Akron SAM BOOST Manuel utilisateur

SAM BOOST™ WITH

SMART NOZZLE N2P

QUICK START GUIDE

SAM BOOST™ SYSTEM

FULLY INSTALLED WITHOUT

ANTENNA & WATER TANK

LEVEL SENSOR

SAM BOOST™ WITH SMART NOZZLE N2P

QUICK START GUIDE

Refer to FSG-MNL-00232 for complete listing of Safety Hazards & Warnings

Sheet: FSG-MNL-00233

Revision 7 / 10 / 2023

Page: 1 of 7

Box #1 –SAM BOOST™ Electronic Components

SAM BOOST™ WITH SMART NOZZLE N2P

QUICK START GUIDE

Refer to FSG-MNL-00232 for complete listing of Safety Hazards & Warnings

Sheet: FSG-MNL-00233

Revision 7 / 10 / 2023

Page: 2 of 7

Box #2 –SAM BOOST™ Valves & Venting Components

SAM BOOST™ WITH SMART NOZZLE N2P

QUICK START GUIDE

Refer to FSG-MNL-00232 for complete listing of Safety Hazards & Warnings

Sheet: FSG-MNL-00233

Revision 7 / 10 / 2023

Page: 3 of 7

1. WHAT’S INCLUDED

1.1 Box #1 –SAM BOOST™ Electronic Components

A. Batteries & Battery Chargers

B. Wireless CAN Module & Antenna

C. Matrix Module

D. SAM BOOST™ System Harness

E. Cross Pump Backbone Harness with CAN Hubs

F. SAM BOOST™ Display, Display Labels, Power Module, & Adapter Plate

G. Alarm Buzzer (Optional)

H. Master Intake & Master Discharge Pressure Sensors

I. Caution Labels & Push-Pull Cover Placards

1.2 Box #2 –SAM BOOST™ Valves & Venting Components

a. 2” Preconnect Boost Valves, Pressure Sensors, & Valve Harnesses

b. Tank-to-Pump Boost Valve & Valve Harness

•Customer Specified, 3” or 4” Valve Size Available

c. Pump Venting Solenoid & Fittings

d. Water Tank Level Sensor & Fittings

e. Nozzle Color Handle Kit

2. PREPLAN INSTALLATION

□Find optimal location for Antenna within 8’ of Wire to Wireless CAN Module

□Lay out all components included in kit on pump as shown in System Layout

□Verify harnesses are within reach of components

3. VALVE INSTALLATION

□Remove Original Valve Components (Controls, drains, etc.)

□Install Boost Valves

•May require rotating electric actuators for clearance. If valve is rotated then

position sensor calibration (password 08266) must be performed

□Install Pressure Sensor into Drain Line or Gauge Line near Valve

□Connect Harnesses to Valve Electric Actuator

•Point Electrical Connection Ports down or sideways to avoid water intrusion

SAM BOOST™ WITH SMART NOZZLE N2P

QUICK START GUIDE

Refer to FSG-MNL-00232 for complete listing of Safety Hazards & Warnings

Sheet: FSG-MNL-00233

Revision 7 / 10 / 2023

Page: 4 of 7

4. DISPLAY INSTALLATION

□Remove Original Equipment Pressure Governor

□Mount SAM BOOST™ Display with Adapter Plate

□Replace Original Equipment Master Intake & Discharge Pressure Sensors

If Buzzer Included in Kit:

□Remove Original Equipment Buzzer

□Install SAM BOOST™ Display Buzzer

If Buzzer NOT Included in Kit:

□Connect Buzzer into SAM BOOST™ Display

5. WATER TANK COMPONENT INSTALLATION

□Install Pump Venting Solenoid to 1/4” NPT Port on Discharge Side of Pump

□Install Check Valve Assembly to Water Tank or Discharge Side of Tank Fill Valve

□Connect & Route 3/8” Push-On Hose Tubing between Solenoid & Check Valve

□Locate & Remove OEM Water Tank Sensor

□Install OEM Water Tank Sensor to SAM BOOST™ Tank Assembly

□Install SAM BOOST™ Tank Assembly to Water Tank

6. ELECTRONIC MODULE INSTALLATION

□Mount Matrix & Radio Modules to Valves

•Adapter fits 2.5”, 3”, or 4” Valves

7. HARNESS INSTALLATION

□Connect all Harnesses shown on System Layout

□Connect OEM Power & Ground to SAM BOOST™ Power & Ground

•Do NOT wire to circuit with heavy motor loads (such as primer, foam system)

•Wire to switched power source with 60 AMP protection on positive (+) side

8. WARNING LABEL & PLACARD INSTALLATION

□Locate & Place Warning Labels where Preconnect Hoses are Deployed

□Locate & Place Cover Placards over Original Valve Control Push Rods Panel Holes

SAM BOOST™ WITH SMART NOZZLE N2P

QUICK START GUIDE

Refer to FSG-MNL-00232 for complete listing of Safety Hazards & Warnings

Sheet: FSG-MNL-00233

Revision 7 / 10 / 2023

Page: 5 of 7

9. SOFTWARE QUICKSTART

□Assign SAM BOOST™ Display UI Layout (Password: 14000)

□Calibrate Water Tank Level Sensor (Password: 08265)

1. Fill Water Tank & Hit Button above Full icon

2. Empty Water Tank & Hit Button below the Empty icon

3. Hit Enter when complete to save

□Verify Nozzle Names & Colors on Home Page

•If incorrect, change on password 00401 page

▪Valve 1 is valve associated with top left icon of the screen

▪Valve 2 is valve associated with top right icon of the screen

SAM BOOST™ WITH SMART NOZZLE N2P

QUICK START GUIDE

Refer to FSG-MNL-00232 for complete listing of Safety Hazards & Warnings

Sheet: FSG-MNL-00233

Revision 7 / 10 / 2023

Page: 6 of 7

□Calibrate Nozzle Preset (Password: 10610)

Nozzle Preset Calibration will open discharge valve associated

with nozzle and automatically increase line pressure.

Calibration must be performed with two people

1. Engage Pump while inside Calibration Screen

2. Wake up Nozzle by Pressing 1 Button

3. Follow Instructions on Display

4. Press START 1 or START 2 to Calibrate Nozzle 1 or 2

5. Valve will open and line pressure will automatically increase until nozzle

meets desired pressure message

•Verify that Nozzle Bail is Fully Open when calibrating

6. The calibration process will automatically stop & close line when nozzle

pressure is reached

SAM BOOST™ WITH SMART NOZZLE N2P

QUICK START GUIDE

Refer to FSG-MNL-00232 for complete listing of Safety Hazards & Warnings

Sheet: FSG-MNL-00233

Revision 7 / 10 / 2023

Page: 7 of 7

10.FINAL COMMISSIONING CHECKLIST

INITIAL

PASS

CRITERIA

□

Verify Display shows SAM BOOST™ Splash screen while Pump in Road

Mode & Transmission in Drive Gear with Two People for Safety

□

Operate Preconnect Valves from Display - Full Open and Full Close

(Not required to be in Pump Gear)

□

Operate Tank-to-Pump Valve from Display - Full Open and Full Close

(Not required to be in Pump Gear)

□

Put into Pump Gear and verify no Warnings appear

□

Increase and Decrease Engine RPM with the Display

(If unable to do so, verify Governor Settings [Password: 00311])

□

Verify Emergency Idle functions with the Display

Press Mode button to revert to PSI Mode

□

While in PSI Mode, Increase Set Pressure to 100 PSI (or value that

increases Engine RPM.) Verify that Pump Set Pressure on Display

matches Master Discharge Gauge Pressure

□

Operate Nozzles to Open the Paired Preconnect Valves

□

With Two People for Safety, Validate Nozzle Calibration is correct by

having one person hold the bail Full Open & the other person at the

display checking Actual Pressure equals Rated Pressure with Full Hose

Length by pressing the Info Button on valve page

□

Validate Nozzle Signal Strength is reading appropriately. This can be

checked by pressing the info button on the valve page

□

Validate Truck voltage is reading appropriately. This can be checked by

pressing the info button on the valve page

(If incorrect, adjust on 06565 password page)

□

Drain tank while in Tank Mode and trip low tank warning audio & visual.

Warning should trip at ¼ tank level

(Validate buzzer operation and tank calibration)

□

Apply hydrant pressure, close tank-to-pump, and validate that nozzle

changes to a blue color

□

Check Engine Oil Pressure & Temperature

Table des matières

Autres manuels Akron Équipement de lutte contre l'incendie

Akron

Akron 3578 STREAMMASTER Instructions de montage

Akron

Akron 3462 Manuel utilisateur

Manuels Équipement de lutte contre l'incendie populaires d'autres marques

Tyco Fire Protection Products

Tyco Fire Protection Products AM31 AQUAMIST Nozzle Manuel utilisateur

Task Force Tips

Task Force Tips Extend-A-Gun RC3 Manuel du propriétaire

Autronica

Autronica AutroSafe BSD-321/EX Manuel utilisateur

POK

POK Froggy Manuel utilisateur

Waterous

Waterous AQUIS Series Manuel

CTP

CTP NPO ETERNIS GUARANT-7 Manuel de la liste des pièces

MSA

MSA M1 Manuel utilisateur

Grundfos

Grundfos Hydro EN Manuel d'utilisation

Amerex

Amerex 570 Guide d'application

Vimpex

Vimpex BIG HP18-H200-B1 Manuel utilisateur

Global Fire Equipment

Global Fire Equipment GFE-PA-VOX-A Manuel utilisateur

Chubb

Chubb PEFS F3 Manuel utilisateur

Projoy Electric

Projoy Electric PEFS-PL Series Manuel utilisateur

klimaoprema

klimaoprema FDC25 Series Manuel utilisateur

Tyco

Tyco 802SB Manuel utilisateur

Mueller

Mueller Revive M2 Manuel utilisateur

SEI Industries

SEI Industries BAMBI MAX BBXHL4000PF Manuel utilisateur

Waterax

Waterax MARK-3 Manuel utilisateur