Alarmcom ADC-W100 Manuel utilisateur

PoE to Wi-Fi Bridge (ADC-W100) - Installation Guide

There are two local options for connecting the W100 to the wireless network: Wi-Fi Protected Setup ( WPS) Mode or

Access Point (AP) Mode.

For information on how to install a video device via MobileTech, see Install a video device using the MobileTech app.

Note: The ADC-W100 is specifically designed for use with Alarm.com video cameras. Use with other devices is not

recommended.

Pre-installation checklist

• ADC-W100 PoE to Wi-Fi Bridge (included)

• Standard electrical outlet

• Broadband (Cable, DSL or Fiber Optic) Internet connection with router

• A computer, tablet or smartphone with Internet accessis required if the router does not have the Wi-Fi Protected

Setup (WPS) feature

• An Alarm.com Ethernet video camera with Ethernet cable

Connect the ADC-W100 to the wireless network using AP mode

Complete these steps to connect the W100 to the wireless network using AP Mode.

1. Plug the W100 into an electrical outlet that is within range of the customer’s Wi-Fi network. Wait for the Power LED

to turn solid green.

2. On an Internet-enabled device, connect to the wireless network “ADC_Bridge_XXX” where XXX is the last three

digits of the W100’s MAC address, which is located on the back of the W100.

3. On the same device, open a web browser and enter “http://w100install” in the URL field. Follow the on-screen

instructions to add the W100 to the wireless network. The WLAN LED will flash green when the connection is

complete.

4. Connect the PoE camera to the Camera port at the bottom of the W100 using an Ethernet cable.

5. Follow the installation instructions included with the camera to add it to an account.

Connect the ADC-W100 to the wireless network using WPS mode

Complete these steps to connect the W100 to the wireless network using WPS Mode.

1. Plug the W100 into an electrical outlet that is within range of the customer’s Wi-Fi network. Wait for the Power LED

to turn solid green.

2. Hold down the WPS button for about 3 seconds or until the WLAN LED begins to flash red.

https://answers.alarm.com/Installation_and_Troubleshooting/Video_Devices/PoE_to_Wi-Fi_Bridge_(ADC-W100)/PoE_to_Wi-Fi_Bridge_(ADC-W100)_-_Installation_Guide

Updated: Tue, 05 Jun 2018 19:55:53 GMT

3. Activate the WPS Mode on the router. The W100 will begin to connect to the wireless network. The WLAN LED will

flash green when the connection is complete.

4. Connect the PoE camera to the Camera port at the bottom of the W100 using an Ethernet cable.

5. Follow the installation instructions included with the camera to add it to an account.

Troubleshooting

• If you have issues connecting the W100 to the wireless network, power cycle the device and try again.

• If issues persist, try resetting the W100 to factory defaults by holding down the Reset button for 10 seconds, or until

the WLAN LED begins to flash red.

1. WPS Button

2. Reset Button

3. Power LED

4. WLAN LED

5. PoE Camera port, and Data port

Note: The data port can be used if the user would like to connect the W100 directly to the router instead of using

https://answers.alarm.com/Installation_and_Troubleshooting/Video_Devices/PoE_to_Wi-Fi_Bridge_(ADC-W100)/PoE_to_Wi-Fi_Bridge_(ADC-W100)_-_Installation_Guide

Updated: Tue, 05 Jun 2018 19:55:53 GMT

an Ethernet cable. Additionally, the Data port can act as a base station so an additional router or range extender

can be connected to this port.

https://answers.alarm.com/Installation_and_Troubleshooting/Video_Devices/PoE_to_Wi-Fi_Bridge_(ADC-W100)/PoE_to_Wi-Fi_Bridge_(ADC-W100)_-_Installation_Guide

Updated: Tue, 05 Jun 2018 19:55:53 GMT

LED guide

https://answers.alarm.com/Installation_and_Troubleshooting/Video_Devices/PoE_to_Wi-Fi_Bridge_(ADC-W100)/PoE_to_Wi-Fi_Bridge_(ADC-W100)_-_Installation_Guide

Updated: Tue, 05 Jun 2018 19:55:53 GMT

LED label LED status color Description

No light Power off

Power

Solid Green Power on

No light Wi-Fi not in use

Solid Green Wi-Fi connected

Green blink Data is being sent over

Wi-Fi

Solid Red Wi-Fi connecting or

connection failed

Red blink WPS pairing process

Amber blink Weak Wi-Fi signal

WLAN

Red + green Poor Wi-Fi connectivity

No light No data transmission on

the Data port

Data

Green blink Data is being sent over the

Data port

Camera No light No camera detected on

the Camera port

https://answers.alarm.com/Installation_and_Troubleshooting/Video_Devices/PoE_to_Wi-Fi_Bridge_(ADC-W100)/PoE_to_Wi-Fi_Bridge_(ADC-W100)_-_Installation_Guide

Updated: Tue, 05 Jun 2018 19:55:53 GMT

Green blink

Camera is connected to

the Camera port

Note: It is common to see

the Camera LED go

between a solid green and

a quick rapid flicker/blink.

This is expected behavior.

Questions?

For further questions, create a support ticket using the Support Center, or call Alarm.com CORE Technical Support.

https://answers.alarm.com/Installation_and_Troubleshooting/Video_Devices/PoE_to_Wi-Fi_Bridge_(ADC-W100)/PoE_to_Wi-Fi_Bridge_(ADC-W100)_-_Installation_Guide

Updated: Tue, 05 Jun 2018 19:55:53 GMT

Table des matières

Autres manuels Alarmcom Point d'accès sans fil