AIRBORNE Activ Mode d’emploi
Activ
gNOTE: THIS FAN MUST BE INSTALLED BY A LICENSED AND QUALIFIED
ELECTRICIAN IN ACCORDANCE WITH LOCAL AUTHORITY REGULATIONS
Australian Edition Version 1.2 September 2021
Installation & User Manual
PLEASE NOTE: THE FAN WILL ONLY OPERATE
WITH THE WALL MCU CONTROLLER SUPPLIED
SEE BACK PAGE
ATTENTION ELECTRICIANS:
ANY PROBLEMS FOUND DURING INSTALLATION OF THE FAN PLEASE CONTACT THE NATIONAL
WARRANTY NUMBER PRIOR TO LEAVING SITE.
DO NOT REMOVE THE FAN FROM THE CEILING
UNLESS INSTRUCTED TO DO SO.
National Warranty Number | 1300 116 305 Monday to Friday 9am to 5pm AEST
NOTE: THIS FAN MUST BE INSTALLED BY A LICENSED AND QUALIFIED
ELECTRICIAN IN ACCORDANCE WITH LOCAL AUTHORITY REGULATIONS
1
IMPORTANT INFORMATION - PLEASE READ BEFORE ATTEMPTING INSTALLATION
Please Note: Nothing in this manual is intended to instruct or assist untrained or
unqualied persons to install this product. Additionally, it is the responsibility of the
installer and user to apply common sense and care at all times.
Please note: Minor design changes may result in slight variations between the product illustrations and the fan contained within the packaging.
1. Please read these instructions carefully, be mindful of all warnings and safety information shown throughout this
manual. Should you have any questions, please contact 1300 116 305.
2. Please review the accompanying assembly diagrams before attempting installation.
3. This fan MUST be installed by a licensed & qualied electrician according to local authority regulations and in
accordance with current wiring rules AS/NZS3000. Therefore, to protect our repair personnel, on-site warranty
claims will not be accepted if products have been installed by unlicensed persons.
4. A copy of the purchasing receipt and proof of installation by a licensed and qualied electrician according to local
authority regulations is required for all warranty claims.
5. Where special access equipment is required in accordance with local authority regulations all associated costs are
the responsibility of the owner.
6. We reserve the right to charge a $175 service fee for all call outs where the fan is found not to be defective and
/ or where access is not provided.
7. An isolation switch providing full disconnection of both fan and light must be tted in accordance with the wiring
rules (AS/NZS 60335.1 C1.7.12.2). In addition to all pole disconnection an isolation switch must be installed for
each individual fan located in the same room to allow for programming and ongoing maintenance.
8. The Fan and Light (if supplied) must be earthed.
9. Your warranty will be void if a solid state dimmer or any other brand of wall or remote controller is used.
10. Installation using steel beams, grid ceilings and exible structures are not recommended due to their inability to
absorb vibration from normal operation. Timber is the recommended material to support the fan.
11. To avoid possible electric shock during installation, be sure electricity is turned off at the main power box before
commencing work. Disconnect power by removing fuse or turning off circuit breaker before installing the fan.
Ensure all spliced connections are adequately insulated.
12. Warning! Do not allow the rotating fan blades to come into contact with any object, this can cause serious injury
or death.
13. Damage caused by; incorrect installation, Force-majeure, lightning, electrical surges & spikes, exposure to water,
pests or moisture is not covered under warranty.
14. In accordance with AS/NZS60355-1 & ASNZS60355-2-80: “This appliance is not intended for use by persons
(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not play with the appliance.”
15. Children should be supervised to ensure that they do not play with the appliance.
16. Children shall not play with the appliance.
17. Cleaning and user maintenance shall not be made by children.
18. Blades must be replaced only as a complete set. Blades are supplied only as a pre-balanced set and the replacement
of individual blades may void the warranty by causing mechanical damage to the motor, excessive noise or
premature wear.
19. Do not use outdoors where the fans could be directly exposed to water or moisture. Incorrect installation can be
dangerous and will void the warranty.
20. No more than eight (8) Hybrid AC Technology fans per lighting circuit as this may cause intermittent tripping.
National Warranty Hotline|1300 116 305 Monday to Friday 9am to 5pm AEST 2
Provide adequate clearance from the oor. The lowest point on the
fan blades must be at least 2.1m (7 feet) from oor level in Australia
and at least 2.3m from oor level in the European Union and afliated
countries.
Make sure that the chosen location of the fan will not allow the rotating
fan blades to come into contact with any objects.
Ensure ceiling joists are sound and of adequate size and strength to
support a 25Kg (55lb) load.
To reduce the risk of re, electrical shock or personal injury, ensure
that the fan mounting bracket is supported directly from the building
structure. DO NOT mount to an outlet box.
The mounting bracket must be rmly screwed to a load bearing structure e.g. a concrete ceiling, steel structure or
timber frame. If a timber frame is to be added it must be securely nailed or screwed between two beams.
After the fan is completely installed, check to make sure that all connections are secure to prevent the fan from falling
and/or causing damage or injury.
To reduce the risk of personal injury, do not bend or damage the motor or Fan Assembly when handling or during
installation.
Please ensure special care is taken when assembling the fan. Each screw must be sufciently tightened.
LOCATION AND INSTALLATION REQUIREMENTS
TABLE OF CONTENTS
Fan assembly & parts list - without LED light kit.........................
Fan assembly & parts list - with LED light kit..............................
Installing Hanger bracket..........................................................
Installing fan...........................................................................
Optional Accessory Extension Rod Installation............................
Summer & Winter Mode Explained............................................
Change LED Colour Temperature (with light version)......................
General Information.................................................................
General maintenance & cleaning...............................................
Troubleshooting.......................................................................
Ceiling fan warranty information................................................
Not covered by warranty...........................................................
Documents to retain for future warranty claims..........................
Electrician Checklist..................................................................
Fan Wiring Diagram..................................................................
Page 3
Page 4
Page 5
Page 6
Page 7
Page 8
Page 9
Page 10
Page 10
Page 11
Page 12
Page 13
Page 13
Page 14
Page 15
minimum
2100mm
Floor Level
Ceiling
NOTE: THIS FAN MUST BE INSTALLED BY A LICENSED AND QUALIFIED
ELECTRICIAN IN ACCORDANCE WITH LOCAL AUTHORITY REGULATIONS
3
FAN ASSEMBLY & PARTS LIST - WITHOUT LIGHT KIT
Unpacking your Fan
Unpack your fan and check the contents. Please check each item prior to installation, should you nd any issues please
contact the Warranty Helpline on 1300 116 305 for assistance. To reduce the chance of marks or possible damage
please only remove the parts when required for installation.
To avoid possible electrical shock, be sure
electricity is turned off at the main fuse box
before assembling and wiring the fan.
WARNING
Part Quantity Part Quantity
Hanger Bracket 1 Fan Motor 1
Hanger Bracket Screws 2 ABS Blades 4
Ceiling Bracket Covers 1 Blade Screws 4
DC Receiver 1 Bottom Cover 1
MCU Wall Controller 1
Hanger Bracket
Hanger Bracket Screws
DC Receiver Blades
Blade Screws
Fan Motor
Ceiling Bracket Cover
Downrod
Downrod Cover
Hanger Ball
Ceiling Bracket Screws
Top Motor Cover
MCU Wall Controller
National Warranty Hotline|1300 116 305 Monday to Friday 9am to 5pm AEST 4
FAN ASSEMBLY & PARTS LIST - WITH LED LIGHT KIT
Unpacking your Fan
Unpack your fan and check the contents. Please check each item prior to installation, should you nd any issues please
contact the Warranty Helpline on 1300 116 305 for assistance. To reduce the chance of marks or possible damage
please only remove the parts when required for installation.
To avoid possible electrical shock, be sure
electricity is turned off at the main fuse box
before assembling and wiring the fan.
