Akyga AK-CA-73 Manuel utilisateur
AK-CA-73 - user manual
/ak-ca-73
www.akyga.com
Short description of the product
The product is compatible with the applicable national and European requirements.
What is in the box?
- AK-CA-73 Controller
- Molex / JST-PH 4-pin cord
- Remote control
Symbols explanation:
There is a risk of losing health or life (e.g. by electic shock).
There is a particular danger connected with service.
Important tips and information.
Product accordance with the EU directive 2002/96/EC. The symbol of the crossed out basket
placed on the product means that the marked product can not be disposed of with other
household waste. After use, the product must be return to collection point for used electical and
electronic equipment or to the seller. Appropriate segregation of rubbish for subsequent
processing, recovery or descrution contributes to avoiding negative effects on the environment
and health, and also allows the recovery of raw materials from which the product is made.
p. 1
The CE standard description on the product is the manufacturer's declaration that the marked
product meets the requirements of the directive so-called The "New Approach" of the European
Union (EU). For security and certification (CE) reasons, the device can not be rebuild or change in
any way. In the reason of using the power supply for other purposes than those described, the
product may be demaged. The incorrect use may also cause hazard such as short-circuits,
burns, electric shocks, etc. Read the users manual carefully and keep it for later use. The product
could be share to third partie only with the user manual included.
The Akyga AK-CA-73 controller is used to control up to ten fans and two LED strips. Control is carried out
using the included remote control, which allows you to select visual effects and change the operating
parameters of fans according to individual needs. In addition, the controller is compatible with JST 6-pin
fans and LED strips with JST 4-pin connectors.
The product is designed for a DC voltage of 5 V/12 V from the Molex socket of an ATX power supply. The
current consumption of the supplied devices must not exceed the current indicated on the controller.
LED fan controller
Ecological Solutions
GREEN
RF 433,92 MHz
AK-CA-73 - user manual
p. 2
Safety Precautions
Connecting computer components whose demanded power is greather than power of the controller,
can cause damage (burn) of controller.
An electrostatic discharge occurs when two object touch each other, for example, an electric
charge that occurs when user touch metal door handle after walking on a carpet. Discharging
electrostatic charges from fingers or other electrostatic conductors can damage electronic
components. To avoid damaging the controller or devices connected to it, abstain from touching
contacts, wires and electonic circuits. The user’s contact with electronic components should be
kept to a minimum.
The manufacturer of the product is not responsible for damage or insults caused in effect
of disobey the safety instructions and informations contained in these user manual.
źThe product operation in adverse conditions is not allowed. Adverse conditions are primarily:
exposure to direct sunlight, high or very low ambient temperatures, strong vibrations, high
humidity, surrounds of gases, dusts or flammable and aggressive liquids.
źShort-circuiting the current connection is prohibited.
źKeep the product and the packaging out of range of children and animals. The package
includes a foil that child could choke while playing.
źIt is forbidden to apply the mechanical load to the product - strong shocks, impacts, dropping or
crushing may cause its damage.
źProduct and power cord should not be touched with moist or wet hands under no
circumstances.
źTake account of the user manual for other devices connected to the adapter.
źMake sure that the power cord is not crushed, bent, twisted, rubbed against sharp edges or
mechanically loaded in any other way. Avoid thermal load of the cable - in particular keep away
from heat sources (such as stoves, radiators, fireplaces).
źBefore connecting the adapter to the power supply, make sure that the power of the adapter is
sufficient for the components in the computer.
źIf the product has been damaged, does not work properly or has been stored for a long period
of time in bad or unfavorable conditions, safe operation of the device is not possible. It is
essential to stop using the product and to protect it against re-use for security purposes.
źIt is not allowed to put any objects inside the controller.
źThe controller is connected to the power by plugging it into the Molex connector of an ATX
power supply unit providing 5 V/12 V DC.
LED fan controller
The controller should work in internal conditions that do not cause contact with water and direct
sunlight.
During operation, the controller should be located in a designated housing.
The RoHS mark on the product is the manufacturer's declaration that the marked product meets
the requirements of the EU Restriction of Hazardous Substances (2002/95/EC) directive, which
aims to reduce the amount of hazardous substances penetrating into the environment from
electrical and electronic waste.
The device is intended only for domestic use, indoors.
AK-CA-73 - user manual
p. 3
LED fan controller
Problem
Cause
Solution
Controller or
components connected
to it do not function
correctly
No mains voltage
źCheck the correct connection of
the power supply to the power
network
źCheck the mains fuses
LED backlight off
źActivate the LED backlight in
the fans/strips using the remote
control
Incorrect connection of
the device
ź Check that the wires are well
embedded in the sockets
ź Make sure that the plugs are
correctly connected to the
controller
There is a suspicion of a
product defect
źStop using and contact the
seller
Fans do not react to
changing settings
Offloaded battery in
remote control
źReplace the battery in remote
control
Too much distance
between the remote
control and the controller
źBring the remote control closer
to the controller
źStop using and contact the
seller
There is a suspicion of a
product defect
Removing the most common problems
źBefore connecting or conservation of the adapter make sure that the power cords are not live.
źIn case of any doubts regarding operation, safety or connection of the product, please contact
the manufacturer or a qualified specialist for this purpose.
źAll maintenance, adjustment and repair work on the product may only be carried out by a
qualified person in a specialist facility.
źFirst connect controller to computer components then connect controller to AC/DC power
adapter. Never the other way around.
AK-CA-73 - user manual
p. 4
LED fan controller
Connecting fans and LED strips to the controller
2. Make sure that the controller is not connected to a power source.
3. Select and connect the appropriate 6-pin plug from the fan to the 6-pin socket on the controller.
1. Make sure that the current consumption of the fans and LED strips does not esceed the
maximum allowable load for the controller.
4. Connect up to two LED strips with the corresponding 4-pin connectors to the 4-pin sockets of
LED STRIP 1 and/or LED STRIP 2.
Connecting controller to power supply
2. Connect cable included in the kit. The 4-pin connector should be plugged into the POWER
socket in the controller. The Molex connector should be plugged into the corresponding socket
on the ATX power supply.
3. Optional: connect the 2-pin SW button connector from the case front panel to the 2-pin
connector on the controller.
1. Make sure that the power supply is disconnected from power source.
5. Attach the controller to the chosen location in the case.
4. Peel off the strip securing the double-sided tape on the back of the controller.
6. The controller is ready to use.
Rekomended:
Akyga AW-12D-RGB
SUPPLY FROM
MOLEX SOCKET RGB LED Strip
5V 4 pin
POWER SW
MAIN BOARD
OPTIONAL
SW
AK-CA-73 - user manual
p. 5
LED fan controller
Remote control
2. Off – Turn on the LED illumination.
1. On – Turn on the LED illumination.
3. Auto mode – Switch automatic illumination program.
5. S- – reduce the speed of the fans.
6. M+ – Select next illumination program.
10. Select LED backlight colour.
The controller has a built-in memory. When the power is switched on again, the previous illumination
will be displayed.
8. Increase LED brightness.
4. S+ – increase the speed of the fans.
7. M- – Go back to the previous illumination mode.
9. Reduce LED brightness.
3
12
4
5
6
8
9
7
10
AK-CA-73 - user manual
p. 6
LED fan controller
Product manufacturer: Ropla Computers sp. z o.o.
ul. Wrocławska 1c
52-200 Suchy Dwór
Technical specfication
Product code:
Supply voltage:
Maximum power:
Output voltage:
Maximum energy load:
Temperature:
Fan adjustments:
Cable length:
The cable plug 1:
The cable plug 2:
Remote control power supply:
Frequency band of the remote control:
Included accesories:
Compilance with standards:
REACH compatibility:
EAN code :
AK-CA-73
Molex 12 V/5 V
Max. 10 A
12 V for Fan, 5 V for LED
4,8 A (max. 0,4 A for fan/LED strip)
5-60ºC
Yes
28 cm
Molex
JST-PH 4-pin
CR2025 Battery
RF 433.92 MHz
LED Remote control
CE, RoHS
YES
5901720136084
Cleaning the power supply:
źUse soft and antistatic cloth for cleaning the controller.
źDo not use abrasive or chemical cleaners.
Disconect the controller from the electrical socket and connected devices before cleaning.
Table des matières
Autres manuels Akyga Contrôleurs
