AGASIO A622W Manuel utilisateur
support@agasio.com Page | 0 713-893-4514
Wireless/Wired Network IP Camera
Night Vision and Remote Operation
A622W Wireless PT Camera
User Manual
www.agasio.com
support@agasio.com Page | 1 713-893-4514
Thank You for Your Purchase!
Agasio IP Cameras are designed and equipped primarily for local and
remote purposes such as home or office security surveillance. We provide
a variety of products suitable for any type of surveillance system setup,
including wired/wireless IP outdoor bullet cameras, IP outdoor dome PTZ
cameras, and IP Indoor PT cameras.
Please check the packaging to make sure you have received all items
including the camera accessories as follows:
- Agasio IP Camera
- Wi-Fi Antenna (If Wi-Fi compatible)
- Power Supply
- Installation Driver CD
- Mounting Bracket
Note: Please contact us immediately if there are any damaged items or if
the package is short of any of the accessories listed above.
If you have any additional questions or concerns, please feel free to contact
us at support@agasio.com or call us at 713-893-4514.
support@agasio.com Page | 2 713-893-4514
Table of Contents
1. Product Introduction Page 3
2. Product Specifications Page 4
3. Hardware Installation Page 5
4. Software Installation Page 6
5. Software Operation Page 8
6. Viewing Live Video Page 11
7. Viewing With Internet Explorer Page 13
8. Viewing With Chrome, Firefox, Safari Page 17
9. Main Menu Interface Page 18
10. Administrative Settings Page 21
11. Multi-Device Settings Page 22
12. Basic Network Settings Page 25
13. Wireless Settings Page 25
14. ADSL Settings Page 30
15. Port Forwarding On Different Routers Page 30
16. Dynamic DNS Settings Page 37
17. E-mail And FTP Settings Page 47
18. Alarm Settings Page 49
19. Hard Reset And Firmware Upgrade Page 50
20. Restoring Factory Defaults Page 51
21. Rebooting Your Camera Page 52
22. Warranty Information Page 53
1. Product Introduction
The Agasio A622W Wireless Pan/Tilt Outdoor IP Camera features a high quality video sensor combined
with a hardened IP66 waterproof enclosure as well as fifty foot night vision range. It also includes an IR-
Cut Filter lens for true color images that are not washed out. The camera supports remote internet
viewing, motion detection as well as a built in network video recording system. It is smartphone
compatible (iPhone, Android & Blackberry) and accessible over the internet using standard browsers
(Internet Explorer, Safari, Firefox & Chrome). It is also compatible with Synology, Foscam, Blue Iris and
most other surveillance software programs and NVRs which accept standard MJPEG streams.
1.1 Safety Instructions
(1) Use the proper power source.
Do not use this product with a power source that supplies more than the specified voltage, which
is 100 –240 V AC.
(2) Never insert anything metallic into the camera.
Inserting metal objects into the camera can cause electric shock, please be very wary of this.
(3) Do not operate in wet or dusty environments.
Avoid areas such as damp basements or dusty hallways.
(4) Do not attempt to disassemble the camera.
You may be subjected to severe electrical shock if you attempt to take apart the camera while the
camera is connected to its power source. If there are any unusual sounds or smells coming from
the camera, unplug it immediately and contact Agasio Customer Service at 713-893-4514.
(5) Handle the camera very carefully.
Dropping the camera on any hard surface may cause a malfunction. If the camera does not work
properly due to physical damage, please contact Agasio Customer Service to see if you are
eligible for repair of the camera or an exchange. Please also refer to the warranty page at the back
of this manual for further information.
support@agasio.com Page | 4 713-893-4514
(6) Comply with FCC and CE Rules.
This device complies with Part 15 of the FCC and CE Rules. Operation is subject to the following
two conditions:
1: This device may not cause harmful interference.
2: This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. This equipment complies with FCC and
CE radiation exposure limits set forth for uncontrolled environments. This equipment should be
installed and operated with a minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
2. Product Specifications
- Agasio cameras adopt high performance, strong function media processors (32-Bit RSIC)
- High sensor CMOS
- Optimized MJPEG video compression, high-definition image transmission
- Supports a maximum of 15 users viewing at the same time, no limit for service forwarders
- Built-in web server, standard browsers are used for real time monitoring and administration
- Supports Wi-Fi 802.11 b/g wireless networking protocols
- Supports remote system updating
- Supports DDNS analysis, LAN & Internet (ADSL, Cable Modem)
- Supports a variety of network protocols: TCP/IP, UDP, SMTP, PPPoE, Dynamic DNS,
DNS Client, SNTP, BOOTP, DHCP, FTP, SNMP
- Specific models support one and two-way audio (camera-to-user, user-to-camera)
- Supports motion detection alarm functions
- Supports image snapshots
- Automatic recovery function, auto reconnection available when network interruption detected
- Dynamic alarm function, configurable alarm time-schedule
3. Hardware Installation
Follow the steps below to set up your camera hardware. Make sure to follow each step carefully to
ensure that the camera operates properly.
1. Install the Wi-Fi antenna by twisting the antenna connector clockwise to the camera’s antenna port (for
wireless models).
2. Plug the power adapter port into camera’s power supply port. This may be external (outdoor models) or
internal (indoor models) depending on which camera you purchased.
3. Plug the network cable into the RJ-45 connecter which is found either on the external wiring (for
outdoor cameras) or on the back of the camera (for indoor cameras), and plug in the other side of the RJ-
45 cable to a port on your router/switch.
4. It takes approximately 30 seconds to boot up the camera, you will see the camera swivel automatically
a few seconds after it is plugged in, this indicates the camera has successfully powered on.
5. When the camera is correctly powered on and the network cable is connected properly, the green LED
on either the RJ-45 connector of the camera (for outdoor models) or the connector on the back of the
camera (indoor models) will remain solid. The yellow LED should continue to flash.
Figure 3.1 –Outdoor Camera Wiring (your camera may be slightly different)
Figure 3.2 –Indoor Camera Rear Ports (your camera may be slightly different)
support@agasio.com Page | 6 713-893-4514
4. Software Installation
Firstly, insert the CD into your CD drive, and then open the CD to see the files on your computer.
Figure 4.1 –Double-click your CD/DVD Drive to browse the CD files
Figure 4.2 –Double Click the “English” folder
1. Before continuing, we must first run and install the file named “OCX Setup.” Double-click this file,
and a dialogue box should appear that reads, “The installation finished successfully!” Press OK.
2. Next, click the application named “Search tool.” The program will begin to run automatically from
the CD. If you would like, this software can be copied to your desktop. This will be continued in
the next section, “Software Operation.”
support@agasio.com Page | 8 713-893-4514
5. Software Operation
When Search Tool is double-clicked, the software will show up as follows:
Figure 5.1 –Search Tool IP Camera Software
Note: The Search Tool IP Camera Software searches for cameras directly connected to the Local Area
Network (LAN) of the router the computer is connected to. Please make sure the computer you are using
Search Tool on is connected to the same router that the camera is connected to.
There are two different scenarios that may take place:
First Scenario
No IP Cameras can be found within the Local Area Network (LAN). After about a 1 minute search, the
Equipment List will not show any IP addresses or cameras. If this happens we recommend firstly clicking
the “Find” button at the bottom of the program to see if any cameras show up. If no cameras show up, try
closing the software and re-opening it again to see if any cameras are detected.
Second Scenario
The IP Cameras have been detected within the Local Area Network (LAN). All the IP Cameras will be
listed and the total number is displayed in the “Equipment” field as shown in Figure 5.1.
1. Current Computer –Fields under this section indicate the Computer’s IP Address information.
2. Equipment information –This section indicates the IP camera’s IP Address information.
3. If you find that the camera’s “Subnet Mask”, “Gateway”, “DNS Server” is not the same as your
current computer IP address information, you need to change the camera’s IP address. This is done
easily within the Search Tool by clicking the “Update” button, seen in Figure 5.2 below. You will be
prompted to confirm and enter administrative information. By default, the username is “admin” with no
password. The camera will then reconfigure itself and will disappear, then reappear in the list.
Figure 5.2 –Make Sure Your Subnet Mask, Gateway, and Primary DNS Matches the Camera’s
Table des matières
