Advancode QC 2D Series Manuel utilisateur

QC 2D Series :

QC625X

QC635x

QC715X

QC725X

QC755X

User Guide

Disclaimer

Please read through the manual carefully before using the product and operate it according to the manual. It is

advised that you should keep this manual for future reference.

Do not disassemble the device or remove the seal label from the device. Otherwise, AdvanCode Technology

Co., Ltd. does not assume responsibility for the warranty or replacement.

All pictures in this manual are for reference only and actual product may differ. Regarding to the product

modification and update, AdvanCode Technology Co., Ltd. reserves the right to make changes to any

software or product to improve reliability, function, or design at any time without notice. Besides, the

information contained herein is subject to change without prior notice.

The products depicted in this manual may include software copyrighted by AdvanCode Technology Co., Ltd. or

a third party. The user, corporation or individual, shall not duplicate, in whole or in part, distribute, modify,

decompile, disassemble, decode, reverse scannerer, rent, transfer or sublicense such software without prior

written consent from the copyright holders.

This manual is copyrighted. No part of this publication may be reproduced or distributed in any form without

written permission from AdvanCode.

AdvanCode Technology Co., Ltd. reserves the right to make final interpretation of the statement above.

Table Of Contents

Chapter 1 Getting Started..................................................................................................................................1

Introduction..............................................................................................................................................1

About This Guide.....................................................................................................................................1

Barcode Scanning...................................................................................................................................2

Barcode Programming.............................................................................................................................2

Factory Defaults.......................................................................................................................................3

Custom Defaults......................................................................................................................................3

Chapter 2 Communication Interfaces..............................................................................................................4

Power-Saving Mode................................................................................................................................4

RS-232 Interface......................................................................................................................................5

Baud Rate.........................................................................................................................................6

Parity Check .....................................................................................................................................7

Data Bit.............................................................................................................................................7

Data Bit & Parity Check....................................................................................................................8

Stop Bit .............................................................................................................................................8

USB Interface .........................................................................................................................................9

USB Enumeration.............................................................................................................................9

USB HID-KBW..................................................................................................................................9

USB Country Keyboard Types................................................................................................10

Beep on Unknown Character..................................................................................................12

Inter-Keystroke Delay..............................................................................................................12

Convert Case...........................................................................................................................13

USB COM Port Emulation..............................................................................................................13

Chapter 3 Scan Mode.......................................................................................................................................14

Batch Mode............................................................................................................................................14

Trigger Mode .........................................................................................................................................15

Decode Session Timeout ...............................................................................................................15

Level Trigger/Pulse Trigger............................................................................................................16

Auto Sleep......................................................................................................................................16

Sense Mode...........................................................................................................................................17

Decode Session Timeout ...............................................................................................................17

Image Stabilization Timeout...........................................................................................................17

Continue after Good Decode..........................................................................................................18

Timeout between Decodes (Same Barcode).................................................................................18

Sensitivity........................................................................................................................................19

Continuous Mode...................................................................................................................................21

Decode Session Timeout ...............................................................................................................21

Timeout between Decodes.............................................................................................................21

Cellphone Read Mode...........................................................................................................................22

Chapter 4 Scanning Preferences....................................................................................................................23

Introduction............................................................................................................................................23

Decode Area..........................................................................................................................................23

Whole Area Decoding.....................................................................................................................23

Central Area Decoding...................................................................................................................23

Specify Central Area.......................................................................................................................24

Chapter 5 Illumination & Aiming.....................................................................................................................25

Illumination.............................................................................................................................................25

Aiming....................................................................................................................................................26

Chapter 6 Beep & LED Indications.................................................................................................................27

Startup Beep..........................................................................................................................................27

Beep after Good Decode (Non-programming Barcode).......................................................................28

Beep Type.......................................................................................................................................28

Beep Volume..................................................................................................................................29

Beep on Unknown Character................................................................................................................29

Beep after Good Decode (Programming Barcode)...............................................................................30

LED Notification for Good Decode........................................................................................................30

Transmit NGR Message........................................................................................................................31

Edit NGR Message.........................................................................................................................31

Chapter 7 Data Formatting..............................................................................................................................32

General Settings....................................................................................................................................33

Enable/Disable All Prefix/Suffix......................................................................................................33

Prefix Sequences............................................................................................................................33

Custom Prefix........................................................................................................................................34

Enable/Disable Custom Prefix........................................................................................................34

Set Custom Prefix...........................................................................................................................34

AIM ID Prefix..........................................................................................................................................35

Code ID Prefix .......................................................................................................................................35

Restore All Default Code IDs..........................................................................................................35

Modify Code ID...............................................................................................................................36

Custom Suffix ........................................................................................................................................39

Enable/Disable Custom Suffix........................................................................................................39

Set Custom Suffix...........................................................................................................................39

Terminating Character Suffix.................................................................................................................40

Enable/Disable Terminating Character Suffix................................................................................40

Set Terminating Character Suffix...................................................................................................41

Chapter 8 Symbologies...................................................................................................................................42

General Settings....................................................................................................................................42

Enable/Disable All Symbologies.....................................................................................................42

Enable/Disable 1D Symbologies....................................................................................................42

Enable/Disable 2D Symbologies....................................................................................................42

Video Reverse................................................................................................................................43

1D Symbologies.....................................................................................................................................44

Code 128........................................................................................................................................44

Restore Factory Defaults.........................................................................................................44

Enable/Disable Code 128........................................................................................................44

Set Length Range for Code 128.............................................................................................44

GS1-128 (UCC/EAN-128) ..............................................................................................................45

Restore Factory Defaults.........................................................................................................45

Enable/Disable GS1-128.........................................................................................................45

Set Length Range for GS1-128...............................................................................................45

AIM-128 ..........................................................................................................................................46

Restore Factory Defaults.........................................................................................................46

Enable/Disable AIM-128..........................................................................................................46

Set Length Range for AIM-128 ...............................................................................................46

EAN-8 .............................................................................................................................................47

Restore Factory Defaults.........................................................................................................47

Enable/Disable EAN-8.............................................................................................................47

Transmit Check Digit...............................................................................................................48

Add-On Code...........................................................................................................................48

Add-On Code Required...........................................................................................................49

EAN-8 Extension.....................................................................................................................49

EAN-13 ...........................................................................................................................................50

Restore Factory Defaults.........................................................................................................50

Enable/Disable EAN-13...........................................................................................................50

Transmit Check Digit...............................................................................................................50

Add-On Code...........................................................................................................................51

Add-On Code Required...........................................................................................................51

ISSN................................................................................................................................................52

Restore Factory Defaults.........................................................................................................52

Enable/Disable ISSN...............................................................................................................52

Add-On Code...........................................................................................................................53

Add-On Code Required...........................................................................................................53

ISBN................................................................................................................................................54

Restore Factory Default ..........................................................................................................54

Enable/Disable ISBN...............................................................................................................54

Set ISBN Format .....................................................................................................................54

Add-On Code...........................................................................................................................55

Add-On Code Required...........................................................................................................55

UPC-E.............................................................................................................................................56

Restore Factory Defaults.........................................................................................................56

Enable/Disable UPC-E............................................................................................................56

Transmit Check Digit...............................................................................................................56

Add-On Code...........................................................................................................................57

Add-On Code Required...........................................................................................................57

Transmit System Character “0” ...............................................................................................58

UPC-E Extension ....................................................................................................................58

UPC-A.............................................................................................................................................59

Restore Factory Defaults.........................................................................................................59

Enable/Disable UPC-A............................................................................................................59

Transmit Check Digit...............................................................................................................59

Add-On Code...........................................................................................................................60

Add-On Code Required...........................................................................................................60

Transmit Preamble Character “0”............................................................................................61

Interleaved 2 of 5............................................................................................................................62

Restore Factory Defaults.........................................................................................................62

Enable/Disable Interleaved 2 of 5...........................................................................................62

Set Length Range for Interleaved 2 of 5.................................................................................62

Check Digit Verification...........................................................................................................63

ITF-14 .............................................................................................................................................64

ITF-6 ...............................................................................................................................................65

Matrix 2 of 5....................................................................................................................................66

Restore Factory Defaults.........................................................................................................66

Enable/Disable Matrix 2 of 5...................................................................................................66

Set Length Range for Matrix 2 of 5.........................................................................................66

Check Digit Verification...........................................................................................................67

Industrial 2 of 5...............................................................................................................................68

Restore Factory Defaults.........................................................................................................68

Enable/Disable Industrial 2 of 5 ..............................................................................................68

Set Length Range for Industrial 2 of 5....................................................................................68

Check Digit Verification...........................................................................................................69

Standard 2 of 5（IATA 2 of 5）......................................................................................................70

Restore Factory Defaults.........................................................................................................70

Enable/Disable Standard 25 ...................................................................................................70

Set Length Range for Standard 25.........................................................................................70

Check Digit Verification...........................................................................................................71

Code 39 ..........................................................................................................................................72

Restore Factory Defaults.........................................................................................................72

Enable/Disable Code 39..........................................................................................................72

Transmit Start/Stop Character ................................................................................................72

Set Length Range for Code 39 ...............................................................................................73

Check Digit Verification...........................................................................................................73

Enable/Disable Code 39 Full ASCII........................................................................................73

Codabar..........................................................................................................................................74

Restore Factory Defaults.........................................................................................................74

Enable/Disable Codabar .........................................................................................................74

Set Length Range for Codabar...............................................................................................74

Check Digit Verification...........................................................................................................75

Transmit Start/Stop Character ................................................................................................75

Start/Stop Character Format...................................................................................................76

Code 93 ..........................................................................................................................................77

Restore Factory Defaults.........................................................................................................77

Enable/Disable Code 93..........................................................................................................77

Set Length Range for Code 93 ...............................................................................................77

Check Digit Verification...........................................................................................................78

GS1-Databar (RSS)........................................................................................................................79

Restore Factory Defaults.........................................................................................................79

Enable/Disable GS1 Databar..................................................................................................79

Transmit Application Identifier “01” .........................................................................................79

Code 11 ..........................................................................................................................................80

Restore Factory Defaults.........................................................................................................80

Enable/Disable Code 11..........................................................................................................80

Set Length Range for Code 11 ...............................................................................................80

Transmit Check Digit...............................................................................................................81

Check Digit Verification...........................................................................................................81

Plessey ...........................................................................................................................................82

Restore Factory Defaults.........................................................................................................82

Enable/Disable Plessey...........................................................................................................82

Set Length Range for Plessey ................................................................................................82

Check Digit Verification...........................................................................................................83

MSI-Plessey....................................................................................................................................84

Restore Factory Defaults.........................................................................................................84

Enable/Disable MSI-Plessey...................................................................................................84

Set Length Range for MSI-Plessey.........................................................................................84

Transmit Check Digit...............................................................................................................85

Check Digit Verification...........................................................................................................85

2D Symbologies.....................................................................................................................................86

PDF 417..........................................................................................................................................86

Restore Factory Defaults.........................................................................................................86

Enable/Disable PDF 417.........................................................................................................86

Set Length Range for PDF 417...............................................................................................86

PDF 417 Twin Code................................................................................................................87

QR Code.........................................................................................................................................88

Restore Factory Defaults.........................................................................................................88

Enable/Disable QR Code........................................................................................................88

Set Length Range for QR Code..............................................................................................88

Micro QR .................................................................................................................................88

QR Twin Code.........................................................................................................................89

Data Matrix......................................................................................................................................91

Restore Factory Defaults.........................................................................................................91

Enable/Disable Data Matrix.....................................................................................................91

Set Length Range for Data Matrix...........................................................................................91

Rectangular Barcode...............................................................................................................92

Mirror Image............................................................................................................................92

Data Matrix Twin Code............................................................................................................93

Chapter 9 Image Control .................................................................................................................................94

Ambient Illumination..............................................................................................................................94

Image Flipping.......................................................................................................................................95

Flip..................................................................................................................................................96

Flip Vertically ..................................................................................................................................96

Flip Horizontally..............................................................................................................................96

Chapter 10 Troubleshooting...........................................................................................................................97

FAQ........................................................................................................................................................97

Appendix...........................................................................................................................................................99

Appendix 1: Factory Defaults Table......................................................................................................99

Appendix 2: AIM ID Table....................................................................................................................106

Appendix 3: Code ID Table .................................................................................................................108

Appendix 4: ASCII Table.....................................................................................................................109

Appendix 5: Parameter Programming Examples................................................................................113

a. Program the Decode Session Timeout....................................................................................113

b. Program the Time Period from Idle to Sleep............................................................................113

c. Program the Image Stabilization Timeout................................................................................113

d. Program the Timeout between Decodes (Same Barcode)......................................................114

e. Program the Threshold Value of Illumination Change.............................................................114

f. Program the Timeout between Decodes...................................................................................114

g. Program the Central Area.........................................................................................................115

h. Program the Custom Prefix/Suffix............................................................................................115

i. Program the Terminating Character Suffix................................................................................115

j. Program the Code ID.................................................................................................................116

k. Program the NGR Message .....................................................................................................116

l. Program the Length Range (Maximum/Minimum Lengths) for a Symbology...........................117

Appendix 6: Digit Barcodes.................................................................................................................118

Appendix 7: Save/Cancel Barcodes....................................................................................................120

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Advancode Lecteur de codes-barres

Advancode

Advancode QC 1D Series Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur