AEG SANTO Manuel utilisateur
SANTO
ARCTIS
Integrierbare Unterbau-Kühl- und
Gefriergeräte
Réfrigérateurs et congélateurs sous-plan
à intégrer
Geïntegreerde onderbouwkoel- en
vriesapparaten
Integrated built-under refrigerators and
freezers
Integrerbara underbänk-kyl- och frysskåp
Työtason alle asennettavat jääkaapit ja
pakastimet
DMontageanweisung 2-10
FInstructions de montage 11-19
NMontage-aanwijzing 20-28
tInstallation instructions 29-37
SMonteringsanvisning 38-46
qAsennusohjeet 47-55
Grid preparation t
When changing the side at which the door opens, remove plug from
the mains.
Left door opening:
☞Remove the left side (A) of the grid cutting
it from the rear (see figure)
Right door opening:
☞Remove the right side (B) of the grid cutting
it from the rear (see figure)
Re-install the grid to the base of the appli-
ance by pushing on to the clasps (a) until
they click.
To reverse the opening direc-
tion of the door, proceed as
shown in the figures:
29
a
a
DO002/2
A
B
Reversing the door
The side at which the door opens can be changed from the right side
(as supplied) to the left side, if the installation site requires.
1
1
23
4
5
Changing over the freezer compartment door
(not on all models)
30
6
8
7
2
3
10
11
9
12
13
Warning! After completion of
the door reversing operation,
check that the door gasket
adheres to the cabinet. If the
ambient temperature is cold
(i.e. in Winter), the gasket
may not fit perfectly to the
cabinet. In that case, wait for
the natural fitting of the
gasket or accelerate this pro-
cess by heating up the part
involved with a normal hair-
dryer on a low setting.
☞Open the freezer compartment door a
little way.
Using a small screwdriver, press the
spring in the opening of the lower door
bearing slightly upwards and take the
door bearing out complete with the
door.
☞
31
Position the covering cap (M) on the
opposite side.
Turn the freezer compartment door
through 180° and fit the lower door
bearing into the lower bearing cavity
of the freezer compartment door.
Lift the freezer compartment door a
little way upwards, fit it into the
upper door bearing, and at the same
time insert the lower door bearing
into the square hole. Small upwards
and downwards adjustments of the
freezer compartment door will make
fitting easier.
☞
☞
☞
AEG43
M
Installation kit
1
1xA
12
1xB 2xC
2
2
1
12
600
550
min.
600
Building the appliance in under a worktop
The dimensions of the recessed
installation area must correspond
with those indicated in the figure.
☞
32
Two cabinet securing brack-
ets are supplied with the
installation pack. They need
to be assembled onto the
cabinet prior to cabinet
being pushed into the
Kitchen aperture.
To fit these brackets remove
the two screws at the top
☞
☞
Right hand
bracket
1/a
Left hand
bracket
Push the appliance into
place. The plug socket
necessary for connection
of the appliance to the
electricity supply should be
positioned, so that the
plug is not placed in the
recess.
To adjust the height pro-
ceed as follows:
Loosen or tighten the two
front feet.
☞
☞
596
555
max
Li89 +
-
2
II52
If necessary, pads are supplied for the
rear feet to make sliding the appliance
in and out of the recess easier. To fit the
pads, press them onto the rear feet.
If required, the dimensions of these
pads can be reduced by breaking them
where marked.
☞
2/a
left and right hand front corners of the cabinet.
Position the two brackets as shown in the figure and replace the two
securing screws.
☞
The rear feet are adjusted by turning the screw in the front kick plate
to the left or right.
☞
33
Screw appliance into place
5
☞The joint cover (B) is to be
assembled after having
installed the appliance in the
recess.
3
1
2
B
4
115°
34
Mounting furniture door
7
6
a
b
10
12
3
4
C
8
ab
clic
clic
c
C
C
35
10
12
3
45
°
11 =
=
10
Upper part of kitchen furniture panel
9b
a
==
1
2
Lower part of kitchen furniture
panel
9/a
275 275
max 100
36
Refit the covering strip.
☞
13
A
12
37
Fitting the plinth
Important!
For the efficient operation of the appli-
ance, it is important that the original
ventilation grid is used.
• For an opening height dimension
A=820 mm and a plinth height
dimension a=100 mm, the plinth
may be fitted without adjustments.
The same applies to an opening
height dimension B=870 mm and a
plinth height dimension b=150 mm.
• For plinth heights greater than
a=100 mm, b=150 mm, a cut should
be made in the plinth, 580 mm wide,
in the centre of the appliance
position, leaving a remaining height
of a=100 mm, b=150 mm.
• Attach plinth to the kitchen units.
008
580
a=100
b=150
25-80
A=820
B=870
25
Important! The plinth must be positioned at a minimum distance of
25 mm from the door.
Autres manuels pour SANTO
16
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels AEG Réfrigérateur
AEG
AEG SFB612F1DS Manuel utilisateur
AEG
AEG SKZ81840F0 Manuel utilisateur
AEG
AEG S72300DSX1 Manuel utilisateur
AEG
AEG SCT81900S0 Manuel utilisateur
AEG
AEG OKO-SANTO 2642-6 KG Manuel utilisateur
AEG
AEG RKB738E3MX Manuel utilisateur
AEG
AEG SANTO Manuel utilisateur
AEG
AEG NSF6I82EF Manuel utilisateur
AEG
AEG RKB638E2MX Manuel utilisateur
AEG
AEG SANTO K 7 10 43-7i Manuel utilisateur
AEG
AEG OKO_SANTO 1504-4 Manuel utilisateur
AEG
AEG Santo 1402u Manuel utilisateur
AEG
AEG OKO-Santo 1450-6 TK Manuel utilisateur
AEG
AEG SKS38840S0 Manuel utilisateur
AEG
AEG SANTO 3150 Manuel utilisateur
AEG
AEG SKE58221AF Manuel utilisateur
AEG
AEG SKE818E9ZC Manuel utilisateur
AEG
AEG RCB632D4MM Manuel utilisateur
AEG
AEG SKE818F1DC Manuel utilisateur
AEG
AEG SFE818E1DS Manuel utilisateur
