Aeroqual 200 series Manuel utilisateur

Series 300, 305, 500 & 505

Monitor

User Guide

200

Quick Start Guide

1. Unpack monitor and check supplied components are correct

2. Insert Battery (see section 3.0)

3. Insert Sensor

4. When new, plug in the power adaptor and turn on your monitor

(with sensor head installed) for 24hrs. Note: The battery requires

15hrs from full discharge. The sensor requires a run in period.

Thereafter, the normal warm up takes only 10 minutes. If your unit

is new or unused for a long period, a warm up message may dis-

play for several hours, then will disappear.

5. Follow the operating instructions to understand how to make the

most of your monitor

Warning:

•Do not expose the monitor to gas concentrations above the recommended

maximum range

•Do not place the sensor head in a gas stream – the monitor is designed to

measure ambient levels of ozone and uses ‘active sampling’ to achieve this.

1. Sensor Head

2. Power and Stand By

3. Display

4. Enter

5. Battery case. For battery installation, see

section 3.0 of your user guide

ZERO CAL: Please refer to section 4.5 of your user guide when using this

option, as this can uncalibrate your unit if performed incorrectly

CONC UNIT: To change the units of measurement, use the power key,

then press to return to the main menu. See section 4.6 of your user

guide for more information

MAX / MIN AV: To adjust the max / min av, press to alternate between

start and stop. See section 4.7 of your user guide for more information

EXIT

ZERO CAL

CONC UNIT

MAX MIN AV 

Contents

1.0 Monitor Components 3

2.0 About Your Monitor 4

3.0 Assembly and Installation 5

3.1 Battery pack 5

3.2 Sensor warm up 8

3.3 Monitor and Sensor Versions 8

4.0 Operating Instructions 9

4.1 Turning the Monitor on and off 9

4.2 Operating under battery power 10

4.3 Sensor Head Failure 10

4.4 Using the Menus & Key Functions 11

4.5 Zero Calibration 11

4.6 Changing Unit of Measurement 12

4.7 Max Min Average Measurement Cycle 12

4.8 Alarm Mute (Perc only) 13

4.9 Alarm (Perc only) 13

4.10 Alarm Level (Perc only) 14

5.0 Troubleshooting 15

6.0 Specifications 17

7.0 Drawings 18

8.0 Care and Maintenance 18

9.0 For Your Safety 20

10.0 Statements of Compliance 21

11.0 Warranty 22

12.0 Copyright 24

13.0 Guidelines on how to measure ozone 25

14.0 Zero calibration additional information 26

15.0 Sensors and accessories 27

08.11.2010 V1.1

1.0 Monitor Components

Series 200 Monitor

The following components are supplied with the Series 200

Monitor:

•Series 200 monitor base

•Gas sensor head

•12 VDC 800 mA AC/DC adaptor

•User guide

•Battery pack – 9.6 V

Please check that all these components have been supplied and

contact your dealer or Aeroqual by email at:

sales@aeroqual.com if any of the components are missing.

Replacements

Replacement batteries, sensor heads and other accessories can be

purchased separately.

Note:

All sensors deteriorate over time. It will be necessary to replace your

sensor head with either a new or refurbished head. This must be

done on a scheduled basis or when the “sensor aging” or sensor

failure” diagnostic appears. Bump tests, zero and span calibration

can be performed under specified conditions with appropriate tools.

2.0 About Your Monitor

The Aeroqual Series 200 Monitor has been specifically designed to

incorporate Aeroqual’s in-depth knowledge of accurate ambient gas

measurement. Different sensor heads are used for specific gases or

depending upon whether high or low concentrations are to be meas-

ured. The all sensor heads are interchangeable on the same base unit.

The following information details the operation and features of the moni-

tor:

1. The monitor is modular in design and is comprised of two main

components, a Series 200 monitor and a sensor head. This affords

the user the ability to replace faulty sensor heads without having to

replace the monitor. The monitor can be mains and/or battery pow-

ered and either permanently mounted or used as a portable unit.

2. The Aeroqual Series 200 Monitor comes with in-built diagnostics,

which will inform the user if the sensor is not operating correctly.

3. An audible alarm is available with perchloroethylene sensors only.

Both temporary and permanent mute functions are also included

with the audible alarm.

4. Concentration unit selection. The concentration can be displayed

in either ppm or mg/m3.

5. Min / max / average measurement cycle. The monitor will display

the minimum, maximum, average and 15-minute average gas con-

centrations over the measurement period.

3.0 Assembly and Installation

Assembly

The following needs to be completed before the Monitor is ready

for use: -

•Insert the sensor head into the top of the monitor. The sen-

sor head is keyed to ensure the head is inserted correctly.

•If the monitor is a mains only unit it is ready for use. If the

monitor is to be used as a portable unit with batteries then

the batteries must be installed and charged prior to use.

3.1 Battery Pack

•Remove the battery cover from

the monitor.

•Insert the battery power connector

into the monitor power socket in

the back of the monitor.

•Lay the battery cable into the slot

the back of the monitor and insert

the tail end of the battery pack into

the hinge points at the bottom of

the monitor back cover.

•Clip the top end of the battery pack

into the top clips, taking note to

orientate the battery pack per the

instructions on the battery pack.

•Replace the battery cover on the

monitor.

Removing the Battery Pack

•Remove the battery cover from the monitor.

•Insert your thumb under the top left hand side of the battery

pack and carefully lever the battery pack out from the retain-

ing clips.

•Unclip the connector from the monitor.

•Replace the battery cover.

Rechargeable Batteries

The optional Ni-MH (Nickel Metal Hydride) battery pack is used to

power the monitor as a portable unit. Please read the following infor-

mation carefully before using the battery pack to operate the Aero-

qual monitor.

Safety

•Do not use the battery pack for any other purpose than oper-

ating the Aeroqual monitor

•Do not disassemble or mutilate the batteries as this may

cause burns

•Do not incinerate or heat as this may cause burns, the batter-

ies may burst or cause the release of toxic materials

•Do not short circuit as this may cause burns

•Use only batteries approved by Aeroqual and recharge your

battery only with the AC/DC adaptors supplied by Aeroqual.

•Never use any charger or battery that is damaged or worn

out.

•Batteries must be recycled or disposed of properly. They

must not be disposed of in municipal waste.

•Never charge a Ni-MH in a hermitically sealed container.

Using the battery pack

The life of the battery pack will be affected by the way it is handled.

Take good care of the battery pack and follow the guidelines sug-

gested in the following section.

Charging and Discharging the Batteries

New Ni-MH batteries must be fully charged prior to use. A new Ni-

MH battery's full performance is achieved only after a number of

complete charge and discharge cycles. A fully charged battery will

run for approximately 4-5 hours. (Note: Perc sensor heads require

more power and will run for a shorter time)

Charging Instructions

1) Plug in the adaptor

2) Turn the monitor on

3) Allow 15 hours for the battery to fully charge.

Note:

•During charging the battery symbol on the display flashes

slowly.

•The battery can be charged with the sensor head installed or

removed from the base. (Remember to switch off the monitor

before removing the sensor head).

•Unplugging the main power will reset the above charging condi-

tions.

•The batteries can be charged and discharged many times but

will eventually wear out. When the operating time is noticeably

shorter than normal, it is time to replace the batteries.

•It is not necessary to fully discharge the batteries. When not

using the Series 200 Monitor as a portable unit, always plug in

the mains adaptor to recharge the batteries with the monitor

switched on.

•If left unused a fully charged battery will discharge itself over

time.

Note:

If you have difficulty charging the battery, either:

A) Replace the battery

B) Contact Aeroqual with the software version number

(see section 3.3 to locate the version number.)

Installing the AC/DC adaptor

•Connect the AC/DC adaptor to the mains supply. Ensure that

the adaptor is correctly rated for the power supply.

•Plug the adaptor into the monitor. The monitor can now be

used as a mains unit. If the monitor is to be used as a port-

able unit the batteries will need to be charged.

3.2 Sensor warm up

Prior to operation the monitor must be warmed up to burn off

contaminants on the sensor. When the monitor is first switched

on it will warm up for 3 minutes. Then the reading will flash for

the next 7 minutes to indicate that the sensor is still in the warm

up phase. It is recommended that the monitor is kept in Stand By

mode when not being used to keep the sensor heated and

prevent the build up of contaminants. If the sensor is new (or

unused for long periods) it can take up to 24 hours for the

message “sensor warming up” (or “sensor failure” in older

models) to disappear. Should the message remain after this time,

agenuine sensor failure may have occurred. See the trouble-

shooting guide.

Since O3 is an oxidising gas the warm up period can be reduced

by subjecting the sensor to elevated O3 levels for a short period.

For example, 100 ppb of O3 for 5 minutes typically reduces the

warm up time to 30 minutes.

24hrs is a conservative time for an ozone sensor to burn off con-

taminants and achieve its stated performance specification. In

most instances this will be achieved well within 24hrs.

Warning: Do not remove the sensor head while the monitor

is switched on. This may damage the unit. If the sensor head is

removed under these conditions, the unit will automatically shut

down.

3.3 Monitor and Sensor Versions

Turning the monitor on will display “AEROQUAL MONITOR

Vx.x”, where "V x.x" represents the version of the monitor

base. The display will then show “SVXX”which indicates the soft-

ware version installed on the sensor head.

4.0 Operating Instructions

The following instructions detail the operation and set up of the

monitor.

4.1 Turning the monitor on and off

To turn the monitor on, press & hold the power button until

the screen activates.The monitor will turn on and the display

will show “AEROQUAL MONITOR S200 / S205 Vx.x”,.After 5

seconds the display will change to indicate the type of sensor

head. The monitor will warm up as described in “Warm up”

in section 3.2. Once warm up is complete the main display will

appear (for example):

To turn the monitor off, press and hold the power button for

2seconds until the monitor beeps.The display will now be

blank and operation of the monitor will cease.

Power

button

Enter

Key

O3 LOW

0.009

ppm

Note:

The number of decimal

places shown will vary de-

pending on the sensor head

type

Autres manuels pour 200 series

Table des matières

Autres manuels Aeroqual Moniteur

Aeroqual

Aeroqual IQM 60 Manuel utilisateur

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Furuno

Furuno Mu 120c Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

LG 50PM1M - - 50" Plasma Panel Manuel utilisateur

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

NEC

NEC AccuSync LCD5V Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation