Agilent Technologies N9039A Guide de démarrage rapide

Installation Note

Part Number N9039-90004

Printed in USA December 2008

Agilent N9039A RF Preselector

Option BAB, 3.5 mm RF Connectors

Option 518, Type-N RF Connectors

Notice.

The information contained in this document is subject to change without notice.

Agilent Technologies makes no warranty of any kind with regard to this material, including

but not limited to, the implied warranties of merchantability and fitness for a particular

purpose. Agilent Technologies shall not be liable for errors contained herein or for

incidental or consequential damages in connection with the furnishing, performance, or use

of this material.

Installation Note N9039-90004 3

Option BAB, 3.5 mm RF Connectors Option 518, Type-N RF Connectors Installation Kit

Option BAB, 3.5 mm RF Connectors

Option 518, Type-N RF Connectors

Installation Kit

Products Affected: N9039A

Serial Numbers: All

To Be Performed By: (X) Agilent Service Center

(X) Personnel Qualified by Agilent

( ) Customer

Estimated Installation Time:

Estimated Adjustment and Verification Time:

1.0 Hours

3.0 Hours

4Installation Note N9039-90004

Option BAB, 3.5 mm RF Connectors Option 518, Type-N RF Connectors Installation Kit

Introduction

This kit contains all of the instructions and parts required to install Option BAB or

Option 518 on an Agilent N9039A RF Preselector.

This installation note provides instructions on how to change the RF INPUT and RF

OUTPUT front panel connectors.

IMPORTANT For installation of Option BAB the N9039AK-BAB license must be

installed.

For installation of Option BAB the license for N9039AK-BAB must be

removed.

Contents of N9039AK-BAB Kit

NOTE a. Part number and memory capacity subject to change

Quantity Description Agilent Part

Number

1 Installation Note This note

1 Option Upgrade Entitlement Certificate 5964-5178

4 Screw, M3 x 0.5, 8 mm, TORX - 10 0515-0372

1 USB Storage Device see Note a

2 EMI O-ring shielding 8160-1637

1 Cable, semi-rigid, RF Output N9039-21311

1 Cable, semi-rigid, RF Input N9039-21312

1 RF Input Connector Assembly N9039-60027

1 RF Output Connector Assembly N9039-60029

Installation Note N9039-90004 5

Option BAB, 3.5 mm RF Connectors Option 518, Type-N RF Connectors Installation Kit

Contents of N9039AK-518 Kit

Tools Required

❏N9039A RF Preselector Service Guide. This manual can be purchased as

N9039A-0BW or N9039-90002.

❏Personal computer with internet access and USB port

❏T-20 TORX driver

❏T-10 TORX driver

❏5/16-inch open end wrench

Quantity Description Agilent Part

Number

1 Installation Note This note

4 Screw, M3 x 0.5, 8 mm, TORX - 10 0515-0372

2 EMI O-ring shielding 8160-1637

1 Cable, semi-rigid, RF Output N9039-21307

1 Cable, semi-rigid, RF Input N9039-21310

1 RF Input Connector Assembly N9039-60028

1 RF Output Connector Assembly N9039-60030

6Installation Note N9039-90004

Option BAB, 3.5 mm RF Connectors Option 518, Type-N RF Connectors Installation Kit

Installation Procedure

CAUTION If the instrument is placed on its face during any of the following

procedures, be sure to use a soft surface or soft cloth to avoid damage to

the front panel, keys, or input connector.

1. Disconnect the instrument from ac power.

2. Refer to Figure 1. Using the T-20 driver, remove the four screws (two on each side)

(1) that attach the handle strap (2) on each side of the instrument.

3. Using the T-20 driver, remove the four screws (including washers) (3) that hold the

rear feet (4) in place.

4. Pull the instrument cover (5) off towards the rear of the instrument.

Figure 1 Instrument Outer Case Removal

Installation Note N9039-90004 7

Option BAB, 3.5 mm RF Connectors Option 518, Type-N RF Connectors Installation Kit

NOTE Make sure any connectors on the front panel are removed.

5. Refer to Figure 2. Using the T-10 driver, remove the eight screws (1), four on each

side, to detach the Front Frame Assembly from the chassis.

6. Refer to Figure 3. Pull the Front Frame Assembly carefully away from the chassis.

Remove the ribbon cable W1 from the mother board.

Figure 2 Front Frame Assembly Removal

Figure 3 Front Panel Cable

8Installation Note N9039-90004

Option BAB, 3.5 mm RF Connectors Option 518, Type-N RF Connectors Installation Kit

7. Refer to Figure 4. Loosen the three semi-rigid cables from the three front panel

connectors.

Figure 4 Front Panel Connector Semi-Rigid Cables

Installation Note N9039-90004 9

Option BAB, 3.5 mm RF Connectors Option 518, Type-N RF Connectors Installation Kit

8. Refer to Figure 5. Remove the chassis side right (outer) (1) by removing the screws

(2) using the T-10 driver.

Figure 5 RF Side Chassis Removal

9. Remove the RF Output connector (3) and cable W4. Replace with the new RF Output

connector and cable from the kit. Leave the screws loose.

10.Install the EMI O-ring on the RF Output connector.

11.Remove the RF Input connector (4) and cable W3. Replace with the new RF Input

connector and cable from the kit. Torque the screws to 9 inch-pounds and the cable to

10 inch-pounds.

12.Install the EMI O-ring on the RF Input connector.

13.Refer to Figure 5. Carefully position the chassis side (1) onto the chassis, taking care

to align W4 and W5 into the front panel connectors. Replace the screws (2). Torque to

9 inch-pounds.

14.Check the connection between the three semi-rigid cables and the three front panel

connectors. Torque the remaining screws to 9 inch-pounds and the cables to

10 inch-pounds.

15.Reattach the ribbon cable W1.

10 Installation Note N9039-90004

Option BAB, 3.5 mm RF Connectors Option 518, Type-N RF Connectors Installation Kit

16.Refer to Figure 2. Carefully position the Front Frame Assembly onto the chassis.

Ensure no cables are crushed. Replace the eight screws (1), four on each side of the

chassis. Torque to 9 inch pounds.

17.Slide the instrument cover back onto the deck from the rear. The seam on the cover

should be on the bottom. Be sure the cover seats into the gasket groove in the Front

Frame Assembly.

18.Replace the four rear feet to the rear of the instrument. Torque the rear feet screws to

21 inch pounds.

19.Replace the handle straps on both sides of the instrument. Torque the handle strap

screws to 21 inch pounds.

Autres manuels pour N9039A

Table des matières

Autres manuels Agilent Technologies Câbles et connecteurs

Agilent Technologies

Agilent Technologies E5346A Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies 34398A RS-232 Manuel utilisateur

Agilent Technologies

Agilent Technologies 85133E Manuel de service

Agilent Technologies

Agilent Technologies N6314A Manuel utilisateur

Agilent Technologies

Agilent Technologies 16048B Guide de démarrage rapide

Agilent Technologies

Agilent Technologies G3180B Mode d'emploi

Manuels Câbles et connecteurs populaires d'autres marques

Philips

Philips SWA6310 Manuel utilisateur

StarTech.com

StarTech.com CRJ4550PK Manuel utilisateur

Nohau

Nohau EMUL-IP2K-PC Manuel utilisateur

Foxun

Foxun SX-SP144E-HD4K2K Manuel utilisateur

Philips

Philips SWA3305W Manuel utilisateur

opticis

opticis Stretch DVIM1-1P0x Manuel utilisateur

Volkswagen

Volkswagen VAS 6558A Manuel utilisateur

NEXIBO

NEXIBO N-13 Manuel utilisateur

CYP

CYP PU-1H3HBTL Manuel utilisateur

Allen-Bradley

Allen-Bradley 1784-u2dhp Manuel utilisateur

Global Caché

Global Caché Flex Link Blaster Manuel utilisateur

Hauppauge

Hauppauge USB-Live2 Manuel utilisateur

Fenix

Fenix MPSV 15 Manuel utilisateur

BEGA

BEGA 71 085 Manuel utilisateur

Tesla

Tesla HPWC Manuel utilisateur

GAMERON

GAMERON LUXURY TV CABLE Manuel utilisateur

molex

molex Milli-Grid Dual row 87568 Series Manuel utilisateur

Burndy

Burndy Continental Industries thermOweld CRE-7 Manuel utilisateur