aidapt VA147F Manuel
EN
Telescopic Channel Ramps
Fitting and Maintenance Instructions
Please read this manual before operation for maintenance
instructions and safe usage of these ramps.
Usage and Maintenance Instructions Ver. 1 01/2013 (2555)
2
CAUTION!
Always risk assess any situation for any possible risks.
Only use these ramps with a qualified helper, never exceed the recommended
weight limit during use.
Always back the wheelchair/scooter down the ramps and use a lap strap for
safety.
Always check the wheelchairs/scooters owners’ manual regarding the safe
incline for any particular chair.
N.B. This equipment must be installed by a competent person.
VA147F 4ft Channel Ramp
VA147H 5ft Channel Ramp
VA147M 6ft Channel Ramp
VA147S 7ft Channel Ramp
Maximum Load 272 kg (43 stone) using both ramps
Do not exceed the maximum load limit stated –doing so could put the
user at risk.
USING YOUR RAMP
Always fully extend the ramps before use to minimize the risk of injury,
and also make any ascent or descent using the ramps easier.
Select a place to use where the ramps have the minimum gradient
possible. Ensure the gradient of the ramps is not beyond the ability of
the wheelchair or occupant.
Place the narrow end of the ramp on the ground or low point, and
place the wide end of the ramp on the vehicle or high ground.
Ensure the ramps are safe before use.
TO EXTEND
Slowly pull out the narrowest section of the ramp whilst holding the
widest section, until it is locked in position.
WARNING! To prevent possible injury, please ensure when retracting
or extending the ramp that both sections are held firmly or that the
lower edge of the ramp is resting on the floor. DO NOT hold the ramp
in a raised position over feet or toes. The narrow section of ramp will
slide quickly down when the locking button is depressed.
Usage and Maintenance Instructions Ver. 1 01/2013 (2555)
3
To extend the ramp to its full length, continue to pull the narrowest
section of the ramp whilst pressing the button situated on the outside
of the ramp. Do this until the section is locked in position.
Repeat this for the other ramp.
TO RETRACT
Position the narrowest section into the main body of the ramp. Do this
by pressing the button whilst pushing the narrowest section into the
body of the ramp.
To complete the retraction operation, continue to push the narrowest
section into the body of the ramp whilst pressing the button. Do this
until the ramp is locked into position.
Repeat this for the other ramp.
MAINTENANCE & SAFETY
Regularly check your ramps for worn, loose or damaged parts –If you
find any of these to be damaged you must not use your ramps and
you must contact your dealer immediately.
Always use both ramps, and ensure they are level and parallel to each
other.
Ensure ramps are fully extended and locked in position.
Do not attempt to use ramps at a gradient above 1 in 12. Please also
check the gradient your wheelchair or scooter is capable of.
Do not exceed the weight capacity of the ramps.
Only allow one person/ mobility vehicle to use the ramps at once.
The surface of the ramps may become slippery in icy or wet
conditions. Please exercise caution in these conditions.
Keep your ramps clean of any dirt or debris as this could interfere with
its sliding motion.
Always use the ramps in line with the wheelchairs/scooter
manufacturer’s guidelines; NEVER use it at a steeper gradient than
recommended.
Do not modify or add to your ramp as it could void any warranty
claims.
Do not use the ramp for anything other than its original intended
purpose.
Only clean your ramps with mild detergent.
Use caution when adjusting the length of your ramps and avoid any
pinch points.
Usage and Maintenance Instructions Ver. 1 01/2013 (2555)
4
CLEANING
Clean your ramp using a mild detergent with a slightly damp, soft cloth
only. Only use a mild detergent or disinfectant; never use an abrasive
cleaner.
After cleaning, leave the Ramps somewhere warm and dry to air or wipe
over with a dry, soft cloth. Do not leave in direct contact with a heat
source.
IMPORTANT INFORMATION
Please exercise common sense and do not take any unnecessary risks when
using this product; as the user you must accept liability for safety when using
the product.
Please do not hesitate to contact the person who issued this product to you or
the manufacturer (detailed below) if you have any queries concerning the
assembly/use of your product.
Aidapt Bathrooms Ltd, Lancots Lane, Sutton Oak, St Helens, WA9
3EX
Telephone: +44 (0) 1744 745 020 •Fax: +44 (0) 1744 745 001 •
Web: www.aidapt.co.uk
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels aidapt Système de levage
Manuels Système de levage populaires d'autres marques
morse
morse 82H-124 Manuel utilisateur
Braun
Braun NL955 Series Manuel utilisateur
haacon
haacon 1889.10 Manuel utilisateur
Protekt
Protekt AT 252 Manuel utilisateur
R. Beck Maschinenbau
R. Beck Maschinenbau HS 600 Manuel utilisateur
Nova Technology International, LLC
Nova Technology International, LLC NAS Series Manuel utilisateur
Genie
Genie Z-60/34 Manuel utilisateur
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Manuel utilisateur
Custom Equipment
Custom Equipment Hy-Brid 3 Series Manuel de programmation
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Manuel de programmation
