2
ALARM LOCK SYSTEMS, INC. (ALARM LOCK) warrants its products to be free from manufacturing
defects in materials and workmanship for 24 months following the date of manufacture. ALARM LOCK
will, within said period, at its option, repair or replace any product failing to operate correctly without
charge to the original purchaser or user.
This warranty shall not apply to any equipment, or any part thereof, which has been repaired by
others, improperly installed, improperly used, abused, altered, damaged, subjected to acts of God, or
on which any serial numbers have been altered, defaced or removed. Seller will not be responsible for
any dismantling or reinstallation charges.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF. THERE IS NO EXPRESS OR IMPLIED WARRANTY OF
MERCHANTABILITY OR A WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
ADDITIONALLY, THIS WARRANTY IS IN LIEU OF ALL OTHER OBLIGATIONS OR LIABILITIES
ON THE PART OF ALARM LOCK.
Any action for breach of warranty, including but not limited to any implied warranty of merchantability,
must be brought within the six months following the end of the warranty period. IN NO CASE SHALL
ALARM LOCK BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN
IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT.
In case of defect, contact the security professional who installed and maintains your security system.
In order to exercise the warranty, the product must be returned by the security professional, shipping
costs prepaid and insured to ALARM LOCK. After repair or replacement, ALARM LOCK assumes the
cost of returning products under warranty. ALARM LOCK shall have no obligation under this warranty,
or otherwise, if the product has been repaired by others, improperly installed, improperly used, abused,
altered, damaged, subjected to accident, nuisance, flood, fire or acts of God, or on which any serial
numbers have been altered, defaced or removed. ALARM LOCK will not be responsible for any
dismantling, reassembly or reinstallation charges.
This warranty contains the entire warranty. It is the sole warranty and any prior agreements or
representations, whether oral or written, are either merged herein or are expressly canceled. ALARM
LOCK neither assumes, nor authorizes any other person purporting to act on its behalf to modify, to
change, or to assume for it, any other warranty or liability concerning its products.
In no event shall ALARM LOCK be liable for an amount in excess of ALARM LOCK's original selling
price of the product, for any loss or damage, whether direct, indirect, incidental, consequential, or
otherwise arising out of any failure of the product. Seller's warranty, as hereinabove set forth, shall not
be enlarged, diminished or affected by and no obligation or liability shall arise or grow out of Seller's
rendering of technical advice or service in connection with Buyer's order of the goods furnished
hereunder.
ALARM LOCK RECOMMENDS THAT THE ENTIRE SYSTEM BE COMPLETELY TESTED
WEEKLY.
Warning: Despite frequent testing, and due to, but not limited to, any or all of the following; criminal
tampering, electrical or communications disruption, it is possible for the system to fail to perform as
expected. ALARM LOCK does not represent that the product/system may not be compromised or
circumvented; or that the product or system will prevent any personal injury or property loss by
burglary, robbery, fire or otherwise; nor that the product or system will in all cases provide adequate
warning or protection. A properly installed and maintained alarm may only reduce risk of burglary,
robbery, fire or otherwise but it is not insurance or a guarantee that these events will not occur.
CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY,
PROPERTY DAMAGE, OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE
WARNING. Therefore, the installer should in turn advise the consumer to take any and all precautions
for his or her safety including, but not limited to, fleeing the premises and calling police or fire
department, in order to mitigate the possibilities of harm and/or damage.
ALARM LOCK is not an insurer of either the property or safety of the user's family or employees, and
limits its liability for any loss or damage including incidental or consequential damages to ALARM
LOCK's original selling price of the product regardless of the cause of such loss or damage.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the
exclusion or limitation of incidental or consequential damages, or differentiate in their treatment of
limitations of liability for ordinary or gross negligence, so the above limitations or exclusions may not
apply to you. This Warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
ALARM LOCK LIMITED WARRANTY
THE FOLLOWING STATEMENT IS REQUIRED BY THE FCC.
This equipment generates and uses radio-frequency energy and, if not installed and used
properly, that is, in strict accordance with the manufacturer's instructions, may cause
interference to radio and television reception. It has been type tested and found to comply with
the limits for a Class-B computing device in accordance with the specifications in Subpart J of
Part 15 of FCC Rules, which are designed to provide reasonable protection against such
interference in a residential installation.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures: reorient the receiving antenna; relocate the computer
with respect to the receiver; move the computer away from the receiver; plug the computer into
a different outlet so that computer and receiver are on different branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for
additional suggestions. The user may find the following booklet prepared by the Federal
Communications Commission helpful: “How to Identify and Resolve Radio-TV Interference
Problems”. This booklet is available from the U.S. Government Printing Office, Washington, DC
20402; Stock No. 004-000-00345-4.
above. When the locking device unlocks and relocks,
the testing process ends and "normal" Networx system
operation resumes. Note: During normal operation,
the locking device is designed to always open on the
first button press (no need to "press and hold"; one
press is sufficient).
CLEARING A WIRELESS REMOTE
For a Wireless Remote paired to a locking device, this proce-
dure essentially "un-pairs" and restores a Wireless Remote to
its default settings.
1. Unscrew all 4 rear screws on the Wireless Remote to
detach the back cover.
2. Remove the circuit board and use a pencil to push the
battery (CR2450 button cell) from its holder.
3. Press and hold the Wireless Remote button. Keep
holding the button and slide the button cell back into its
holder (positive (+) side up); continue holding the button.
4. While holding the button, wait until the LED rapidly tog-
gles between red and green ("red-green-red-green" con-
tinuously), then release the button.
5. Replace the PC board, attach the rear cover and replace
the 4 rear screws. Test the Remote.
The Wireless Remote will be "un-paired" with the locking de-
vice, and will be available for future pairing. Note: This pro-
cedure is not required to allow a previously paired remote to
be paired with a new locking device; simply pair the remote
with the new locking device as per the "PAIRING PROCE-
DURE" on page 1 and the first pairing will be erased.
CLEARING A LOCKING DEVICE
Up to ten (10) Wireless Remotes can be simultaneously
paired with one individual Networx locking device. Use Func-
tion 64 to remove all paired Wireless Remotes from a single
locking device:
1. At the locking device keypad, enter Program Mode
(press the Master Code and press ;).
2. Press the following: ;64:
Note: Function 64 will disable all hardwired remote re-
lease ("Remote Input") switches, if present. In addition, if
a Wireless Remote is misplaced or stolen, ALL Wireless
Remotes must be removed from the locking device to en-
sure system security.
3. Exit Program Mode: Press and hold any key until a se-
ries of beeps is heard.
LOW BATTERY INDICATION
During normal operation, when the Wireless Remote button is
pressed and its battery is weak, its LED will flash red-green re-
peatedly for several seconds. Always replace a weak battery as
soon as possible. Use one 3V lithium type CR2450 button cell
only. Replace Cell: Unscrew all 4 rear screws, detach the
back cover, remove circuit board and use pencil to push the but-
ton cell from its holder. Slide a new cell into its holder (positive
(+) side up). Replace the PC board, attach the rear cover and
replace the 4 rear screws. Test the Remote.
REPLACING A LOCKING DEVICE
If the paired locking device is physically replaced with a new
locking device, the "PAIRING PROCEDURE" must be repeated
with each Wireless Remote.
