AG Neovo F-415 Manuel utilisateur
1
Table of Content
PRECAUTIONS ................................................................................................. 2
INSTALLATION .................................................................................................... 2
POWER CONNECTION ......................................................................................... 2
USING THE TILT ................................................................................................. 2
MAINTENANCE ................................................................................................... 3
TRANSPORTING THE MONITOR ............................................................................. 3
GETTING STARTED ......................................................................................... 4
PACKAGE CONTENTS .......................................................................................... 4
INSTALLING AND REMOVING THE BASE ................................................................. 5
IDENTIFYING PARTS AND CONTROLS ..................................................................... 6
SETUP .............................................................................................................. 7
CUSTOMIZING YOUR MONITOR..................................................................... 9
WORKING WITH OSD GROUPS ........................................................................... 9
TROUBLESHOOTING..................................................................................... 12
ATTENTION...................................................................................................... 12
LCD PANEL DISPLAY TECHNICAL FEATURES AND SPECIFICATIONS... 13
INTERFACE FREQUENCY ................................................................................... 14
REGULATIONS ............................................................................................... 15
FCC COMPLIANCE ........................................................................................... 15
INFORMATION FOR USERS APPLICABLE IN EUROPEAN UNION COUNTRIES................ 16
INFORMATION FOR USERS APPLICABLE IN UNITED STATES OF AMERICA.................. 16
TCO'99.......................................................................................................... 17
2
Precautions
Installation
• Do not cover or block the ventilation ports on the rear of the monitor.
• Do not install the monitor close to heat sources such as radiators or air ducts, or
in a location exposed to direct sunlight, excessive dust, mechanical vibration, or
shock.
Power connection
• Use the correct power cord for your local voltage.
• Use an accessible outlet close to the monitor.
• Do not allow anything to rest on the power cable.
• Disconnect the power cable from the power supply if:
You will not use the monitor for an extended period.
The cable is damaged or frayed.
The monitor has been dropped or the cabinet damaged.
A distinct change in performance indicates a need for servicing.
Using the Tilt
• Use the monitor’s tilt capability to adjust its vertical orientation to an appropriate
position. Grasp the top corners of the monitor with both hands and tilt to the
desired angle.
+30
-5
3
Maintenance
• Clean the cabinet and controls with a soft cloth lightly moistened with a mild
detergent solution. Do not use any abrasive materials or solvents such as alcohol
or benzene.
• Do not rub, touch, or tap the surface of the screen with sharp or abrasive items
such as pens or screwdrivers, as the screen may scratch.
• Do not insert objects or spill liquids into the ventilation ports on the monitor’s rear,
as fire, electric shock, and/or unit failure may result.
Transporting the monitor
When transporting the monitor for repair or shipment, use the original carton and
packing materials.
4
Getting Started
Package contents
Before beginning, ensure that the carton contains the following items:
• Monitor
• Base
• Power cord
• CD-ROM containing Windows®information file
• Quick Guide
5
Installing and Removing the Base
To attach the base to the monitor, do the following:
When you open the box to take the base and put on the desk first. Then connect the
LCD Monitor and base please.
To remove the base, turn the monitor on its side or up-side down, push the pegs to lift
base off monitor.
6
Identifying parts and controls
The center front panel of the monitor carries the control array.
FRONT VIEW
The controls are, from left to right:
AUTO button
Automatically adjusts the picture and performance. The AUTO function
should be used the first time you use the monitor and after changing the
resolution and/or refresh rate of the input signal.
1) It must be pressing the AUTO button over 1 second to execute auto
adjustment.
Note:
2) If the OSD is acting, this key function will same as down button.
LEFT button
Navigates within the display
RIGHT button
Navigates within the display
DOWN button
Activates the OSD and navigates within the display
UP button
Activates the OSD and navigates within the display
LED indicator
Indicates the monitor’s operational mode; green for regular operation,
and amber for power saving mode.
Power switch
Turns the monitor on and off
7
Setup
Follow these directions to correctly set up your monitor.
1. Remove all packing materials and wrapping from the monitor
2. Place the monitor in its desired location. Ensure that there is space around the
monitor, especially the rear area.
3. With the computer turned off, connect the signal cable to the VGA port on your
PC. Make sure connection is secure.
4. With the monitor switched off, connect the power cord to the Monitor AC socket.
5. Connect the plug Pin of power cord to an AC power source.
A
C Power Jack Power Cord
6. Turn on the computer.
7. Press the power switch on the monitor. The display should appear. If no display
appears, check Troubleshooting in this manual.
8. Ensure that your computer display is set at 1024X768 pixels and 60Hz. Press
the AUTO button exceed 1 second. The monitor optimizes the display
automatically.
8
Note: The monitor is compliant with VESA FPMPMI standards and can be wall-
or arm-mounted. Before wall-mounting or arm-mounting, please
disassemble the monitor stand first.
1. Unscrew screws of the hinge bracket
2. Remove the stand from LCD monitor
2
1
3. The rear of this LCD display has four integrated 4 mm, 0.7 pitches threaded
nuts, as well as four 5 mm access holes in the plastic covering as illustrated
below. These specifications meet the VESA Flat Panel Monitor Physical
Mounting Interface Standard (paragraphs 2.1 and 2.1.3, version 1, dated 13
November 1997).
75mm
75mm
75mm x 75mm
Screw Mounting Options
4mm ,0.7pitch threaded holes x4
9
Customizing your Monitor
The On Screen Display (OSD) system provides a full range of customizable tools to
optimize your display.
Important: While full customization is available, we strongly recommend using
the AUTO settings, which are preset to fully optimize your monitor’s
performance. Simply presses the AUTO button exceed 1 second to
engage the AUTO settings. It is also recommended that you execute
the AUTO function following any change made to your display from
your computer.
Working with OSD Groups
Press any of the LEFT , or RIGHT buttons to open the OSD window.
OSD Function Menu
To access OSD Main menu, simply press
one of the Function Select control buttons,
and the menu diagram will pop up on the
screen as shown on Fig. 1-1:
Continue pressing the Function Select
buttons (left/right) to scroll through the
entire menu items ,then press Adjustment
Control buttons (up/down) to adjust content
of selected item.
Attention Firmware revision may have been updated into a latest version
while the version number shown on all OSD menus in this manual
will stay as Ver. 1.00.
Brightness & Contrast ( / )
• To fine-tune the monitor’s brightness and contrast, select the pertinent item from
the menu.
• Use the UP and DOWN buttons to set the display as desired on the 0-100
scales that appears at the bottom of the window.
Horizontal & Vertical Position ( / )
• To fine-tune the display’s position on the monitor screen, select the pertinent item
from the menu.
• Use the UP and DOWN buttons to set the display as desired on the 0-100
scales that appears at the bottom of the window.
Phase & Clock ( / )
• To fine tune picture performance to compensate for drifts in the computer signal,
select the pertinent item from the menu.
• Use the UP and DOWN buttons to set the display as desired that appears
at the bottom of the window.
Autres manuels pour F-415
3
Table des matières
Autres manuels AG Neovo Moniteur
AG Neovo
AG Neovo NSD-6501Q Manuel utilisateur
AG Neovo
AG Neovo PS-55 Manuel du propriétaire
AG Neovo
AG Neovo RX-W19 Manuel utilisateur
AG Neovo
AG Neovo X-W22 Manuel utilisateur
AG Neovo
AG Neovo MD-24 Manuel utilisateur
AG Neovo
AG Neovo X-22 Manuel utilisateur
AG Neovo
AG Neovo X-20 Manuel utilisateur
AG Neovo
AG Neovo H-17 Manuel utilisateur
AG Neovo
AG Neovo RX-W32 Manuel utilisateur
AG Neovo
AG Neovo TX-2401 Manuel utilisateur
AG Neovo
AG Neovo F-419 Manuel utilisateur
AG Neovo
AG Neovo DR-17P Manuel utilisateur
AG Neovo
AG Neovo X-22 Manuel utilisateur
AG Neovo
AG Neovo TX-32 Manuel utilisateur
AG Neovo
AG Neovo U-17 Manuel utilisateur
AG Neovo
AG Neovo RX-W19 Manuel utilisateur
AG Neovo
AG Neovo SC-19 Manuel utilisateur
AG Neovo
AG Neovo PM-48 Manuel utilisateur
AG Neovo
AG Neovo ER-192 Manuel utilisateur
AG Neovo
AG Neovo X-24 Manuel utilisateur
