Agilent Technologies 6680A Guide de démarrage rapide

6684A-03

SERVICE NOTE

6684A GPIB Power Supply

Serial Number: See below

A9 Down Programmer Failures

Duplicate Service Notes:

6680A-04 0000A00000 / US36480157 except US36480140

6681A-04 0000A00000 / US36400444 except US36400434 and US36400441

6682A-03 0000A00000 / US36440295

6683A-03 0000A00000 / US36420359

6684A-03 0000A00000 / US36410425 except US36420317 and US36410320

To Be Performed By: Agilent-Qualified Personnel

Parts Required:

Parts to repair A9 Assembly if A9 is repairable:

For models 6680A and 6681A:

Qty 1 p/n 5064-0142

(kit containing 2 FET’s 5182-9080, 2 insulators 0340-1507 and 6 sockets 1251-4211)

For models 6682A, 6683A and 6684A:

Qty 1 p/n 5064-0141

(kit containing 2 FET’s 5182-9079, 2 insulators 0340-1507 and 6 sockets 1251-4211)

Continued

ADMINISTRATIVE INFORMATION

SERVICE NOTE CLASSIFICATION:

MODIFICATION RECOMMENDED

ACTION

CATEGORY: IMMEDIATELY

ON SPECIFIED FAILURE

AGREEABLE TIME

STANDARDS:

LABOR 3.0 Hours

LOCATION

CATEGORY: CUSTOMER INSTALLABLE

ON-SITE

SERVICE CENTER

SERVICE RETURN

INVENTORY: SCRAP

SEE TEXT

USED RETURN

PARTS: SCRAP

SEE TEXT

AVAILABILITY: PRODUCT’S SUPPORT LIFE AGILENT RESPONSIBLE UNTIL: December 2001

AUTHOR: PS ENTITY: 2100 ADDITIONAL INFORMATION:

PRINTED IN U.S.A.

SUPERSEDES: NONE

DATE: December 1999

1 of 3

Parts required if A9 Assembly is to be replaced:

For Model Number:

6680A: Qty 1 06680-60022 Down Programmer/Slow sense Assy

Qty 1 5064-0142 FET Kit

6681A: Qty 1 06681-60022 Down Programmer/Slow sense Assy

Qty 1 5064-0142 FET Kit

6682A: Qty 1 06682-60022 Down Programmer/Slow sense Assy

Qty 1 5064-0141 FET Kit

6683A: Qty 1 06683-60022 Down Programmer/Slow sense Assy

Qty 1 5064-0141 FET Kit

6684A: Qty 1 06684-60022 Down Programmer/Slow sense Assy

Qty 1 5064-0141 FET Kit

Situation:

The output voltage cannot be lowered rapidly when the output is disabled or programmed to a

lower voltage. Cause: the sockets for field effect transistors (FET’s), A9 Q981 and A9 Q982,

have been found to overheat disabling the down programmer ciruit. Often the A9 can be easily

and quickly repaired.

Solution / Action:

1) Using the disassembly procdures in the service manual, remove the top cover, the protective

RFI Shield (galvanized sheet metal) and the A10 control assembly.

2) Without removing the A9, visually inspect the area around the FET sockets on the A9 as-

sembly. Look for signs of overheating. If the board is badly damgaged as indicated by lifted

traces and/or burned circuit board material, the A9 assembly will need to be replaced. If the

A9 board material is only discolored continue with step 3. If the A9 has to be replaced, also

replace the FET’s. Use the normal procedure for replacing the A9 and FET’s and, in addi-

tion, follow step 6 below to solder the FET leads into the sockets.

3) Remove the screws holding the A9 FET’s down to the heatsink and unplug the FET’s from

the A9 assembly. Discard the old insulators and FET’s.

4) Remove overheated FET sockets from the A9 assembly: Using a soldering iron and long

nose pliers, heat up the sockets from the side facing the outside of the unit and carefully

push them part way in. Next grasp them from the inside and remove them. Be careful not to

drop solder or sockets into the unit. Clean the plated-thru holes with desoldering braid.

5) Insert the new sockets into the A9 (don’t solder them in yet). Insert the new FET’s into the

sockets and mount them to the heatsink using new insulators. Make sure that the sockets are

fully seated into the circuit board. Do not use heatsink compound or overtighten the screws.

6) Carefully flow solder around the sockets on the side facing away from the heatsink (out-

side) and then carefully flow solder around the FET leads and INTO the sockets on the side

facing the heatsink. By applying heat only to the sockets, the solder will draw into the sock-

ets and will not flow toward the body of the FET’s.

7) Re-install the A10 control assembly, shields, and cover by reversing the disassembly proce-

dure in the manual.

Continued

Page 2 Service Note 6684A-03

8) Test the down programming circuits: With no load attached to the power supply, monitor

the output voltage with an external voltmeter. Program the output voltage for the model’s

highest rated voltage. Switch the output off. If the down programmer circuit is operational,

the output voltage will drop to zero in a fraction of a second. If the down programmer cir-

cuit is not operational, the filter capacitors will take tens of seconds to discharge.

Service Note 6684A-03 Page 3

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Agilent Technologies Alimentation

Agilent Technologies

Agilent Technologies E361 A Series Manuel de service

Agilent Technologies

Agilent Technologies E3632A Manuel utilisateur

Agilent Technologies

Agilent Technologies 6621A Manuel utilisateur

Agilent Technologies

Agilent Technologies U8001A Manuel utilisateur

Agilent Technologies

Agilent Technologies E3633A Manuel utilisateur

Agilent Technologies

Agilent Technologies 6443B Manuel de service

Agilent Technologies

Agilent Technologies 6631B Manuel utilisateur

Agilent Technologies

Agilent Technologies E3632A Manuel utilisateur

Agilent Technologies

Agilent Technologies E3633A Manuel utilisateur

Agilent Technologies

Agilent Technologies 729-0800 Manuel utilisateur

Agilent Technologies

Agilent Technologies 66319B Manuel utilisateur

Agilent Technologies

Agilent Technologies 6029A Manuel utilisateur

Agilent Technologies

Agilent Technologies 6214A Manuel utilisateur

Agilent Technologies

Agilent Technologies E3633A Manuel utilisateur

Agilent Technologies

Agilent Technologies 6571A Manuel utilisateur

Agilent Technologies

Agilent Technologies E3630A Manuel de service

Agilent Technologies

Agilent Technologies N8900 series Manuel utilisateur

Agilent Technologies

Agilent Technologies 6622A Manuel utilisateur

Agilent Technologies

Agilent Technologies E3647A Manuel utilisateur

Agilent Technologies

Agilent Technologies E3632A Manuel utilisateur

Agilent Technologies

Agilent Technologies E364XA Series Manuel utilisateur

Agilent Technologies

Agilent Technologies Series N6700 Manuel utilisateur

Agilent Technologies

Agilent Technologies E3631A Manuel utilisateur

Agilent Technologies

Agilent Technologies N5700 Series Manuel utilisateur

Manuels Alimentation populaires d'autres marques

Monacor

Monacor PS-12CCD Manuel utilisateur

VOLTIMA

VOLTIMA MagicBox 15 Manuel utilisateur

Miller

Miller Auto Deltaweld 452 Manuel utilisateur

BCP

BCP PUOUBK Feuille d'instructions

HC 2210 Manuel utilisateur

Puls

Puls CT5.241 Manuel utilisateur

OCZ

OCZ ZX1250W Manuel utilisateur

iseg

iseg ECH 238 Manuel utilisateur

Power

Power XXL A Series Manuel utilisateur

Renogy

Renogy PHOENIX 300 Manuel utilisateur

HP 6200B Manuel de service

Epson

Epson Stylus Scan 2500 Manuel d'utilisation

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuel utilisateur

Puls

Puls MiniLine ML50.100 Manuel utilisateur

Puls

Puls AS-Interface SLA4.100 Manuel utilisateur

Kenwood

Kenwood PS-60 Manuel utilisateur

Elmdene

Elmdene G1380xN-y-s Series Manuel utilisateur

DTS

DTS Megashock 5 Manuel utilisateur