Aerohive AP150W Manuel d'installation

Aerohive AP150W Hardware User Guide

Read about and view specifications and compliance information for the AP150W in this topic. Install the

P150W using this topic

The Aerohive AP150W is a compact, lightweight AP that can be mounted directly into a wall plate, or

on a stand on a desktop. The AP150W features two Wi-Fi radios; a fixed 5 GHz 802.11ac Wave 2 radio

and a software-selectable 802.11n 2.4 GHz or 802.11ac 5 GHz radio. Software-selectable radio allows IT

managers to enable 802.11ac performance on both radios for the best coverage and capacity, up to

2.6 Gbps. 3x3:3 SU-MIMO provides 1300 Mbps data rates and 2x2 MU-MIMO provides 867 Mbps data

rates. Built-in BLEprovides proximity, indoor location tracking, and other location-based mobile

engagement services.

The AP150W provides three wired Gigabit Ethernet ports. One of these ports provides PoE (Power over

Ethernet) for applications such as VoIP phones or IPcameras. For wall outlets with more than one cable

or connector, a passive pass-through port on the back of the device allows you to connect the AP150W

without disabling the other cable or connector.

The AP150W has the power to support enterprise-grade features, including built-in application visibility

and control, RADIUS authentication, DHCP, captive web portals, location services and spectrum

analysis.

For more information about Aerohive APs in general, see "Introduction to Aerohive APs"

For information about connecting your APto the network, best-practices, and troubleshooting, see

"Basic Troubleshooting for New Devices".

For hardware compliance statements, see "Regulatory Compliance Statements".

Important! Changing the Country Code

If your access point is configured for the World Regulatory Domain, it is important to set the country

code to the country in which the APwill be deployed to meet regulatory requirements and for optimal

wireless operation. To do this, follow these steps:

The country code selection is for World models only and is not available to FCC, CAN, and

other country-specific models. Per FCC regulations, all Wi-Fi products marketed in the

United States must be set to U.S. channels only.

For Devices Running HiveManager Classic

Page 1 of 1

AP150W Hardware User Guid

201

Preliminarty Draft

Power on the APand allow it to find and connect to HiveManager Classic. Once the

APisconnected, it appears in the table of unconfigured devices on the Monitor > Devices

page and is categorized as New under the Management Status table header.

2. Select the check box for the AP, and then choose Update > Advanced >Update Country.

3. On the Update Country Code page, choose the appropriate country code from the drop-

down list, and then click Upload.

For Devices Running HiveManager NG

1. Power on the AP and allow it to find and connect to HiveManager NG. Once the APis

connected it appears in the table of devices on the Monitor > Devices page.

2. Select the check box next to the AP, and then choose Assign Country Code from the Actions

drop-down list. In the dialog box that appears, select the appropriate country from the drop-

down list, and then click Save.

3. Upload your changes to the device.

Safety Guidelines

The information in this section applies to AP150W devices.

The following safety icons are used in these guidelines to identify the type of precaution:

This icon indicates a general caution. Failure to comply with a caution

notification can result in damage to equipment.

This icon indicates an electrical caution. Failure to comply with an electrical

notification can result in serious injury or death, and extensive damage to

equipment.

The following table lists the safety precautions you should follow when installing your

AP150W devices.

Aerohive devices must be installed by a professional installer who is certified to

install these types of devices and to ensure that they are properly grounded

and meet applicable local and national electrical codes.

These devices are intended for indoor use only.

Do not install the device in an environment where the operating ambient

temperature might exceed the recommended ranges.

Electrical equipment generates heat. Ambient air temperature may not be

adequate to cool equipment to acceptable operating temperatures without

adequate circulation. Be sure that the room where you install your device has

adequate air circulation.

Changes or modifications made to this device that are not expressly approved

by the party responsible for compliance could void the user's authority to

operate the equipment.

Page 2 of 1

AP150W Hardware User Guid

201

Preliminarty Draft

Electrostatic discharge (ESD) can damage equipment and impair electrical

circuitry. ESD damage occurs when electronic components are improperly

handled and can result in complete or intermittent failures. Be sure to follow

ESD-prevention procedures when handling electronic components.

Never assume that power is disconnected from a circuit; always check the

circuit.

To meet radiation exposure requirements in all countries, these devices should

be installed at a minimum distance of 9.05" (23 cm) from people and animals.

See individual country warning for country-specific distances, if required.

All Ethernet and RS232 (console) ports and the cables attached to them are

designed for intra-building connection to other equipment. Do not connect

these ports directly to wiring that exits the building where this appliance is

located

Install the AP150W

The following sections describe how to install your AP150W devices, connect them to the network, and

start managing them in HiveManager NG.

Shipping Carton Contents

The AP150W access point shipping carton contains the following items:

• AP150W chassis

• Generic QuickStart Card

• Wall mounting bracket and mounting hardware packet containing four Phillips screws and

one Torx screw.

•Ethernetcable

Video:Unboxing the AP150W Wallplate Access Point

For mounting instructions, see "Mount the AP150W ".

For information about securing the device, see "Secure the AP150W".

For information about the status indicator light, see "Status Light".

Mount the AP150W to a Wall

Use the following instructions to mount the AP150W directly to an Ethernet cable receptacle box

in a wall.

The mounting bracket has holes for several types of wall receptacles. The holes are

labeled as shown below: UK/EU, US/DUAL, and US/SINGLE.

Page 3 of 1

AP150W Hardware User Guid

201

Preliminarty Draft

1. Remove the wall outlet covering.

2. Attach the wall bracket to the wall with the large opening in the bracket aligned to the hole

in the wall. Use at least two mounting screws to mount the bracket. The illustration below

shows a bracket for a US/SINGLE wall socket.

Page 4 of 1

AP150W Hardware User Guid

201

Preliminarty Draft

3. If necessary, use the short Ethernet cable that ships with the device to connect the Eth0 port

on the back of your device to the jack in the wall.

Page 5 of 1

AP150W Hardware User Guid

201

Preliminarty Draft

4. Attach the device to the bracket by inserting the two tabs on the bracket into the holes in

the back of the device, and the flange on top of the bracket onto the opening at the top of

the device back panel. Push down on the device to seat it on the bracket, as shown in the

illustration. The device will rest on the two flanges at the bottom of the bracket.

Page 6 of 1

AP150W Hardware User Guid

201

Preliminarty Draft

5. Install a screw in the top of the device to secure the unit to the top flange on the bracket.

Page 7 of 1

AP150W Hardware User Guid

201

Preliminarty Draft

Video: Installing the AP150W Wallplate Access Point

Connect the AP150W

Follow these steps to connect your AP150W to power and to the network.

1. Connect a standard RJ45 Ethernet cable from ETH0 on the APto a switch that provides PoE

power, or use a PoE injector (see"Ethernet Ports" ).

2. After the AP receives power, it automatically tries to get network settings and contact

HiveManager NG. This process takes about five minutes. When you see the APlisted on the

Page 8 of 1

AP150W Hardware User Guid

201

Preliminarty Draft

Devices page in the

onitor section of the HiveManager NG GUI, the initial setup is complete

and you can begin managing the AP with HiveManager NG.

Hardware Components

You can see the hardware components of the AP150W in the illustration below and read about them in

the sections that follow.

Component Descriptions

Status Light

The status light conveys operational states for system power, firmware updates, Ethernet and

wireless interface activity, and major alarms. The AP150W has a device status LED and an Ethernet

port status LED.

The device status LED is on the panel to the right of the Ethernet ports. The colors of this LED

indicate the following states of activity:

Dark: There is no power or the status indicator is disabled.

Amber (flashing): This is an alert that indicates that the device is performing a firmware

upgrade. Do not power off the device during this process.

Amber (steady): This is an alert that indicates that the CAPWAP connection has not been

successfully established, or the device is booting or shutting down.

Green: The device is powered on, a successful CAPWAP connection has been made, and the

firmware is operating normally. During normal operation, the LED produces a slow blink

consisting of 4 seconds of illumination followed by one minute of darkness.

To turn the LEDoff or on, or change the brightness using the CLI, enter:

system led brightness [ bright | soft | dim | off]

Page 9 of 1

AP150W Hardware User Guid

201

Preliminarty Draft

You can adjust the brightness level from bright (the default) to soft to dim, or turn it off completely

in HiveManager NG. Navigate to Configure > Network Policy > Additional

Settings>NetworkService > Management Options. Turn Management Options on and scroll

down to the System Settings section. Use the LED brightness drop-down to select the brightness

level that you want.

When you change the brightness setting here, the new setting will apply to all devices

under this network policy. To change the LED brightness for a single device, establish a

console connection and use the CLI command.

For devices running HiveManager Classic, you can set the LEDs for all APs on your network to blink

or remain steady. Navigate to Home> Device Management Settings > LEDMode.

Ethernet Ports

The AP150W has the following RJ45 10/100/1000Base-T/TX Ethernet ports:

• Eth0 / PoE Input: Autosensing 10/100/1000 Base-T Ethernet PoE Input Port

• Eth1 / PoE Output: Autosensing 10/100/1000 Base-T Ethernet PoE Output Port

• Eth2 / Eth3: Autosensing 10/100/1000 Base-T Ethernet Ports

• Two RJ45 passive pass thru ports on the back of the device

•RJ45ConsolePort

Power Options

The AP150W can receive 802.3af and 802.3at PoE and PoE+ power through the Eth0 and Eth1

ports. With 802.3af, there is no PoE budget support on the downlink port. With 802.3af the PoE

budget on the downlink port is 12 W.

The AP150W can also be powered using a 48VDC, 0.75 A power supply (sold as an accessory).

Using this method, the PoE budget on the downlink port is 15.4 W.

Antennas

The AP150W has nine internal antennas:

• Five single-band 5 GHz antennas

• Three dual-band 2.4 GHz or 5 GHz antennas

•One

BLE antenna.

Console Port

Through the Console port, you can make a serial connection between your management system

and the AP. The management station from which you connect to the device using the Console

port must have a VT100 emulation program, such as Tera Term Pro© (a free terminal emulator) or

Hilgraeve HyperTerminal® (provided with Windows® operating systems from XP forward). The serial

connection settings are: 9600 bits per second, 8 data bits, no parity, 1 stop bit, no flow control.

Page 10 of 1

AP150W Hardware User Guid

201

Preliminarty Draft

Table des matières

Autres manuels Aerohive Point d'accès sans fil

Aerohive

Aerohive HiveAP 20 ag Guide de référence rapide

Aerohive

Aerohive AP130 Manuel utilisateur

Aerohive

Aerohive HiveAP 28 Guide de référence rapide

Aerohive

Aerohive AP1130 Manuel utilisateur

Aerohive

Aerohive AP122 Manuel d'installation

Aerohive

Aerohive AP330 Manuel utilisateur

Aerohive

Aerohive HiveAP 340 Manuel utilisateur

Aerohive

Aerohive HiveAP 320 Manuel utilisateur

Aerohive

Aerohive AP370 Manuel utilisateur

Aerohive

Aerohive AP245X Manuel d'installation

Aerohive

Aerohive HiveAP 20 Guide de référence rapide

Aerohive

Aerohive access point Guide de référence rapide

Aerohive

Aerohive HiveAP 340 Manuel utilisateur

Aerohive

Aerohive HiveAP 330 Manuel utilisateur

Aerohive

Aerohive HiveAP 320 Manuel utilisateur

Aerohive

Aerohive Atom AP30 Manuel d'installation

Aerohive

Aerohive AP250 Manuel utilisateur

Aerohive

Aerohive HIVEAP 170 Manuel utilisateur

Aerohive

Aerohive AP230 Manuel utilisateur

Aerohive

Aerohive HiveAP 100 Series Manuel utilisateur

Aerohive

Aerohive AP630 Manuel d'installation

Aerohive

Aerohive HiveAP 340 Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur