Aeon Labs AEO MULTISENS Manuel utilisateur

AEO_MULTISENS

Z-Wave Multisensor

Firmware Version : 1.18

Quick Start

SThis device is a Z-Wave Sensor. Single click the little button behind the battery cover to include or

exclude the device. Clicking the little button behind the battery cover will wake up the device and keep it

awake.

Please refer to the chapters below for detailed information about all aspects of the products usage.

Product description

The Aeon Labs Multisensor is a USB or battery-powered Z-Wave motion sensor, temperature sensor,

humidity sensor and lightness sensor in one package. The sensor will send radio signals up to 6 associated

Z-Wave devices within its own Z-Wave network when the sensor detects IR changes in front of its viewing

window. The Aeon Labs Multisensor complies with the IP43 standard so it can be used outdoors. By

adjusting the sensitivity of the sensor you can avoid the triggering due to small animals like dogs or cats.

The Aeon Labs Multi Sensor is delivered with a swivelling Back-Mount Arm for wall mount and a Back-

Mount Plate for ceiling mount.

Installation Guidelines

1. Release the Multisensor from the mounting by rotating it counterclockwise (sign: "Lock"/ "Unlock")

2. Put the 4 AAA batteries in the battery compartment.

3. The sensor can be mounted as follows:

(a) For wall mount use the screws with the swivelling Back-Mount Arm. Further fix the sensor with Back-

Mount Plate like shown in the picture.

Important: The Multisensor should be mounted with the Temperature/Humidity Sensor facing downwards

and positioned on the bottom of the unit to protect it from snow and rain.

(b) For ceiling mount use the screws with the Back-Mount Plate.

4. Mount the Multisensor on the Mount Plate by rotating it clockwise to the "Lock" sign.

The next pictures are showing the effective motion sensor range for ceiling and wall mounting.

Behavior within the Z-Wave network

IOn factory default the device does not belong to any Z-Wave network. The device needs to join an

existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also leave a network. This process is called Exclusion. Both processes are initiated by the

primary controller of the Z-Wave network. This controller will be turned into exclusion respective inclusion

mode. Please refer to your primary controllers manual on how to turn your controller into inclusion or

exclusion mode. Only if the primary controller is in inclusion or exclusion mode, this device can join or leave

the network. Leaving the network - i.e. being excluded - sets the device back to factory default.

If the device already belongs to a network, follow the exclusion process before including it in your network.

Otherwise inclusion of this device will fail. If the controller being included was a primary controller, it has to

be reset first.

Make sure that your Z-Wave Controller is in the Inclusion-/Exclusion-Mode. Click the little button behind the

battery to confirm the process.

A successful Inclusion/Exclusion lights up the sensor LED for a few seconds.

Operating the device

The Multisensor reports the temperature, humidity and lightness by request to a Z-Wave gateway or

controller. The sensor will send radio signals up to 6 associated Z-Wave devices within its own Z-Wave

network.

The sensitivity of the motion detector can be manually adjusted via the Sensitivity Knob at the battery cover.

To increase the sensitivity rotate the Knob clockwise, to decrease it rotate it counterclockwise.

Wakeup Intervals - how to communicate with the device?

WThis device is battery operated and turned into deep sleep state most of the time to save battery

life time. Communication with the device is limited. In order to communicate with the device, a static

controller Cis needed in the network. This controller will maintain a mailbox for the battery operated devices

and store commands that can not be received during deep sleep state. Without such a controller,

communication may become impossible and/or the battery life time is significantly decreased.

This device will wakeup regularly and announce the wakeup state by sending out a so called Wakeup

Notification. The controller can then empty the mailbox. Therefore, the device needs to be configured with

the desired wakeup interval and the node ID of the controller. If the device was included by a static

controller this controller will usually perform all necessary configurations. The wakeup interval is a tradeoff

between maximal battery life time and the desired responses of the device.

A single click on the little button behind the battery will wake up the device and keep it awake.

It is possible to set the node ID to 255 to send wakeup notifications as broadcast. In this mode device takes more time to

go to sleep and drains battery faster, but can notify all it's direct neighbors about a wakeup.

Node Information Frame

NI The Node Information Frame is the business card of a Z-Wave device. It contains information

about the device type and the technical capabilities. The inclusion and exclusion of the device is confirmed

by sending out a Node Information Frame. Beside this it may be needed for certain network operations to

send out a Node Information Frame.

A single click on the little button behind the battery sends a Node Information Frame.

Associations

AZ-Wave devices control other Z-Wave devices. The relationship between one device controlling

another device is called association. In order to control a different device, the controlling device needs to

maintain a list of devices that will receive controlling commands. These lists are called association groups

and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event

happens all devices stored in the respective association group will receive a common wireless command.

Association Groups:

1Devices to be switched on upon motion deteced and off after a timeout (on time) (max. nodes in

group: 5)

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can

adapt the function better to user needs or unlock further enhanced features.

IMPORTANT: Controllers may only allow to configure signed values. In order to set values in the range 128

… 255 the value sent in the application shall be the desired value minus 256. For example: to set a

parameter to 200? it may be needed to set a value of 200 minus 256 = minus 56. In case of two byte value

the same logic applies: Values greater than 32768 may needed to be given as negative values too.

Sensor report type on Get without instances (Parameter Number 1, Parameter Size 1) Which type of multi

sensor report should be sent on multi sensor Get command without instances

Value Description

0 Temperature, humidity and luminance (Default)

1 Temperature

2 Luminance

3 Humidity

Wake up 10 minutes when batteries are inserted (Parameter Number 2, Parameter Size 1) Stay awake for

10 minutes after batteries are inserted

Value Description

0 No (Default)

1 Yes

On time (Parameter Number 3, Parameter Size 2) How long should the device associated to multi senor

keep state On before sending it Off command (if the value is bigger than 255, the value would be rounded to

next integer in minutes)

Value Description

1 — 15300 sec (Default 240)

Enable motion sensor (Parameter Number 4, Parameter Size 1)

Value Description

0 Disabled

1 Enabled (Default)

Send unsolicited reports periodicaly. Interval group 1 (Parameter Number 101, Parameter Size 4)

Which reports need to send automatically in timing intervals for group 1

Value Description

0 Battery report (Default)

5 Temperature

6 Luminosity

7 Humidity

Send unsolicited reports periodicaly. Intervcal group 2 (Parameter Number 102, Parameter Size 4)

Which reports need to send automatically in timing intervals for group 2

Value Description

0 Battery report (Default)

5 Temperature

6 Luminosity

7 Humidity

Send unsolicited reports periodicaly. Intervcal group 3 (Parameter Number 103, Parameter Size 4)

Which reports need to send automatically in timing intervals for group 3

Value Description

0 Battery report (Default)

5 Temperature

6 Luminosity

7 Humidity

Unsolicitate reports interval for timing groups 1 (Parameter Number 111, Parameter Size 4) Interval to send

out reports to timing group 1

Value Description

1 —

2678400 sec (Default 720)

Unsolicitate reports interval for timing groups 2 (Parameter Number 112, Parameter Size 4) Interval to send

out reports to timing group 2

Value Description

1 —

2678400 sec (Default 720)

Unsolicitate reports interval for timing groups 3 (Parameter Number 113, Parameter Size 4) Interval to send

out reports to timing group 3

Value Description

1 —

2678400 sec (Default 720)

Technical Data

IP Rating IP 43

Battery Type 4 * AAA

Wireless Range up to 100 m outside, on average up to 20 m inside buildings

Explorer Frame Support No

SDK 5.03

Device Type Slave with routing capabilities

Generic Device Class Multilevel Sensor

Specific Device Class Routing Multilevel Sensor

Routing Yes

FLiRS No

Firmware Version 1.18

Table des matières

Autres manuels Aeon Labs Capteur de sécurité

Aeon Labs

Aeon Labs Aeotec MULTISENSOR 6 Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur