Airlink101 AP421W Manuel utilisateur
Super G™ Wireless Access Point
Model # AP421W
User’s Manual
Ver. 1B
2
Table of Contents
1. Introduction................................................................................................................................. 3
2. Getting Started............................................................................................................................ 4
3. Gathering Information ................................................................................................................ 6
4. Configuring Network Address.................................................................................................... 7
5. Using Web Configuration Utility.............................................................................................. 14
6. Connecting to the Access Point ................................................................................................ 19
7. Web Configuration Utility........................................................................................................ 20
7.1 Primary Setup...................................................................................................................... 20
7.1.1 Wireless Encryption Settings....................................................................................... 24
7.2 System................................................................................................................................. 27
7.3 Operating Mode.................................................................................................................. 29
7.4 Access Control.................................................................................................................... 34
7.5 Advanced Wireless ............................................................................................................. 36
7.6 Setting Status ...................................................................................................................... 38
7.7 Help..................................................................................................................................... 39
Technical Support......................................................................................................................... 40
3
1. Introduction
Congratulations on your purchase of this Super G™ Wireless Access Point. The Access
Point features four operating modes. The Access Point mode connects your wireless
clients with the wired part of your network. The AP client mode acts as a wireless
network adapter for your PC or game console. The AP Repeater mode extends the
range of your access point/wireless router by repeating the signal to wireless clients that
are beyond the broadcasting range of the access point/wireless router. This provides
the wireless clients with greater flexibility and mobility. Finally, the Point to Point Bridge
mode bridges the network clients from two physically separate LANS into one virtual
LAN.
The Access Point is compatible with existing 802.11b and 802.11g network devices so it
will work with most existing wireless devices. If you have other Super G™ compatible
wireless network device, you can also enable Super G™ on the Access Point for faster
transfer rate.*
Instructions for installing and configuring this product can be found in this manual.
Before you install and use this product, please read this manual carefully for proper
operation of this product.
Package Contents
Before you begin the installation, please check the items of your package:
•Super G™ Wireless Access Point
•Power Adapter
•RJ-45 Network Cable
•Antenna
•Quick Installation Guide
•Manual CD
If any item contained is damaged or missing, please contact your local dealer
immediately. Also, keep the box and packaging materials in case you need to ship the
unit in the future.
4
2. Getting Started
Please refer to the following diagrams to determine which operating mode you should
use for your network.
5
If you want to use the AP421W as an Access Point with minimal configuration, just
connect it to your existing router or switch with a Cat. 5 network cable and then power it
on. The Access Point is ready to use with its default settings:
SSID: default
Channel: 6
Encryptions: disabled
If you want to configure the Access Point’s settings or set it to other operating modes,
please follow the rest of this guide.
Step 1 Connect one end of a network cable to the Network port of the Access Point
and connect the other end to one of the LAN ports of the router (See the diagram
below).
Step 2 Power on the Access Point by connecting one end of the supplied power
adapter to the power jack of the Access Point and connecting the other end to an
electrical outlet.
Step 3 Verify that all three lights on the Access Point are lit. If not, verify that all the
connections are secure and try again.
6
3. Gathering Information
Step 1 On the wired computer, go to Start, Run, type command (for Windows
95/98/ME) or cmd (for Windows 2000/XP) and click OK.
Step 2 Type ipconfig and press Enter. Your network settings will be displayed.
Step 3 Write down the values for the IP Address, Subnet Mask, and Default Gateway
on a piece of paper.
Step 4 If you want to set the AP421W to a mode other than an Access Point, write
down the following values for your existing wireless router or AP:
1. SSID (Network Name)
2. Channel Number
3. Wireless Security Settings
The AP421W needs to use the same wireless settings in order for it to work properly.
You may gather these information from the web configuration utility of your wireless
router.
Step 5 Refer to the IP Address you’ve written down from Step 3.
If the first three numbers of your IP Address are 192.168.1, then you do not need to
configure your computer’s IP Address. Please continue to Section 5, Using Web
Configuration Utility.
If the first three numbers of your IP Address are not 192.168.1, (Ex. 192.168.2), then
please refer to the next section for instructions on how to change the IP Address.
7
4. Configuring Network Address
This section describes how to change your computer’s IP Address to access the Access
Point’s Web Configuration Utility and then to change the Access Point’s IP Address to
match your existing Network Address.
Step 1 Go to Start > Settings > Control Panel > Network and Internet Connections.
Step 2 Select Network Connections.
8
Step 3 Right-click on Local Area Connection and select Properties.
Step 4 Select Internet Protocol (TCP/IP) and click on Properties.
9
Step 5 Select Use the following IP address and enter the following:
IP Address: 192.168.1.101
Subnet Mask 255.255.255.0
Click OK when done.
Step 6 Click Close.
10
Step 7 Open your web browser (Internet Explorer or Netscape) and enter
192.168.1.250 in the Address Bar and press Enter.
Step 8 Enter admin for both the User name and Password and click OK.
Autres manuels pour AP421W
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Airlink101 Point d'accès sans fil
Airlink101
Airlink101 AP431W Manuel utilisateur
Airlink101
Airlink101 APO1010 Manuel utilisateur
Airlink101
Airlink101 APO1200 Manuel utilisateur
Airlink101
Airlink101 AP431W Manuel utilisateur
Airlink101
Airlink101 APO1000 Manuel utilisateur
Airlink101
Airlink101 AP421W Manuel utilisateur
Airlink101
Airlink101 APO1010 Manuel utilisateur
Airlink101
Airlink101 AP671W Manuel utilisateur
Airlink101
Airlink101 AP671W Manuel utilisateur
Airlink101
Airlink101 AP411W Manuel utilisateur
Manuels Point d'accès sans fil populaires d'autres marques
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur
Ubiquiti
Ubiquiti NanoStation NSM2 Manuel utilisateur
Cisco
Cisco Aironet 1550 Series Manuel utilisateur
Aruba
Aruba IAP-335 Manuel utilisateur
Advantek Networks
Advantek Networks AWN-AP-54MR Manuel utilisateur
IP-COM
IP-COM AP355 Manuel utilisateur
