since it was manufactured.
The breathalyser is unable to detect the sensor mod-
ule or there is a problem with the sensor module.
Contact AlcoLimit Breathalysers on 02 9939 3077.
The device is being used outside of its specied oper-
ating temperature of -50C to 400C.
System Error 1 or 2
Contact AlcoLimit Breathalysers on 02 9939 3077.
pg-10
WORKSafe©
AlcoLimit©
ACCESSING THE MENU
To access the MENU turn the breathalyser on by press-
ing the ON/OFF button then press the ‘M’ button (down
arrow on left hand side).
User PIN Code should appear on the display. If you hold
the button down too long then Administrator PIN Code
will appear. If so, press the up arrow and ON/OFF button
to restart.
Press the ON/OFF button once more then enter the PIN
code of 0000 by pressing the ON/OFF button 4 times.
The MENU CONTENTS are:
- Last tests
- Last maintenance
- Total test count
- Date & Time
- Measurement mode
- Set date
- Set time
- Set Language
- Backlight
- Printer
- Save to SD card
- Bluetooth
- Change user PIN
- Set Contrast
Navigating the menu
Use the UP and DOWN arrows to move up and down through the menu or menu
information.
Use the ON/OFF button to select a menu item.
Use the UP arrow to go backwards to a previous menu and press the ON/OFF button
to select the previous menu.
Note: If FAST MODE is set in the
main menu (see pg. 12) press the
down arrow when BLOW appears
on the display and you can enter
the User PIN Code entry screen.
Table des matières
Autres manuels AlcoLimit Équipement de test
Manuels Équipement de test populaires d'autres marques
SMART
SMART KANAAD SBT XTREME 3G Series Manuel utilisateur
Agilent Technologies
Agilent Technologies BERT Serial Manuel utilisateur
Agilent Technologies
Agilent Technologies N3280A Manuel utilisateur
Vernier
Vernier Go Direct Voltage Manuel utilisateur
Lifeloc
Lifeloc R.A.D.A.R. Manuel utilisateur
Fluke
Fluke T5-600 Instructions d'utilisation et d'installation
