AFL OFI-BI Manuel utilisateur

KSP74-0119-16-14 (2)

Read this instruction manual carefully

before operating the equipment.

Adhere to all safety instructions and

warnings contained in this manual.

Keep this manual in a safe place.

OFI-BI

NOTE

External light detecting function

When external light such as sunlight is detected, both sides of the direction

indicator will turn on simultaneously. In case the external light is strong,

identifier function will not perform properly, so please cover the plunger

portion by hand and this will solve the problem.

Please refer to Page 25 for details.

ONU detecting function

When you see the message “Require optimization for use in your region”

or don’t find appropriate settings after accessing the “ONU Setup” menu,

this means the function is not activated yet in your region. After obtaining

the ONU signal in your region, AFL will release a firmware upgrade to

activate the function for the OFI-BI. Please consult your local AFL

distributor for more information.

INSTRUCTION MANUAL

OPTICAL FIBER

IDENTIFIER

Table of Contents

Table of Contents...........................................................................................1

Warnings and Cautions.................................................................................3

Recycling and Disposal .................................................................................6

Composition...................................................................................................8

1．Components ...............................................................................................................8

2．Description and Function..........................................................................................9

3．Power Supply...........................................................................................................11

Battery Operation......................................................................................................11

Description...................................................................................................12

1．Outline of Identifier Operation ..............................................................................12

2．Functions of OFI-BI................................................................................................13

3．Display of OFI-BI....................................................................................................14

Identifier Function......................................................................................14

1．Cleaning the Optical Detector................................................................................15

2．Attach or Remove the Plunger ...............................................................................15

3．Zeroing .....................................................................................................................16

4．Signal Selection........................................................................................................17

5．Trigger Hold.............................................................................................................19

6．Measurement Mode.................................................................................................20

Measurement ...............................................................................................21

1．Operation Procedure...............................................................................................21

2．Detecting external light...........................................................................................25

Other Functions...........................................................................................26

1．Auto Power Off Function........................................................................................26

2．Low Battery Alarm..................................................................................................26

3．Buzzer Volume.........................................................................................................27

4．Display Time ............................................................................................................28

5．Brightness.................................................................................................................29

6．Dimmer Time...........................................................................................................30

7．Error Displays..........................................................................................................31

8．Firmware Upgrade..................................................................................................31

Table of Contents

Before Storing in the Case...........................................................................31

1．Storing in the Case...................................................................................................32

Specifications...............................................................................................33

Warnings and Cautions

The OFI-BI has been designed for discriminating signals in optical fibers. Do not attempt to

use this instrument for other applications.

AFL gives much consideration and regard to personal injury. Misuse of the instrument may

result in electric shock and/or serious personal injury.

Read this instruction manual carefully before operating this instrument.

Store this instruction manual in a safe place.

Contents of this instruction manual may change without announcement.

The following alert symbols are used in this instruction manual and instrument to

indicate warnings and cautions for safe use. Understand the meanings of these

symbols.

WARNING

There is a possibility of death or serious injury resulting from improper

use by ignoring this indication.

There is a possibility of personal injury or physical loss resulting from

improper use by ignoring this indication.

Symbol means “Pay attention”

Symbol means “Must not do”

Symbol means “Must do”

You must disconnect a

Pay attention to Explosion!

You must not disassemble!

You must disconnect a plug!

CAUTION

Warnings and Cautions

WARNINGS

Remove the battery from the equipment immediately if user observes the

following or if the Identifier exhibits the following faults:

Fumes, bad smell, noise or if over-heating occurs.

Liquid or foreign matter falls into the interior of the Identifier.

The Identifier is damaged or dropped.

If this occurs, ask our service center for advice. Leaving the Identifier in a

damaged state may cause equipment failure, electric shock or fire and may result

in personal injury, death or fire.

When the equipment is behaving abnormally, there is a possibility of battery

leakage. So do not touch the battery directly.

Do not disassemble or modify the Identifier. It can cause an electric shock and

fire.

Do not touch the Identifier with wet hands. This may result in equipment failure

and electric shock.

Do not heat the battery nor incinerate it. This may result in personal injury by

explosion and fire.

Do not short-circuit the electrodes of the battery. Excessive electrical current may

cause personal injury, electric shock, fire and equipment damage.

Confirm the polarity of the battery and place it correctly. Incorrect placement

may result in battery leakage and personal injury by fire and equipment damage.

Using an improper power source may cause fuming, electric shock or equipment

damage and may result in injury, death or fire.

Warnings and Cautions

CAUTIONS

Do not store the Identifier under direct sunlight.

This may result in equipment failure.

Do not place heavy weight on the Identifier. This may result in equipment failure,

electric shock and fire.

Remove the batteries from the equipment when not using it for a long time.

Keeping the batteries in the equipment may cause the batteries to leak and

damage the equipment.

Do not recharge a non-rechargeable battery, e.g. a dry-cell battery.

This may cause heat, leakage or rupture of the unit and injury.

Use the appropriate battery charger specified by the battery manufacturer. Using a

charger not specified by the manufacturer could cause injury or fire.

The equipment must be repaired or adjusted by a qualified technician or engineer.

Incorrect repair may cause fire or electric shock. Should any problems arise,

please contact your distributor.

Perform fall preventive measures, such as attaching a strap, when working at

height. Dropping may cause damage of the equipment and personal injury.

Do not press on the LCD panel with sharp materials.

It may cause damage to the LCD.

Recycling and Disposal

RECYCLINGAND DISPOSAL

In European Union

In accordance with the European Parliament Directive 2002/96/EC, electrical

parts and materials that can be re-used and/or recycled have been identified in

order that the use of new resources and the amount of waste going for landfill can

be minimised.

In the European Union, do not discard this product as unsorted municipal waste.

Contact your local authorities.

In other countries

[Recycling]

To recycle this product, disassemble it first, sort each part separately by material

components and follow your local recycling regulations.

[Disposal]

This product can be disposed of in the same way as standard electric products.

Follow your local disposal regulations.

-------------------------------------Blank Page-------------------------------------

Composition

．

Components

Name

Model

Qty

Appearance & Comments

Optical Fiber

Identifier

OFI-BI-E

1pc

Plunger

PL-06

1pc

Case

OFI-CASE-01

1pc

Instruction Manual

IM-BIPM/BI

1pc

Quick Reference

Guide

QR-BIPM/BI-E

1pc

－

Composition

．

Description and Function

Battery Cover

Tone Indicator

Traffic Indicator

Plunger Portion

Clamping Trigger

OFI-BI Front Side

LCD

OFI-BI Side Surface

ONU Indicator

Plunger Cover

Optical

Detector

Table des matières

Autres manuels AFL Équipement de test

AFL

AFL Noyes OPM4-4 Manuel utilisateur

AFL

AFL FOCIS Manuel utilisateur

AFL

AFL NOYES OLS Series Manuel utilisateur

AFL

AFL FOCIS Lightning 2 Manuel utilisateur

AFL

AFL FlexScan FS300 Manuel utilisateur

AFL

AFL FOCIS Lightning 2 Manuel utilisateur

AFL

AFL Noyes OPM4 Manuel utilisateur

AFL

AFL MFIS Manuel utilisateur

AFL

AFL FlexTester 3 Manuel utilisateur

AFL

AFL OPM Series Manuel utilisateur

AFL

AFL FOCIS WiFi2 Manuel utilisateur

AFL

AFL M710 Series Instructions d'installation

AFL

AFL VFI 2 Manuel utilisateur

AFL

AFL WDM900 Manuel utilisateur

AFL

AFL Noyes OPM4-3D Manuel utilisateur

AFL

AFL ROGUE cB1 Manuel utilisateur

AFL

AFL VFI4 Manuel utilisateur

AFL

AFL ROGUE cB1 Manuel utilisateur

AFL

AFL FOCIS Duel Manuel utilisateur

AFL

AFL FlexScan FS200 OTDR Manuel utilisateur

AFL

AFL FR1 Series Manuel utilisateur

AFL

AFL OPM5 Manuel utilisateur

AFL

AFL MLP4-2 Manuel utilisateur

AFL

AFL OLS1 Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur