Alarmtech MC 240-S45 Manuel utilisateur
MC 240-S45 Instruction Manual 4-MC240S45-01
©2013 Alarmtech Rev. MC240S45_1347en Page 1of 2
Detectors
Magnetic Contact
Surface mounting
Instruction Manual MC 240-S45
DESCRIPTION
MC 240-S45 is a heavy duty magnetic contact used in both
alarm and security access control systems for protection of
garage doors, industrial gates etc. against unauthorised
opening.
MC 240-S45 is certified according to EN 50131-2-6:2008.
MOUNTING INSTRUCTIONS
Contact and magnet should be installed in parallel,
corresponding to each other. Offset will reduce the
working distances.
The closer the contact/magnet is installed to the
ferromagnetic surface, the lower the working distances.
Magnetic contact should be installed in accordance
with the installation drawings.
CIRCUIT DIAGRAM
DISTANCE DIAGRAM - WOOD
TECHNICAL DATA
Working environment
Wood
Steel
Make distance
typ. 42 mm +/–40 %
not recommended
Break distance
typ. 50 mm +/–40 %
not recommended
Contact type
form A, SPST
Switching voltage max.
48 V DC/AC
Switching current max.
400 mA DC/peak AC
Contact rating max.
10 W
Estimated life expectancy
>20 million switching operations at 10 V/4 mA
Cable
6 m, ф 3,2 mm, 4x0,14 mm2
Sleeving
1 m, ф 8,2 mm, stainless steel
Environmental class (EN50130-5:2011)
IIIA
Operating temperature range
-40°C to +55°C
Operating humidity
max. 95% RH
Housing material
aluminium
Dimensions:
Contact part
73,5 x 15 x 25 mm
Magnet part
73,5 x 15 x 25 mm
Security grade (EN50131-2-6:2008)
2
Approvals
ITR 6/2013
0
10
20
30
40
50
60
-35 -25 -15 -5 515 25 35
y [mm]
x [mm]
Make distance Break distance
MC 240-S45 Instruction Manual 4-MC240S45-01
©2013 Alarmtech Rev. MC240S45_1347en Page 2of 2
OPERATING PRINCIPLE
MC 240-S45 magnetic contact has two parts: the contact
part with a reed switch and the magnet part. In its neutral
position the reed switch remains closed under the force of
the magnetic field. Opening the monitored object increases
the distance between the reed switch and the magnet. This
reduces the influence of the magnetic field on the reed
switch until it opens and activates an alarm.
Magnetic contacts should not be installed in the vicinity of
strong magnetic fields.
INSTALLATION
Depending on the application, contact and magnet should
be installed in one of the possible configurations. Installation
drawings show the correct positioning of the contact parts.
Contact and magnet should be installed in parallel, with
plastic plugs corresponding to each other. Offset will reduce
the working distances. The contact should be mounted on
the stationary part of the monitored object (ex. door frame)
and the magnet on the movable part (ex. door leaf).
For sites where it is impossible to mount the contact
directly, aluminium brackets and additional magnet parts are
available. Brackets can be used to mount the contact parts
away from a ferromagnetic surface or to solve problems
with aligning the contact with the magnet. Contact and/or
magnet should be screwed to the oval slots in the brackets
and adjusted to a suitable position.
Only non-ferromagnetic screws may be used for mounting
the contact.
After the installation, use an ohmmeter to check the
electrical connections and test the operation of the
magnetic contact.
Warning: installation in ferromagnetic environment is not
recommended.
INSTALLATION DRAWINGS
MC 240-S45 configurations:
MC 200-71 accessory:
RESISTORS (OPTIONAL)
MC 240-S45 is available in two additional options with
resistors of the chosen value: MC 240-S45-R with one
resistor parallel to the alarm switch and MC 240-S45-2R with
two resistors in 2 EOL configuration (see schematics below).
MC 240-S45-R:
MC 240-S45-2R:
DISTANCE TABLE
Contact
Accessory
Distance on wood [mm]
Distance on steel [mm]
Make
Break
Make
Break
MC 240-S45
-
42
50
X
X
MC 200-71
42
50
34a)
40a)
X –not recommended; a) measured with contact part installed 15 mm above the ferromagnetic surface (e. g. using MC L/MC Z
accessory)
We reserve the right to changes without notice.
Autres manuels Alarmtech Système de sécurité
Manuels Système de sécurité populaires d'autres marques
EDM
EDM Solution 6+6 Wireless-AE Manuel utilisateur
Highway Safety Group
Highway Safety Group EA401 Manuel utilisateur
Siren
Siren LED GSM Manuel utilisateur
Detection Systems
Detection Systems 7090i Instructions de montage
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuel utilisateur
Siemens
Siemens FDM273 Manuel utilisateur