WARNING
Part Quantity Part Quantity
Hanger Bracket 1 Fan Motor 1
Hanger Bracket Screws 2 ABS Blades 4
Ceiling Bracket Covers 2 Blade Screws 4
DC Receiver 1 LED Light Kit 1
MCU Wall Controller 1
Hanger Bracket
Hanger Bracket Screws
DC Receiver Blades
Blade Screws
Fan Motor
Ceiling Bracket Cover
Downrod
Downrod Cover
Hanger Ball
Ceiling Bracket Screws
Top Motor Cover
LED Light Kit
MCU Wall Controller
NOTE: THIS FAN MUST BE INSTALLED BY A LICENSED AND QUALIFIED
ELECTRICIAN IN ACCORDANCE WITH LOCAL AUTHORITY REGULATIONS
5
INSTALLING HANGER BRACKET - ENSURE CAN TAKE 25KG LOAD
12
3
4a4b
In accordance with Australian Standards, the fan blades must be at least 2.1 metres above oor level and the blades
require at least 300mm clearance to the nearest object. Ensure only the supplied Hanger bracket screws are used
Ensure ceiling joists are sound and of adequate size and strength to support a 25Kg (55lbs) load. If a timber frame is
to be added it must be securely nailed or screwed between two beams. Proper care must be taken when mounting to
concrete ceilings.
WITHOUT LIGHT - Three Wire WITH LIGHT - Four Wire
See back page for wiring diagram See back page for wiring diagram
National Warranty Hotline|1300 116 305 Monday to Friday 9am to 5pm AEST 6
DANGER! Before commencing installation, turn off electricity supply at the main power
box or disconnect power by removing fuse or turning off circuit breaker. This fan must be
installed by a licensed and qualied electrician in accordance with local authority regulations.
INSTALLING FAN
In accordance with Australian Standards, the fan blades must be at least 2.1 metres above oor level and the blades
require at least 300mm clearance to the nearest object.
1
3
2
4
5
NOTE: THIS FAN MUST BE INSTALLED BY A LICENSED AND QUALIFIED
ELECTRICIAN IN ACCORDANCE WITH LOCAL AUTHORITY REGULATIONS
7
DANGER! Before commencing installation, turn off electricity supply at the main power
box or disconnect power by removing fuse or turning off circuit breaker. This fan must be
installed by a licensed and qualied electrician in accordance with local authority regulations.
OPTIONAL ACCESSORY - EXTENSION ROD INSTALLATION
In accordance with Australian Standards, the fan blades must be at least 2.1 metres above oor level and the blades
require at least 300mm clearance to the nearest object.
1
3
2
4
56
National Warranty Hotline|1300 116 305 Monday to Friday 9am to 5pm AEST 8
SUMMER AND WINTER MODE EXPLAINED
FORWARD (Summer) Mode
Ceiling fans are an environmentally smart choice to assist with cooling and warming your home.
In FORWARD (Summer) mode your ceiling fan will spin to push air down the centre of the fan producing
a cooling breeze.
The direction the fan will spin in FORWARD (Summer) when viewed from underneath will be anticlockwise.
REVERSE (Winter) Mode
In REVERSE (Winter) mode your ceiling fan will spin the opposite direction. Air is drawn up the centre of
the fan, and pushed along the ceiling to circulate down to the living areas. The REVERSE (Winter) mode
can also be for air circulation in a poorly ventilated rooms. The direction the fan will spin in REVERSE
(Winter) when viewed from underneath will be clockwise.
NOTE: THIS FAN MUST BE INSTALLED BY A LICENSED AND QUALIFIED
ELECTRICIAN IN ACCORDANCE WITH LOCAL AUTHORITY REGULATIONS
9
DANGER! Before changing colour temperature on the light kit , turn off electricity supply to
the fan at the isolation switch and wait for fan blades to stop rotating.
CHANGE LED COLOUR TEMPERATURE WITH LIGHT VERSION
The light kit on the fan has three different colour temperature options 3000K / 4000K / 6000K. The fan has a switch
built into the light kit allowing the user to toggle between colour temperatures.
To change the colour temperature:
1. Ensure the fan is turned off at the isolation switch and the blades have stopped rotating
2. Remove light shade - see below item 1.
3. Select the desired colour temperature by moving switch
4. Test colour temperature by turning on light switch
5. Turn off light switch and install light shade - see item 3.
1
3
2
Table des matières
Autres manuels AIRBORNE Ventilateur
