AG Neovo HIP-Series Manuel utilisateur
HIP-Series HDMI over IP Extender
User Manual
www.agneovo.com
HIP-Series HDMI over IP Extenders
1
TABLE OF CONTENTS
Getting Started
Important Safeguards
Safety Instructions
Product Description
Package Content
Panel Descriptions
Making Connections and Operations
Applications
Setup HIP-TA and HIP-RA
Choosing a Network Switch
Specifications
Features
Specifications
Appendix
Maintenance
Product Service
HIP-Series HDMI over IP Extenders
2
Getting Started
Dear Customer, thank you for purchasing AG Neovo products. For optimum performance and
safety, please read these instructions carefully before connecting, operating or adjusting this
product. Please keep this manual for future reference.
Notice:
AG Neovo reserves the right to make changes in the hardware, packaging and any
accompanying documentation without prior written notice.
HIP-Series HDMI over IP Extenders
3
Important Safeguards
Please read all of these instructions carefully before you use the device. Save this manual for
future reference. What the warranty does not cover
• Any product, on which the serial number has been defaced, modified or removed.
• Damage, deterioration or malfunction resulting from:
• Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized
product modification, or failure to follow instructions supplied with the product.
• Repair or attempted repair by anyone not authorized by us.
• Any damage of the product due to shipment.
• Removal or installation of the product.
• Causes external to the product, such as electric power fluctuation or failure.
• Use of supplies or parts not meeting our specifications.
• Normal wear and tear.
• Any other causes which does not relate to a product defect.
• Removal, installation, and set-up service charges.
HIP-Series HDMI over IP Extenders
4
Safety Instructions
The HIP-Series, HDMI Extender has been tested for conformity to safety regulations and
requirements, and has been certified for international use. However, like all electronic
equipment’s, the HIP-Series should be used with care. Read the following safety instructions
to protect yourself from possible injury and to minimize the risk of damage to the unit.
• Do not dismantle the housing or modify the module.
• Dismantling the housing or modifying the module may result in electrical shock or burn.
• Refer all servicing to qualified service personnel.
• Do not attempt to service this product yourself as opening or removing housing may
expose you to dangerous voltage or other hazards
• Keep the module away from liquids.
• Spillage into the housing may result in fire, electrical shock, or equipment damage. If an
object or liquid falls or spills on to the housing, unplug the module immediately.
• Have the module checked by a qualified service engineer before using it again.
• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the
device before cleaning.
HIP-Series HDMI over IP Extenders
5
Product Description
Packing Contents
1) Main Unit. Transmitter or Receiver
2) Power adapter DC 5V/1A
3) IR-TX cable & IR-RX cable
4) User Manual
Panel Descriptions
Transmitter panel Receiver panel
Power port Infrared emi�er HDMI Power indicator light
Reset bu�on Status indicator light
Gigabit Ethernet
Power port Infrared emier HDMI Power indicator light
Reset buon Status indicator light
Gigabit Ethernet
HIP-Series HDMI over IP Extenders
6
HDMI over IP Extender HDMI over IP Extender
HDMI Source
HDMI Cable
IR Emitter
Cat5e/6 Cable
Transmitter Receiver
HDMI Cable
HDMI DisplayIR Sensor
DVD or STB Remote
Making Connections and Operations
1) Connect the HDMI signal source (Such as DVD, STB etc) to HDMI Transmitter.
2) Connect a Cat5e/6 cable to both the LAN of the transmitter and LAN port of the Receiver.
(The cables must follow the standard of EIA-TIA 568B).
3) Connect the HDMI display into the Receiver.
4) Connect the power supply into the Power port.
5) Connect the IR TX cable into IR TX port on the back panel and affix the emitter onto the
source IR sensor.
6) Connect IR-RX cable into IR-RX port on the receiver and affix the IR receiver in direct line of
site with the handheld remote control. It is recommended to affix the receiver on the display
frame/bezel or the display stand.
Attention: Insert/Extract cables gently.
Applications
Point-to-Point
HIP-Series HDMI over IP Extenders
7
Point-to-Multipoint
Note:
Connect Transmitter
and Receivers LAN ports
to the Ethernet Switch.
HDMI over IP Extender
HDMI over IP Extender
HDMI Source
HDMI Cable IR Emitter
Cat5e Cable
Transmitter
Receiver 1
HDMI Cable
HDMI Display 1
IR Sensor
DVD or STB Remote
HDMI over IP Extender
Receiver 2
HDMI over IP Extender
Receiver 3
HDMI over IP Extender
Receiver 4
Gigabit Switch
HDMI Cable
HDMI Display 2
IR Sensor
DVD or STB Remote
HDMI Cable
HDMI Display 3
IR Sensor
DVD or STB Remote
HDMI Cable
HDMI Display 4
IR Sensor
DVD or STB Remote
HIP-Series HDMI over IP Extenders
8
Multipoint-to-Multipoint
Notes:
1. Connect Transmitters and
Receivers LAN ports with a
managed Gigabit switch.
(a Managed Gigabit Switch
with VLAN and IGMP support
is recommended).
2. An HTTP server is embedded
into every HIP-TA and HIP-RA,
you can setup the IP address
for each unit via web browser.
HDMI over IP Extender
HDMI over IP Extender
HDMI Source
HDMI Cable IR Emitter
Cat5e Cable
Transmitter 2
Receiver 1
HDMI Cable
HDMI Display 1
IR Sensor
DVD or STB Remote
HDMI over IP Extender
Receiver 2
HDMI over IP Extender
Receiver 3
Managed Gigabit Switch
HDMI Cable
HDMI Display 2
IR Sensor
DVD or STB Remote
HDMI Cable
HDMI Display 3
IR Sensor
DVD or STB Remote
HDMI over IP Extender
HDMI Source
HDMI Cable IR Emitter
Transmitter 1
HDMI over IP Extender
HDMI Source
HDMI Cable IR Emitter
Transmitter 3
HIP-Series HDMI over IP Extenders
9
Setup HIP-TA and HIP-RA
An HTTP server is embedded into every HIP-TA and HIP-RA, you can setup the IP address for
each unit via web browser.
The default IP address of the TX is 192.168.168.55, MAC address is: 00:0b:78:00:60:01.
The default IP address of the RX is 192.168.168.56, MAC address is: 00:0b:78:00:60:02.
Step 1: Assign the PC (or laptop) IP address on the computer : “Control Panel”→”Network
Connections”→“Local Area Connections
Status”→“Properties”→“Internet Protocol (TCP/IP)”, fill in the IP address field with
192.168.168.11 (0-255) and Subnet mask with 255.255.255.0. After that press OK to save the
configuration.
Note: The IP address of PC should be different from the IP addresses of HIP-TA and HIP-RA
units.
Step 2: Use an Ethernet cable to connect the PC and the extender. the power LED for the
extender should become red and the status LED green.
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels AG Neovo Extenseur
