Alarmcom ADC-V821 Manuel utilisateur
INSTALLATION GUIDE
ADCV821
INDOOR/OUTDOOR
MINI DOME
CAMERA
ADC-V821 Installation Guide 1
Pre-Setup Checklist
• ADC-V821 camera
(included)
• AC power adapter
(included; required for non-PoE connections)
• Broadband (Cable, DSL, or Fiber Optic)
Internet connection with router
• A computer or mobile device with Internet access
• An Ethernet / Cat5 cable
• Login and Password for the Alarm.com account
to which you will add the camera
2ADC-V821 Installation Guide ADC-V821 Installation Guide 3
Add the Camera to an
Alarm.com Account
Complete these steps prior to installing the camera
in its final location:
1Connect the camera to the router via an Ethernet cable
2If the Ethernet connection does not provide power,
connect the camera to an AC power adapter and plug
the adapter into a non-switched outlet.
3Wait 2 minutes for the camera to connect
to the Internet.
4Add the device by either selecting the account in
MobileTech OR by using a web browser and entering the
following URL: www.alarm.com/addcamera
5Select the camera from the video list or type in its MAC
address to begin adding the camera. The camera’s MAC
address is located on the base of the camera.
6Follow the on-screen instructions to finish adding the
camera. You may configure camera settings from the
Customer Website.
You can now power down the camera and install it in its
final location using the included hardware.
4ADC-V821 Installation Guide ADC-V821 Installation Guide 5
Troubleshooting
• If you have issues connecting the camera to the account,
power cycle the camera and try again.
• If issues persist, try resetting the camera to factory
defaults by using the Reset button (located under the
camera cover).
- Ensure the camera is connected to a power supply.
- Unscrew and remove the camera cover, being careful
to not damage the connecting wires.
- Press and hold the Reset button for 6 seconds or until
the IR LEDs flash red.
Dome Cover
Reset Button
Bottom Case
Light Sensor
Tilt Stopper Screw
Gimbal
RJ-45 Cable
DC Power Cable
IR LEDs
Lens
ADC-V821 Installation Guide 7
5Secure the two mount bolts into the camera’s bottom.
6Insert the mount bolts into the template holes.
7Affix the camera to the mounting surface by tightening
the mount nuts to the mount bolts on the ceiling panel.
6ADC-V821 Installation Guide
Install the Camera
1Choose a flat, sturdy location to mount the camera.
2Remove the dome cover using the provided torx wrench.
3Use the included mounting template to drill the
mounting and cable holes. If you are installing on a hard
ceiling or wall, only drill the cable hole.
4Connect the Ethernet cable to the camera by feeding
the cable through the appropriate hole. If required,
connect the power cable. If you are installing on a hard
ceiling or wall, skip to Step 8.
Power
Ethernet
Cable
Ethernet
Cable
8ADC-V821 Installation Guide ADC-V821 Installation Guide 9
8For hard ceiling and wall installations only: Attach the
base of the camera to the mounting location using the
included screws.
9Rotate the camera gimbal as shown in the image to
achieve the desired viewing angle. Loosening the tilt
stopper screw (using a PH000 screwdriver) can make
this process easier.
Warning: Do not tilt the camera beyond 70 degrees.
10 Re-attach the dome cover using the provided
torx wrench.
Warning: Ensure that the light sensor (see camera
diagram) is visible when the camera cover is attached.
If the light sensor is shielded by the cover, the camera
will always be in night mode.
11 Remove the protective film from the dome cover.
Gimbal
70° Max
Template Sheet
10 ADC-V821 Installation Guide ADC-V821 Installation Guide 11
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Disposal of Old Appliance
1. When this crossed-out wheel bin symbol is attached to a product it means the product is covered by the
European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the municipal waste stream
in accordance to laws designated by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for the
environment and human health.
4. For more detailed information about disposal of your old appliance, please contact your city office,
waste disposal service or the shop where you purchased the product.
Notes
12 ADC-V821 Installation Guide
Notes
© 2017 Alarm.com. All rights reserved.
8281 Greensboro Drive, Suite 100
Tysons, VA 22102 170518
Table des matières
Autres manuels Alarmcom Caméra de sécurité
Alarmcom
Alarmcom ADC-VDB101 Manuel utilisateur
Alarmcom
Alarmcom ADC-V720W Manuel utilisateur
Alarmcom
Alarmcom Pro Series Manuel utilisateur
Alarmcom
Alarmcom ADC-CSVR2000P Manuel utilisateur
Alarmcom
Alarmcom ADC-V515 Manuel utilisateur
Alarmcom
Alarmcom ADC-VC726 Manuel utilisateur
Alarmcom
Alarmcom ADC-VC736 Manuel utilisateur
Alarmcom
Alarmcom ADC-VC836 Manuel utilisateur
Alarmcom
Alarmcom Knowledge Base ADC-VC826 Manuel utilisateur
Alarmcom
Alarmcom Wellcam ADC-V622-WELL Manuel utilisateur
Alarmcom
Alarmcom ADC-VC726 Manuel utilisateur
Alarmcom
Alarmcom ADC-V723 Manuel utilisateur
Alarmcom
Alarmcom ADC-V724 Manuel utilisateur
Alarmcom
Alarmcom ADC-VC836 Manuel utilisateur
Alarmcom
Alarmcom ADC-VC825 Manuel utilisateur
Alarmcom
Alarmcom ADC-VC726 Manuel utilisateur
Alarmcom
Alarmcom ADC-V515 Manuel utilisateur
Alarmcom
Alarmcom ADC-VC826 Manuel utilisateur
Alarmcom
Alarmcom ADC-VC727P Manuel utilisateur
Alarmcom
Alarmcom ADC-VC725 Manuel utilisateur
