Alcatel OmniAccess AP60 Manuel utilisateur

Access Point Enclosure Installation Instructions 1

Access Point Enclosure

Installation Instructions

The enclosure for the OmniAccess AP60, and AP61 Access Point

(OAW-AP60-ENCL) is an enclosure designed to provide protection

for APs when deployed in environments not suitable for

electronics components (dirt, moisture, etc). The enclosure does

NOT protect the AP against extreme high or low temperatures

and is not waterproof. The installer should refer to the appropriate

device Installation Guide for operational environmental

specifications. External mounting of the AP requires POE.

OmniAccess AP60 Enclosure Installation Notes: Installation Guide

2Part 031662-00 Rev. 01June 2005

Packing List

The OAW-AP60-ENCL includes:

Enclosure Housing base and top (11.75” (29.85cm) wide x 9” (22.86cm) deep x

3.5” (8.89cm) high)

Enclosure screws (6)

Ventilation cap, template, and screws (3)

Cable seal

Mounting plate (for the AP 60/61)

Mounting plate screws (2)—typically packed with cable seal

OAW-AP60-ENCL Installation Instructions (this guide, not pictured)

Access Point Enclosure Installation Instructions 3

Recommended tools

zPhillips head (#2) screw driver

zSharp knife

zDrill and bits for plastic - various sizes (depends on components supplied)

zCable tools for attaching cable connector

Preparing the Enclosure

1. To determine the best location for the cable seal and ventilation cap, lay

out the mounting plate with an AP aligned to the mounting plate tabs. The

illustration below shows placement of the seal on the bottom and the

ventilation cap on the side.

2. Remove the AP and the mounting plate.

CAUTION—Be sure to follow all tool safety instructions.

OmniAccess AP60 Enclosure Installation Notes: Installation Guide

4Part 031662-00 Rev. 01June 2005

3. Locate the cable seal on the bottom or side allowing for as direct a cable

path inside the enclosure as possible while preventing moisture from

entering the enclosure housing. (Here the cable seal is centered on the

bottom of the enclosure.)

4. Using a sharp knife, make an X cut on the top of the cable seal to allow the

network cable to penetrate the seal.

5. Measure the inside diameter of the cable seal base and drill the hole for the

cable seal. Any wood or metal high-speed or hole bit will work.

6. Snap the cable seal into place.

7. Drill the holes for the ventilation cap using the template (enclosed) as a drill

guide. Be sure to orient the ventilation cap to prevent moisture from

entering the enclosure housing.

8. Using the three screws provided, attach the ventilation cap.

9. Orient the mounting plate into position and attach to the enclosure base

with the two screws provided.

10. Push out the mounting tabs enough for the mounting holes on the back of

the AP to engage and snap the AP into place.

11. Using the four screw holes on the corners of the enclosure base, attach

the base in its external location.

12. Thread the raw network cable through the cable seal and into the

enclosure housing.

13. Attach the end connector (RJ-45).

14. Attach the cable connector to the AP (as described in the appropriate

Installation Guide).

15. Secure the enclosure cover with the six screws provided.

16. Secure the network cable from the enclosure to the WLAN switch. The

network cable must be POE-enabled to supply power to the Access Point.

17. Verify that the AP is functioning properly.

Autres manuels pour OmniAccess AP60

Table des matières

Autres manuels Alcatel Point d'accès sans fil

Alcatel

Alcatel OmniAccess OAW-AP65 Manuel utilisateur

Alcatel

Alcatel OmniAccess AP60 Manuel d'instructions d'installation

Alcatel

Alcatel ONETOUCH W600 Manuel utilisateur

Alcatel

Alcatel OAW-AP80M Manuel utilisateur

Alcatel

Alcatel OmniAccess AP70 Manuel utilisateur

Alcatel

Alcatel OmniAccess 1200R Manuel utilisateur

Alcatel

Alcatel OmniAccess OAW-AP70 Manuel utilisateur

Alcatel

Alcatel ONETOUCH Y580 Manuel utilisateur

Alcatel

Alcatel Lucent 300 Series Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur