AIRMAC DB40 Manuel utilisateur

Diann Bao Inc.

www.airmac.com.tw E-mail: [email protected] Tel: +886-4-7621838

Fax: +886-4-7617617

Linear Air Pump

Model No. DB40

Performance / Rendimiento / Prestanda

★Allowance：±5%

Performance Curves DB40

0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45

Pressure = kg / cm

Q = L / Min.

110~120V 60Hz

220~240V 50Hz

Exhaust

Dimensions / Dimensioner （mm）

Operating range：0.05 to 0.2 kg/cm2

Model No. Voltage

(VAC)

Frequency

(HZ)

Rated

Pressure

(kg/cm2)

Airflow

(LPM)

AMP

(A)

WATT

(W)

DB40 110 ~ 120 60 0.13 47 0.9 45

DB40 220 ~ 240 50 0.13 48 0.41 41

< 38 dBA 20 - 80

-10

oC 6 kg

+40

v170310

DB version series 40

NO. DESCRIPTION QTY

1 TOP SCREW 1

2 FILTER COVER 1

3 FOAM SEAL 1

4 FILTER 1

5 UPPER HOUSING 1

6 THERM

L PROTECTOR 1

7 ELECTROMAGNET 2

8 WIRE STOPPER 1

9 U-SHAPED COIL FRAME 1

10 L

–

TUBE 2

11 VIBRATION CONTROL RUBBER 4

CTIVATING ARM 1

13 DIAPHRAGM FRAME 2

14 DIAPHRAGM 2

15 U NUT 2

16 DIAPHRAGM HOUSING 2

17 CHECK VALVE 4

18 CHAMBER SEAL

(

ROUND

)

19 CHAMBER SEAL

(

OVAL

)

20 SIDE COVER

(

STEEL

)

21 POWER CORD 1

22 STEEL PLATE 1

23 GASKET 1

24 LOWER HOUSING 1

25 RUBBER FEET 4

Figure 1

Maintenance Manual

DB version 40、60、80

1. To clean the air filter（Recommended once every six months）

A. Loosen the screw on top. (As shown in Figure1)

B. Remove the filter cover.

C. Take the filter out and clean it with clean water and dry it.

D. Put it back and secure the fixing plate with the screw in.

2. To change the diaphragms

IMPORTANT：To open the upper housing, please make sure you

have unplugged the power cord before opening.

A. Loosen the four screws around the aluminum upper housing,

and take the housing off. (As shown in figure 2)

B. Loosen the four screws and disassemble the parts. (As shown in figure 3)

C. Loosen the u-nut in the center of diaphragm.

D. Take the diaphragm off its place.

E. Replace a new one by mounting the rubber studs

into their position.

F. Press the rim of the diaphragm into the ring.

G. Secure the magnet with a new u-nut and screw and put

the diaphragm housing back with the four screws on.

Figure 2

Figure 3

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels AIRMAC Pompe à eau

AIRMAC

AIRMAC DT60 Manuel utilisateur

AIRMAC

AIRMAC DBMX250 Manuel utilisateur

AIRMAC

AIRMAC DBM80 Series Manuel utilisateur

AIRMAC

AIRMAC DBMX200 Manuel utilisateur

AIRMAC

AIRMAC DT40 Manuel utilisateur

AIRMAC

AIRMAC DBMX500 Manuel utilisateur

AIRMAC

AIRMAC DBMX100 Manuel utilisateur

AIRMAC

AIRMAC DBMX400 Manuel utilisateur

AIRMAC

AIRMAC DBMX150 Manuel utilisateur

AIRMAC

AIRMAC DBMX80 Manuel utilisateur

Manuels Pompe à eau populaires d'autres marques

Neptun

Neptun NPHW 5500 Manuel utilisateur

Sensidyne

Sensidyne Gilian BDX-II Instructions d'installation et d'utilisation

Draper

Draper 47808 Manuel utilisateur

Trolla

Trolla 12820 Manuel utilisateur

Sunfab

Sunfab SVH Series Manuel utilisateur

WilTec

WilTec 50740 Manuel utilisateur

Fieldmann

Fieldmann FVC 5015 EK Manuel utilisateur

Everbilt

Everbilt EFSUB5-122HD Manuel utilisateur

Graco

Graco Husky 3300e Manuel utilisateur

esotec

esotec 101018 Manuel utilisateur

moyno

moyno 2000 CC Manuel utilisateur

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuel utilisateur

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guide de dépannage

DUROMAX

DUROMAX XP WX Series Manuel utilisateur

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuel utilisateur

Franklin Electric

Franklin Electric IPS Manuel utilisateur

Xylem

Xylem e-1532 Series Manuel utilisateur

Milton Roy

Milton Roy PRIMEROYAL Manuel utilisateur