Agilent Technologies 33220A Manuel utilisateur

Agilent Technologies

Agilent 33220A

20 MHz Waveform Generator

User's Guide

UG_ED5.book Page 1 Thursday, March 1, 2012 11:28 AM

Agilent 33220A

20 MHz Function/

Arbitrary Waveform Generator

User’s Guide

Publication Number 33220-90002 (order as 33220-90100 manual set)

Edition 4, May 2007

Agilent 33220A at a Glance

The Agilent Technologies 33220A is a 20 MHz synthesized function

generator with built-in arbitrary waveform and pulse capabilities.

Its combination of bench-top and system features makes this function

generator a versatile solution for your testing requirements now and in

the future.

Convenient bench-top features

• 10 standard waveforms

• Built-in 14-bit 50 MSa/s arbitrary waveform capability

• Precise pulse waveform capabilities with adjustable edge time

• LCD display provides numeric and graphical views

• Easy-to-use knob and numeric keypad

• Instrument state storage with user-defined names

• Portable, ruggedized case with non-skid feet

Flexible system features

• Four downloadable 64K-point arbitrary waveform memories

• GPIB (IEEE-488), USB, and LAN remote interfaces are standard

• LXI Class C Compliant

• SCPI (Standard Commands for Programmable Instruments) compatibility

Note:

Unless otherwise indicated, this manual applies to all Serial

Numbers.

The Front Panel at a Glance

Note: To get context-sensitive help on any front-panel key or menu softkey,

press and hold down that key.

1Graph Mode/Local Key

2On/Off Switch

3Modulation/Sweep/Burst Keys

4State Storage Menu Key

5Utility Menu Key

6Help Menu Key

7Menu Operation Softkeys

8Waveform Selection Keys

9Manual Trigger Key (used for

Sweep and Burst only)

10 Output Enable/Disable Key

Knob

Cursor Keys

Sync Connector

Output Connector

The Front-Panel Display at a Glance

Menu Mode

Trigger Output

Mode

Numeric

Readout

Information Information Status

Units

Display

Icon

Softkey Labels

Graph Mode

To enter or exit the Graph Mode, press the key.

In Graph Mode, only one parameter label

Signal

Parameter

Name Parameter

Value

Ground

is displayed for each key at one time.

Front-Panel Number Entry

You can enter numbers from the front-panel using one of two methods.

Use the knob and cursor keys to modify the displayed number.

1. Use the keys below the knob to move the cursor left or right.

2. Rotate the knob to change a digit (clockwise to increase).

Use the keypad to enter numbers and the softkeys to select units.

1. Key in a value as you would on a typical calculator.

2. Select a unit to enter the value.

The Rear Panel at a Glance

Note: The External and Internal 10 MHz Reference Terminals (1 and 2,

above) are present only if Option 001, External Timebase Reference, is

installed. Otherwise, the holes for these connectors are plugged.

WARNING For protection from electrical shock, the power cord ground must not be

defeated. If only a two-contact electrical outlet is available, connect the

instrument’s chassis ground screw (see above) to a good earth ground.

External 10 MHz Reference Input Terminal

(Option 001 only)

Internal 10 MHz Reference Output Terminal

(Option 001 only)

3External Modulation Input Terminal

Input: External Trig/FSK/Burst Gate

Output: Trigger Output

5USB Interface Connector

6LAN Interface Connector

7GPIB Interface Connector

8Chassis Ground

Use the menu to:

• Select the GPIB address (see chapter 2).

• Set the network parameters for the LAN interface (see chapter 2).

• Display the current network parameters (see chapter 2).

In This Book

Quick Start Chapter 1 prepares the function generator for use and

helps you get familiar with a few of its front-panel features.

Front-Panel Menu Operation Chapter 2 introduces you to the front-

panel menu and describes some of the function generator’s menu features.

Features and Functions Chapter 3 gives a detailed description of the

functiongenerator’s capabilities and operation. You willfind this chapter

useful whether you are operating the function generator from the front

panel or over the remote interface.

Remote Interface Reference

Chapter 4 contains reference information

to help you program the function generator over the remote interface.

Error Messages Chapter 5 lists the error messages that may appear

as you are working with the function generator. Each listing contains

information to help you diagnose and solve the problem.

Application Programs Chapter 6 contains several remote interface

application programs to help you develop programs for your application.

Tutorial Chapter 7 discusses the fundamentals of signal generation

and modulation techniques.

Specifications Chapter 8 lists the function generator’s specifications.

You can contact Agilent Technologies at one of the following telephone

numbers for warranty, service, or technical support information.

In the United States: (800) 829-4444

In Europe: 31 20 547 2111

In Japan: 0120-421-345

Or use our Web link for information on contacting Agilent worldwide.

www.agilent.com/find/assist

Or contact your Agilent Technologies Representative.

Contents

Chapter 1 Quick Start 13

To Prepare the Function Generator for Use 15

To Adjust the Carrying Handle 16

To Set the Output Frequency 17

To Set the Output Amplitude 18

To Set a DC Offset Voltage 20

To Set the High-Level and Low-Level Values 21

To Select “DC Volts” 22

To Set the Duty Cycle of a Square Wave 23

To Configure a Pulse Waveform 24

To View a Waveform Graph 25

To Output a Stored Arbitrary Waveform 26

To Use the Built-In Help System 27

To Rack Mount the Function Generator 29

Chapter 2 Front-Panel Menu Operation 31

Front-Panel Menu Reference 33

To Select the Output Termination 35

To Reset the Function Generator 35

To Output a Modulated Waveform 36

To Output an FSK Waveform 38

To Output a PWM Waveform 40

To Output a Frequency Sweep 42

To Output a Burst Waveform 44

To Trigger a Sweep or Burst 46

To Store the Instrument State 47

To Configure the Remote Interface 48

Chapter 3 Features and Functions 53

Output Configuration 55

Pulse Waveforms 70

Amplitude Modulation (AM) 74

Frequency Modulation (FM) 79

Phase Modulation (PM) 85

Frequency-Shift Keying (FSK) Modulation 89

Pulse Width Modulation (PWM) 93

Frequency Sweep 99

Burst Mode 106

Table des matières

Autres manuels Agilent Technologies Onduleur

Agilent Technologies

Agilent Technologies 205AG Manuel de service

Agilent Technologies

Agilent Technologies 346A Manuel de service

Agilent Technologies

Agilent Technologies E4400-60246 Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies 33120A Manuel utilisateur

Agilent Technologies

Agilent Technologies E8247C PSG CW Manuel utilisateur

Agilent Technologies

Agilent Technologies E4400-60230 g Guide de démarrage rapide

Agilent Technologies

Agilent Technologies 8648A Manuel de service

Agilent Technologies

Agilent Technologies Agilent 33500 Series Manuel de service

Agilent Technologies

Agilent Technologies E4400B Manuel utilisateur

Agilent Technologies

Agilent Technologies U9391C Manuel de service

Agilent Technologies

Agilent Technologies 33120A Manuel utilisateur

Agilent Technologies

Agilent Technologies E8257D PSG Manuel utilisateur

Agilent Technologies

Agilent Technologies E4438C ESG Manuel utilisateur

Agilent Technologies

Agilent Technologies E4438C Manuel utilisateur

Agilent Technologies

Agilent Technologies N4970A Manuel utilisateur

Agilent Technologies

Agilent Technologies N5106A PXB Baseband Manuel utilisateur

Agilent Technologies

Agilent Technologies E4428C Manuel utilisateur

Agilent Technologies

Agilent Technologies MXG (Series A and B) Manuel utilisateur

Agilent Technologies

Agilent Technologies 33250A Manuel utilisateur

Agilent Technologies

Agilent Technologies PSG Series Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies 16522A Manuel utilisateur

Agilent Technologies

Agilent Technologies 8960 Manuel utilisateur

Agilent Technologies

Agilent Technologies n5181a Mode d'emploi

Agilent Technologies

Agilent Technologies E8257D/67D Manuel utilisateur

Manuels Onduleur populaires d'autres marques

Fourgroup

Fourgroup Easy Manuel utilisateur

Velleman

Velleman PI300M Manuel utilisateur

Sungrow

Sungrow SG350HX-US Manuel utilisateur

WilTec

WilTec 61897 Manuel utilisateur

SMA

SMA SUNNY BOY STORAGE 2.5 Manuel utilisateur

Simplicity

Simplicity LANDLORD 316 Manuel utilisateur

Santak

Santak SMAX 3000 Manuel utilisateur

ATON

ATON RA.Store-3 Manuel utilisateur

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manuel utilisateur

Tektronix

Tektronix CFG250 Manuel utilisateur

Champion

Champion 200989 Manuel utilisateur

Vanner

Vanner 20-500 Series Manuel utilisateur

GE GEP Manuel utilisateur

Astrel Group

Astrel Group Power Reducer Guide rapide

MULTIQUIP

MULTIQUIP GDP-5H Mode d’emploi

GoWISE

GoWISE PS1007 Manuel utilisateur

Promate

Promate PM13500D ES Manuel utilisateur

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manuel utilisateur