AJA D10AD Manuel utilisateur

D10AD

10-bit Analog to SDI

Converter

User Manual

September 2, 2005 P/N 101639-00

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - FAX 781.665.0780 - TestEquipmentDepot.com

AJA D10AD 10-bit Component/Composite to SDI Converter User Manual — Introduction

Introduction

The D10AD provides excellent quality 10-bit conversion of component or

composite analog video to SDI—with EDH. The D10AD accepts YPbPr (SMPTE,

EBU-N10), Betacam, or RGB component inputs and NTSC/PAL or YC (S-Video)

composite inputs. When using composite sources, the D10AD offers a 4-Line

Adaptive Comb Filter for high quality decoding. The comb ﬁlter can be switched to

2-line or notch modes for minimum delay requirements. NTSC/PAL conﬁguration

is automatic. Video format, AGC, H/V blanking, and pedestal are all user

conﬁgurable via dipswitches.

Note:

The D10AD requires a Time Base Correct source. Operation is not

recommended from VTRs, laser disks, etc., without Time Base Correction (TBC).

Features

•

Excellent-Quality 10-bit Universal A/D Conversion

•

Component, Composite or Y/C Analog Input

•

4-Line Adaptive Comb Filter

•

Full 10-bit Data path, 2x Oversampling

•

YPbPr, Betacam, or RGB Component Formats

•

Composite NTSC or PAL

•

AGC mode

•

4 SDI outputs with EDH

•

Color Bar Generator

•

External DIP switch user interface for configuration

Block Diagram

D10AD 10-bit Analog Component and Composite to SDI Converter, Block

Diagram

DIP

Switch

User

Interface

for

Feature

Selection

10-bit A/D

Converter

Sync

Lock

Comb

Filter

Serial Video Out 1

Serial Video Out 2

Serial Video Out 3

Serial Video Out 4

COMPONENT/COMPOSITE

INPUTS (selected by DIP switch)

COMP

I/O Connections

D10AD, Side View

User Controls

The user interface for the D10AD is an 8-

switch DIP accessible through a cut-out in the

bottom of the unit. Use the DIP switches to

conﬁgure outputs, pedestal, blanking, and

enable or disable comb ﬁlter, EDH, AGC, and

test pattern.

Switches 1 and 2 select composite or

component input and the type of component

input. Switches 3 through 8 set conﬁguration

features. The exact function of each DIP

switch and what it controls is described on the

following pages.

Note:

Changing input format (SW1, SW2, or SW3) causes a reset to occur that

takes about 10 seconds to complete.

+ 5VDC

Power

Input

Serial

Digital

Outputs

4 BNCs

Composite/

Component

Inputs

Conﬁguration

determined by

DIP switch on

other side of

Converter

DIP Switches

OFF ON

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - FAX 781.665.0780 - TestEquipmentDepot.com

AJA D10AD 10-bit Component/Composite to SDI Converter User Manual — User Controls

Switch 1—Selects Component or Composite input from the Compos-

ite/Component BNCs

Switch 2—Configure Type of Component input from the Composite/

Component BNCs

Switch 3—Configure Pedestal For Output BNCs (disabled in PAL)

Switch 4—Configure Blanking—Not Currently Implemented

The convertor defaults to narrow blanking.

Switch 5—Turn Comb Filter ON or OFF

Switch 6—Configure EDH Insertion

ON OFF

Selects Composite input. Selects Component input.

ON OFF

RGB Input (If SW1 is OFF) or Composite

Input (If SW 1 is ON).

YPbPr Input (If SW1 is OFF) or

Y/C (S-VIDEO) (If SW1 is ON().

ON OFF

If set for COMPOSITE Input:

Pedestal is removed on inputs with 7.5 IRE

Pedestal

If set for COMPONENT Y/Pb/Pr Input:

Sets BETACAM levels

If set for COMPOSITE Input

For inputs without Pedestal

If set for COMPONENT Y/Pb/Pr:

Sets SMPTE/EBU-N10 levels

If set for COMPOSITE Input:

Pedestal is removed on inputs with 7.5 IRE

Pedestal

If set for COMPONENT Y/Pb/Pr Input:

Sets Japan BETACAM levels

If set for COMPOSITE Input

For inputs without Pedestal

If set for COMPONENT Y/Pb/Pr:

Sets SMPTE/EBU-N10 levels

ON OFF

Notch Filter on (Comb Filter off) Comb Filter on (Notch Filter off)

ON OFF

EDH not inserted EDH inserted

Switch 3 Settings for

BETAJ Version of

D10AD

Switch 3 Settings for

Standard Version of

D10AD

Switch 7—Configure Automatic Gain Control (AGC)

Switch 8—Turn Test Pattern Output ON/OFF

Installation

Typically, D10AD installation consists of the following:

disconnect +5VDC from the convertor

conﬁgure the DIP switch for the desired equipment conﬁguration and video formats

connect video equipment to the convertor BNCs

apply +5VDC power to the converter (AJA power supply model DWP)

Specifications

ON OFF

Automatic Gain ON Automatic Gain Off (Unity Gain)

ON OFF

Internal color bars are output Disables test pattern output (normal video

operation)

Item Speciﬁcation

Serial Outputs SDI (SMPTE 259M) w/EDH

All outputs are separately buffered

4 x BNC

Frequency Response Y +/-0.15db to 5.5 Mhz

C +/-0.15db to 2.5 Mhz

2T K factor Less than .5% K Factor (2T)

Differential Gain < 1%

Differential Phase < 1 degree

A/D Converters 10 bits, 2X oversampling

User Controls Selectable By External Dip Switch:

Input Video Format

Pedestal Present/Not Present

Narrow/Wide Blanking

AGC On/Off

EDH On/Off

Test Pattern

Power

(AJA power supply model DWP)

5v DC regulated, 4 watt

Size 147 x 79 x 25 mm (5.8" x 3.1" x 1")

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - FAX 781.665.0780 - TestEquipmentDepot.com

Table des matières

Autres manuels AJA Convertisseur de média

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur